pipeline drawing 3d models

This will also maybe give me a good surface to mount an endstop, which I have not started thinking about but came to mind while drawing this last night. Part has been updated. Going to work on the "handle" part now but that may end up just being a...

Some additional materials needed: - 12vDC SPST rectangular rocker switch, 15x21 mm (refer to drawing) - 10k volume potentiometer with 17mm diam housing, shaft 6mm diam x 11.5mm long. - GX16-n microphone jack where n is number of pins. Minimum for...

In the sectional drawing, the left port is the reservoir, the center top port is the output, and the right port is the switched filling port. Here's a video of the assembly: https://youtu.be/_z327hESdH4 Before the cycle starts, the piston is in an...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_port_x_position = 20 custom_back_camera_corner_resolution = 8 stencil_horizontal_position = 50 custom_bottom_fillet_resolution = 8...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_size = 20 use_stencil = 0 stencil_shape = 4 stencil_size = 40 stencil_mirror = 0 custom_back_extra_port_x_size = 30...

Here is a concept drawing, machined from two pieces with barbed fittings embedded (these could also be female thread to accept nylon fittings). Stanley A Meyer WFC Single Cell Flow Through design can be used for nano bubble water air or mist etc...

Important information: Length of the carbon tubes, please see the attached drawing. Cutting them roughly is good enough, a milimeter more or less is not too much of a problem. Further tipps: as carbon rods have a rather low tolerance, they...

Currently, there are three models:Ebook Reader Holder (1x3):This was designed for my Kindle Oasis in its third-party case (if you want it for something thicker than ~15mm, let me know and I'll see about whipping you up a variation)1x3 footprint on...

Important information: Length of the carbon tubes, please see the attached drawing. Cutting them roughly is good enough, a milimeter more or less is not too much of a problem. Further tipps: as carbon rods have a rather low tolerance, they...

I first designed this product by drawing it. It was far less complicated to construct than anticipated, which was great because simplicity is key to a great invention. I went straight to prototyping using scissors, a ruler, cardboard, a hot glue...

If i can see real interest from people in this chassis i will prepare some new drawings, maybe renders, exploded views, sourced and printed part lists, assembling instructions or more photos or videos. I hope you like it and someone have the courage...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_corner_resolution = 8 custom_back_extra_port_y_position = 30 custom_top_port_corner_resolution = 8...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_port_x_position = 20 custom_back_camera_corner_resolution = 8 custom_bottom_fillet_resolution = 8 stencil_horizontal_position = 50...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_size = 20 custom_bottom_port_x_position = 20 custom_bottom_port_corner_resolution = 8 stencil_rotation = 0...

Take a look at the images for a terrible drawing of how it's all wired. 1. Start with side LED. Shove it in to the side piece. Add some heat shrink tubing to the leads so they aren't contacting each other. 2. Solder the 320 ohm resistor to the...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_port_x_position = 20 custom_back_camera_corner_resolution = 8 stencil_horizontal_position = 50 custom_bottom_fillet_resolution = 8...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 stencil_drawing =...

We do not create or discover art through reason alone; instead, we allow each creation its autonomy, knowing it speaks in the silent voice we call intuition, drawing its inspiration from what dwells deeper than rational insight and understanding. By...

Info: STL / DXF files, instructions and drawings will follow when the first prototype with AR15 grip and mount for the yet to be developed folding stock with magnetic lock has reached a development stage for you to test. The STL files available...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_phone_thickness = 10 custom_back_camera_x_position = 0 stencil_pattern_element_overlap = 0 custom_top_outer_edge_chamfer_radius = .6...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_extra_port_corner_radius = 5 custom_right_port_corner_radius = 5 custom_top_port_corner_resolution = 8 custom_top_port_corner_radius...

Connecting the servo to the 5V output on the NANO might not be a good idea because the servo may draw too much current and will most likely fry the board - maybe it's possible with these little ones but I haven't tried it yet. I would appreciate some...

This light draws 0.15A at 120V, 0.075A at 240V, 0.065A at 277V, 1.5A at 12V, or 0.75A at 24V.Versatility: The LEDBLT-18W is listed for use in United States and Canada. The unit carries an IP65 waterproof rating ensuring protection against ingress...

Added a box for the small one. 2019-11-09 update: added FreeCAD drawing. How I Designed This The box was done with...

The 3MF file includes reinforcement via modificators and tested print settings. Product information: English version, Czech version (including assembly instructions) Assembly manual: English version, Czech version Assembly video Rubber band You...

Hello you!I drew up a little binder clip also called paper clamp that makes use of a rubber band to clip in documents, notes, drawings and so on in your workshop, office or at home.The two parts of the clip are held together by one or several rubber...

In the corner of each technical drawing, there are the slicer settings I recommend for each of the parts.Gimbal adapter with rubber dampersThis is the part that attaches the gimbal to the locking element which is then used to attach the whole thing...

... At the point it closes, the text will start, always at the same position. To optimize exposure, the (modest) rattling will draw attention. ...If the text is upside down, reverse the following order of the port numbers 3-12 in the Arduino sketch.

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_case_wall_thickness = 1.6 custom_back_camera_corner_resolution = 8 custom_left_port_corner_resolution = 8 custom_corner_resolution = 8...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...