octoprint psu control relay 3d models

Those are cool looking and I love the ESP line of chips, but I really wanted something directly connected so it could get immediate events and feedback, as well as act as a pause and cancel control. This pairs with an OctoPrint plugin, available on...

I WILL APPRECIATE YOUR CONSTRUCTIVE CRITICISM I wanted to easily control some functions on my CR10s particularly since I put it inside an enclosure. However, all the designs I found on Thingiverse use the 6x6 tactile push buttons. I wanted to use the...

Here are the components you'll need for a 20A PSU and a single-channel relay enclosure. The cost is relatively low, significantly less than what it would be to use acrylic glass as originally planned. The modifications I made include: * A vibration...

I constructed a basic PSU control system for my CR-10 printer. ...For guidance, please refer to the instructions outlined in this video: https://youtu.be/dQNBeAZpRmk.

I recently developed a straightforward PSU control unit for my personal CR-10. ...To assemble this project, please refer to the detailed instructions found in this YouTube video: https://youtu.be/dQNBeAZpRmk

This one can also contain a 2-channel relay board to remotely cut off power to the printer, an Orange Pi Zero Plus to run OctoPrint, a 5V AC/DC to power the Orange Pi, and an 8x8cm fan to cool down the PSU, the Orange Pi and the AC/DC board. My...

I remixed couple models on the upper tray using the PSU control app within OctoPrint. It's a great way to monitor and control your power supply. The 12V fan I used is silent, but you can use another one if you want. Just make sure it fits in the...

The purpouse of this project is controlling printer power and an external light with OCTOPRINT, as well as all the tools Octopi includes. Raspberry is holded in its own case. ... It is a remix from a 2 realy box:...

This relay module can be controlled by Octoprint, allowing me to turn devices connected to it on or off remotely. To use this system, I just need to install the "PSUSupply" plugin and connect the relays to my RaspberryPi. ...With this setup, I can...

This is a combined enclosure design for an OctoPrint controller featuring the mounting of a Raspberry Pi 3B and a single 26mm x 50mm (20.5mm x 44.5mm holes) 120/240v 10A relay. The relay can be found here:...

Compact enclosure designed specifically for housing a Crydom D2410 solid state relay, successfully utilized to regulate printer power through integration with OctoPrint.

I'm using this plugin in Octoprint to toggle the relay, which is connected to one of the Pi output pins: https://plugins.octoprint.org/plugins/psucontrol/. The Octopod mobile app also supports this plugin, so you'll be able to turn on/off via your...

Required parts are: * Raspberry Pi 3 * Fotek 220v SSR * 5v 4010 Fan * 12mm Push Button * 5v 5A smps in 87*58*35mm dimensions ([Example](https://www.aliexpress.com/item/1005002728038351.html)) * Male And Female power socket (Shown in pic) * Your...

Another Control Box for OctoPrint. Materials List: - 5V Power Supply (MeanWell, RS-15-5) - 5V Relay (Keyes-019) - IEC 320 C13 and C14 with Fuse (https://www.aliexpress.com/item/32450127290.html?spm=a2g0s.9042311.0.0.5ccc63c08IhJp0) - 2 Switches...

I needed a case to store my octoprint box consisting of an RPI3b+ and a KEYESTUDIO 4-channel relay PI-hat board. I started from this box that I slightly modified. I enlarged the hole for the SD card which was a little tight, I added holes to pass the...

I needed a case to store my octoprint box consisting of an RPI3b+ and a KEYESTUDIO 4-channel relay PI-hat board. I started from this box that I slightly modified. I enlarged the hole for the SD card which was a little tight, I added holes to pass...

Raspbery Pi 3** or better Octropi image for the Raspberry Pi Some MOSFET modules to control lights and power relay I recommend a 64GB SD card for use with timelapse Raspberry Pi Camera, Wide angle helps here! Long cable for camera A 5v power supply,...

Box for relays and step-down converter for control lights, fans, printer power and more via GPIO.I used 12V led strips and fans, so I needed a step-down converter from 24V PSU.To use a 5V relay with raspberry pi, remove the VCC -> JD-VCC jumper...

This text appears to be a tutorial on setting up OctoPrint, a software for controlling 3D printers, on a Raspberry Pi. The tutorial covers the following steps: 1. Installing OctoPrint on the Raspberry Pi 2. Configuring the printer and light settings...

This is a replacement housing for use with a 12vdc 433mhz relay controller. The supplied case that comes with the module barely has room for the module and trying to cram wires into the case is messy. I drew up two versions - one with screw holes...

Here are some accessories designed specifically for a 3D printer server, including relays and camera mounts that can be easily integrated into the system. To get started, you'll need a reliable webcam such as the Logitech model, which is known for...

Electrical Control Panel for Smartphones by Samsung Innovations

This is a remix from https://www.thingiverse.com/thing:4674214 i have constructed my own panel and integrated my own ventilation control via an arduino nano.

... firmly using 30/30 deep-thread particle board screws. I will utilize this power supply to power my Raspberry Pi (loaded with OctoPrint) via a step-down buck converter. ...It will also provide power for the 12V computer fans and 12V UV lights.

Octoprint Raspberry Pi Zero W with 30A relay module case for mounting on Ender 3 PSU (or wherever you want) to control prints and printer shutdown after prints or in case of emergencies.

I designed this cover specifically for the Sparkfun Beefcake Relay Control Kit used in my Lulzbot Taz 6 Octopi setup, following the instructions provided by core-electronics.com.au/projects/time-lapsing-in-octoprint-properly. ...The cover attaches...

I made significant changes to the Prusa i3 PSU cover to accommodate a Raspberry Pi3 and a 1 Chanel Relay. The relay board is used to turn On and Off an additional LED light. The design is compatible with Prusa i3 MK2, MK2S and MMU models. One thing...

This is a relay box I created for my K40 laser, featuring separate inputs for the mains 240v accessories and the 5V circuits that power the control panel buttons and supply the relay. A recommended upgrade involves installing a removable connector...

**Cooler** * A USB Mini Desktop Fan can be controlled using a relay. **Filament Sensor** * A filament sensor can be added to automatically pause the print and run a GCode command to change the filament when it runs out. * The sensor should connect...

I made changes on the current Prusa i3 PSU cover to accommodate Raspberry Pi3 and 1 Chanel Relay. The relay board is used to turn On and Off the LED (additional). The design is compatible with Prusa i3 MK2, MK2S and MMU. One thing that you need to...