pangolin 3d model

Both have their own challenges and I'm just working through modelling them both to see which one is going to be the more viable one to do. ...I fear the chest plate on robocop would be pretty hard in so many pieces, whereas the T-800 could be done in...

If you like to print without supports pay attention to the Pocket Knife model: thingiverse.com/thing:4774553 Thank you for every review, like and donation, It motivates and helps to implement new projects! - Теперь возможно открыть лезвие...

[Medium Sized Model - 25mm base]   An automaton from the continent of Edrador. Wreathe is a “Soulforged” an artificial construct imbued with the soul of a forgotten citizen of the Anshani Empire. His past life is far beyond his memory, and such a...

[Medium Sized Model - 25mm base]   A Half-Elf Sorceress from Havenmond, Orstina is well travelled across Tharador, having done her studies in Brightstone’s Bruderland College. She now is temporarily teaching as a Professor of Transferrence at Ardris,...

[Two Medium Sized Models - 25mm bases]   A young artificer from Baldur forced to flee because of her homeland’s militant approach to magic and magic users. Em is a promising and keen student who was given the opportunity to study under a scholarship,...

Create a customized version of the Thingiverse model (http://www.thingiverse.com/thing:287025) using Customizer! ...Customize the options as follows: panel shape=1,...

* Compatible with very efficient common fan duct model. Cons: * Extruder heatsink removal mandatory. * Extruder cooling fan has not been added yet. * Can run into left Z-axis rod coupling during X-axis homing in certain situations (sensor wiggles...

The base shape I looked through Tinkercad's generators and discovered Cog Ring 2 by Yoda Wars, which I used as a model. The walls did not need to be very thick, so I chose an outer diameter of 14 mm to have 1 mm thick walls. Cog Ring 2 has a bulging...

There is also a Hotwheels variant of LB Huracan but I don't have that car so I can't make accurate holes to fit that specific model. If you have the Hotwheels variant, I could make another base to fit it. I need the length and width of the car...

This is the version I have used for my own model. 6. <b>horizontal fence.</b> This is the 4 sections of fence set up to print flat. (untested) 7. <b>steps</b> The steps print in one piece. I found I needed to slow my printer down in order to get a...

##You will need: - two MGN12 linear rails 400 mm long with MGN12H blocks - about 16 M4 hammerhead T-nuts (quantity depends on the required rigidity) - the same amount of M4x12mm flat head countersunk screws - about 16 M3x8mm socket head cap screws...

...Finally wound up getting it to work by reducing the poly count in both models drastically and adjusting the alignment until the intersection resulted in a usable part. * Add a box in MeshMixer, adjust the dimensions to create a backing for the map.

As seen in the images, one of the screws is different, instead of those marks they have a continuous line (4 blue and one yellow), it is a previous model that I have reused, at the appropriate height I inserted a piece of filament from another color...

EZABL added to a new model - the BreEZy-ABL V2.2. BrEZy-ABL V2.2 has a reinforced EZABL mount that connects to the air channel and a wider collar to better fit the fixing nut. (thanks to Stegolin for helping out here) V1.1 has a bigger clearance...

This model is approximately what we saw it can be printed in two halves and glued together. We both agree this is extremely close to what it looked like. Klamath Falls is home to Kingsley Field, the 173rd fighter wing, a F15 and soon a F22 base which...

This is compatible with 2010 - 2016 Panamera models (970.1 and 970.2) and is designed for the Samsung Galaxy S22 Ultra with [Protective...

I have included an optional spacer STL model for taking the place of the touch screen digitizer glass. I found this display unit very useful for setting up and debugging Raspberry Pies. Well worth the ~$40 to build without touch panel. Note there...

Give me a 🧡 if you like my work.This is an improved version of Knife Bow Stand: better parametric formulas, improved stand using sand as stability weight.CreditsMichael Whitley: Thank you very much for publishing model of Chef's Knife, which made it...

IMPORTANT NOTE ABOUT PRINT SETTINGS: I strongly recomend a 0.15mm layer height for these parts - especially the spacer washers, as they are modeled with thicknesses in increments of 0.15mm. Using a different layer height may affect these very thin...

I don't have one (yet)So I printed one and find some things I want to do better such as the bearing, they are relatively expensive to the whole printed model, so I want them to work properly. I made the center a little bigger and outer bearing ring...

Starting from an STL model of the left lens, build a parametric frame for your glasses. Using a hinge design by u:<a href="https://www.thingiverse.com/ericsko/designs">erickso</a> that I further reinforced, as well as his temple design (from <a...

&nbsp;It functions as the original Marushin model intended, with the rear trigger sear catching the first hammer sear, then transferring to the second forward hammer sear after releasing the trigger. &nbsp;Failure of the sears can result in the...

Finally, after making several designs that interfered with something I hadn't modeled or were too tall, I have a working mount for the Zesty Nimble on SeeMeCNC's HE280/Rostock Max v3 hotend/printer. Step file included, once I get my nimble, I'll...

The holes are placed on the two halves of the hinge slightly offset from each other so that the bolts do not touch when the box closes, avoiding extra bolt cutting.\r\n\r\nThe box is a low-security model used in the office to collect suggestions or...

english home battery case design for sjrc f11s is compatible with other f11 models, i recommend printing the main body vertically and the side flaps putting print holders is the only place needed project for those who want to mount their battery for...

I originally was going to print some of [these](https://www.thingiverse.com/thing:4725817/), but felt that the way they would sit in the rail was putting all the weight of the printer in to the arms of the model and not directly down in to the...

The length accommodates GoPro 5 and GoPro 4 models. With your thumb, you can raise and lower the focus stick, then press the shutter with your middle finger. These are significant improvements. This design is a GoPro tray for use with one to two...

Pull the models from there, although it turned out to be a leapfrog with blowing - I left the original "nozzle" of blowing, and drew my own top, so it is exported from STEP in parts ... ))) STL description: MintMount_base.stl - base for hex nuts...

Here's a link to the prototype turbine rotor I cnc machined many years ago: https://www.flickr.com/photos/steamboat_ed/albums/72157645304226559 Parts you'll need to finish the model include: A length of 3mm steel shaft for the turbine axle 8 M3 x...

This design is compatible with both the original & OLED model Nintendo Switch. Print settings: Use tree supports (on build plate only) when printing the PC case & display monitor. The files that require supports are named:...