objects from o 3d models

A simple door holder that prevents a door from closing completely. Designed in Fusion360. The holder could also be simply glued with powerstrips. I decided to fix it again with small screws for safety. Due to the simple screw connection, the...

If it causes copyright issues, i will remove it. Remixed from: https://www.thingiverse.com/thing:4248444 https://www.thingiverse.com/thing:4614658 https://www.thingiverse.com/thing:2506910 https://www.thingiverse.com/thing:3853037...

*I used brims on: windshield front_hub_bolts front_glow_red back_glow_red axles 5 - The windshield prints well, however depending on your slicer settings/filament/printer, one edge may suffer from overextrusion. If this happens on your print, do...

Note: live picture taken from the 6" version. Now lets check the claims: <h1>1) super light yet crazily stiff</h1> This 7" frame does weight around 60-85g in total (depending on the rod strength and used mounts). This inclused the GoPro as...

Base: I used some 2x4mm magnets that were left over from the MakerRx kit to hold the Base Cover to the Base. The Base can be printed without supports. I manually added a small support for the cord slot inside the Base. After printing, just pop it...

I'll just explain how to properly fill and drain the tank and how to agitate.FillingRemove the cap from the lid (DO NOT REMOVE THE LID ONCE THE FILM IS INSIDE), rotate the lid so that the arrow is pointing the drainage port on the side of the...

These add spacing between the fork &amp; your pannier hooks to prevent them from scratching the paint on your fork. I designed these to have the standoffs up instead of down when installed. Can't think of a good reason why the other way would be...

I recommend letting Hugin pick the render resolution and then cropping and (down) scaling to the appropriate square image: stitching four 6000x4000 images from my NEX-7 nominally produces a 7648x7648 result (approximately 30x30mm at camera native...

&nbsp;I reprinted the part with a raft and it fit much better)3 - Optionally, for an optimal joint between the hat_bottom and the hat_band, the top layers of the hat_bottom can be printed at a lower layer height to help smooth it out a bit.4 - When...

In marlin you need to find what you need uncomand it and compile and flash the firmware, in klipper you simply copy and paste few lines from the documentation and save it.Input shaping. The best feature of the klipper. it compensate the vibrations of...

Aiyima has a few 5.25" woofers (that should fit) to choose from. - I use these <a href="https://s.click.aliexpress.com/e/_AWLfG0">speaker terminal connectors (around € 0.5/5 pieces)</a> but they are basically optional. - Plus <a...

An exemplar of woven wire container designed for Customer Service Representatives (CSR) A specific type of wire-constructed basket intended to cater to the needs of Client Support Representatives (CSR) A unique variety of woven wire receptacle...

You can feel the initial resistance to the file from the ridges. Notice how, after a dozen light strokes you can feel that resistance fade ... you've knocked down the ridges. I then roll the part while it is on the cylindrical file and I file down...

&nbsp; Each bracket takes about 5 ½ hours with the 0.20 mm quality setting on Prusa mini or double that for the MK3 .Posts: From 6 up to 9 can be printed at a time on the Prusa Mini or more on the Prusa MK3. &nbsp; Note that the models are laid...

Ensure all the supports have been removed from the two halves of the shell (particularly the small support underneath the overhang for the left shoulder button. To get a cleaner feel for the buttons use coarse, followed by fine, sandpaper inside...

If it causes copyright issues, i will remove it. Remixed from: https://www.thingiverse.com/thing:4248444 https://www.thingiverse.com/thing:4614658 https://www.thingiverse.com/thing:2506910 https://www.thingiverse.com/thing:3853037...

Create a table top in the range of 15 inches to 18 inches in diameter from your desired material or 3D print and assemble the 8 Table-Top Wedge Pieces using the M8 Nuts and Bolts in the 2 slots on each side of the pieces. Place the assembled...

This should help keep the runout sensor from binding the filament. To assemble, a) drill out the &nbsp;4mm holes in the end bracket and pivot to 4mm; b) heat up the rod and slide the pivot over it, then let it cool down and slide it back and forth...

But then the blinds will block your windows from opening.With this magnetic mount you can easily remove the blinds in case you want to open your window.&nbsp;How many mounts do I need for one FYRTUR or KADRILJ? It depends on the lenght of your blind...

(Removed: I'll make this a different ornament) Made "hexagons" varying number of sides, giving more variety to the snowflakes. Made 'hexagon' widths slightly random added 'minthickness' tweak, so you can set this to ensure that all lines are thick...

Pneumatic Push-in Fitting Removal Tool This is a tool for removing the standard push-in fittings from pneumatic equipment. Made for both 4mm and 6mm tubes. I couldn't find any already-made tool models for this job, so I thought I will make my...

When the soap has become creamy or runny, you can remove the bowl from the pot (caution hot ⚠️&nbsp;!)&nbsp; &nbsp; 7. Now put the mold together and grease it with some oil so that the soap can be removed later (I used some olive oil here)</p><figure...

Pair it with the 14.5 x 6 cm eraser (purchasable from Amazon at http://www.amazon.es/gp/product/B008OEBSFA/ref=oh_details_o03_s00_i00?ie=UTF8&psc=1). This wall-mounted eraser holder is suitable for any whiteboard or blackboard eraser. It works...

Every piece took about 6 hours to print and weighs about 50 g.Mark every piece to not lose track of already printed pieces and its position.I cut out all thediffuser panels frompaper, but you can also use the supplied diffuser file toprint them.Step...

Lid Dimensions: 110 mm Ø x 11 mm height The lid is simply inserted from above into or onto the lithophane cylinder. It has ventilation slots so that the heat can escape. In addition, the pattern in the lid provides a beautiful play of light/shadow...

21,000 Lumen output from 150 watts10. Dimmable via 0-10 Voltage DimmingSuperior LED Benefits1. 60,000 hour lifespan.2. Can SAVE 50% or more on energy.3. Qualifies retrofit projects for financial incentives, including utility rebates, tax credits and...

To help me keep designing and uploading more things, you can tip me via 'Buy Me a Coffee' here:&nbsp;https://www.buymeacoffee.com/JoshForwood&nbsp;In addition to the printed parts, you'll also need:2x 10mmOD/9mm Compressed Length/50mm Free Length...

This helmet can support the following: - A suite of Picatinny rail compatible side attachments from Halo: Infinite and Halo: Reach - A flat, universal overhead mounting plate - Multiple UA attachment upgrades - A suite of legacy ODST attachments -...

&nbsp;The air flow direction should be pulling air from inside the enclosure to outside.Place the second TPU_Fan_Gasket_X2 on top of the fan.*Place the PETG_Fan_Exhaust_Adapter_Bracket_X1 on top of the TPU_Fan_Gasket_X2.Insert the screws that came...

print the uppers in a 100% infill! Shroud to complete the FGC-68 do you need to select the Shroud that you like these come in 3 models N (no top rail) TR (with top rail) LR (lower Top RAIL) Link to shrouds FGC-68 Top rail shroud set paintball magfed...