oo scale model railway

Perhaps my specific model of the C270 camera had some differences? Original "c270_hinge_M3_screw.stl" was missing a crucial constriction of the bore for the pin (as viewable in the original camera mount). The edge of it should form an inner lip for...

*** This model *** Double the fun with this new dual fidget ring! If you like the standard fidget ring and grew too accustomed to it, this one will give you some good alternative to play with. Be aware that you need to switch on support in your...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_case_wall_thickness = 1.6 custom_back_camera_corner_resolution = 8 custom_left_port_corner_resolution = 8 custom_corner_resolution = 8...

This model only cost 1 dollar because I am only pricing the topper and Star mount, the rest is free with the purchase. This is a pixel tree mount to build an eighteen string 216 degree pixels tree. Height can be up to 5 feet. The base design is...

My original plan was to also model a strap clip for the bottom of the mount, but I found that it was unnecessary, as the entire thing can be attached directly to the head strap and head pad with a velcro strap. I used a couple of long velcro cable...

The most common ones used for model rockets were very pricey and hard to find in bulk. I did some research online and found a couple of people having success with pencil graphite, so I started experimenting using an 18V drill battery as my power...

This allows the flow rate to be tweaked only for the detailed layers [as described here](https://support.ultimaker.com/hc/en-us/articles/360013370140-How-to-adjust-print-settings-of-a-part-of-my-model-in-Ultimaker-Cura). Update 4/10/2022 (v4.2):...

The rest of the modeling process was fairly straightforward, but I did end up printing 3 slightly different iterations of the design. Two were due to tolerance issues between the left and right sides fitting together. The third was to add a hole at...

You will have to remix the model and add new screw holes into them, or just drill them manually.. for now until I release the new version of the bipedal legs this Christmas Keep in mind that you also need 50mm M3 screws with nuts to hold the Size B...

There is not a real place for the buttons, but hotglue eliminates hours of 3d modelling, at least for me, and works well enough. This is a WIP so take as it is. For the wiring it's quite straightforward, take the 2 external potentiometer pins an...

As far as assembly is concerned, it's all pretty self-explanatory when you see the models, but here are a few tricks: Use as little wire as possible, but make sure you use good wire. The wires run from the grip and back, across the side of the...

Tools Hex wrench 2mm and Mmm...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 custom_corner_resolution = 8 stencil_drawing =...

The SATA power cables were custom made, from a stock Molex to SATA power cable cut down to 10cm and re-terminated with the 4 pin 2.54mm pitch JST XT connectors which the Odroid H2 has on board.SourceSource FreeCAD models:...

After, place switches randomly throughout the plate and test that the switches are able to return to their top position once pressed down.If the plate doesn't fit in the case, you may want to trim the outer tabs with flush cutters, or file it down.If...

### Outline Points and Rotations ```python outline_points_x[] = [-12,-18,-30,50] outline_points_y[] = [4,6,-32,56]\nstencil_rotation = 0 ``` These lines specify the x-coordinates and y-coordinates of specific points on the iPhone model. In this...

Subscribe Now! A very good model from LSMiniatures. Remixed to support free to do timelapse. https://www.youtube.com/watch?v=3NDJFnoX_3g <a href="https://www.youtube.com/watch?v=3NDJFnoX_3g"><img...

In Terms of Parts, I Used the Donor Guitar, Pulled It All Apart, Then I Photocopied It and Began Modeling. I Had to Reduce the Body by 97% to Get It to Fit on My CR-10 Because It Said It Had a 300x300x400 High Build Area But the Reality Was a...

Water cooled esc's are easy off the shelf for model boats etc and I may build enough space for a cheap (solar fountain type) water pump in the bottom. This could then feed the esc and also a water cooled motor plate. I also have a retro styled...

I recommend using a shorter heat sink and/or a fanBe sure to choose a fan size that will not interfere with the height of your heat sinkFilament sensor fits without issueBondtech extruder fits without issueOnly other fitment issues I have heard have...

Lastly, 5) It's ideal that any new design incorporates adaptability tailored towards various unique setups ensuring optimal calibration results across differing conditions allowing me customize freely as I work alongside other solutions which prove...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_left_port_corner_radius = 5 custom_right_port_corner_radius = 5 custom_phone_width = 100 custom_bottom_port_corner_radius = 5...

Cheers. Print Settings Printer: D-Bot Rafts: No Supports: No Infill: 20% Rectlinear Filament: DASFILAMENT PETG Trans Blue / Trans Green Notes: You need: a heatbed because of the big surface of the model A coolerfan for the threads Category:...

... Norrick      Details: Gravemaw is standing around 145mm tall on a 60mm customized base. The model is multiple parts, the file contains: 1 x Body 4 x Arms 2 x ½ tongue parts 1 x Intestine 1x Customized 60mm base. ... Support Version Included

This requires a solid fill model where only the walls are printed. Several changes were made to the CR-3D C8.1 design, including re-engineering the STL file and making ergonomic tweaks based on user feedback. The sides have been extended back to...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 0 custom_corner_resolution = 8 stencil_drawing =...

I haven't printed it yet, but the OpenSCAD model turned out pretty well. See the additional .scad file, .stl and the explanatory symbols image. The original bezel is dark grey with a textured interior except for the plinth and label obrounds. This...

It will be a lot easier for me to fix a problem than for you to re-model a part. Designing my first blaster has generally been a fun experience, a bit more difficult than I thought it would be though! Stock mounts and magwells were the most...

Check out my compatible Cable Hook. Also check out the <a href="https://www.thingiverse.com/tag:modular_mount">#modular_mount</a> and <a href="https://www.thingiverse.com/tag:MMs">#MMs</a> tags to find compatible...

Tensegrity model maintaining stability with one single wire.Materials needed:0.5 mm nylon wire7x M3 nuts7x M3x10 mm Allen screws (longer ones were cut to the right size)wooden plank of about 55 cm2x 50 mm wood nailsThe spiral parts are designed to be...