playground swing 3d models

I have not modeled any nut traps in the parts because I think they will weaken them so all bolts here just screw into the plastic. I believe the parts are thick enough that the bolts will not loosen but time will tell._ 1. Completely disassemble...

I considered adjusting the model, but decided to leave it as is. I'd rather have a more positive engagement that you can adjust to your liking, than end up with one that doesn't latch in place securely enough. ;)</p><p>I will leave this marked as a...

Its light and super stiff if printed in ABS 100% infill. Included are all the .STL files for all the models. The frame is quite light and stiff. I threw the frame over and over against a wall and from a 5th floor balcony and it survived...

Just copy your gcode to the same folder as the exe, run it, select the options you want and when you've confirmed your choice it will automatically open the first gcode in the same folder and write the temperature changes for you.Extract...

Winston sculpted reproduction of Schwarzenegger's face in several poses out of silicone, clay and plaster.[41] The sequences set in 2029 and the stop-motion scenes were developed by Fantasy II, a special effects company headed by Gene Warren...

If you are using ceiling pipes, I've modelled the right side of the pipes only. For the left side it will need to be mirrored in the slicer. The vents part is optional but I recommend glueing it to the roof. The vents piece can act as additional...

...Please check if they are valid for your model.Choice &amp; file prefixesABCDcap typeFXFXSFXEplainAAAbelt tensionBBBtyre inflationCDDall cap variants use the same gasketgasketGGGFitI have printed two dozens of variants during development of the caps.

head), I recommend staying in a 18-25 mm range for the thread length, to give yourself some margin.For my US friends using imperial, you can use #4 screws but you will need to adjust the nut parameter in the f3d file.Also, I think it doesn't leave...

The “NANO 1” model follows (support for matrix / hemera already published). in addition to the name and logo (grant it to me) they share the same "SUPPORT BASE" component as a fixed base, and with the quick release (only 2 screws) to adapt in the...

I have re-modeled them a bit and now there are only a few strings. None if you print them with a 0.12 layer height. Filament Dry Box Set (Updated 3/11/2021) This set of prints are designed for use with the following items to create a very slim...

&nbsp;&nbsp;ENGLISH-------------Only tested on T12-X, but can work on equivalent models with boxes of the same dimensionsI found my T12-X soldering station a little too bulky, the screen not very visible and too dark. I also wanted to have all the...

Slice your model in your desired software and save your gcode 3. Place the created gcode in the same folder in which you extracted the exe 4. Double click to run the exe 5. Type the number of the option you wish to use, for the towers included in...

This is a servo hinge setup for use with MIPRESIDENT's Iron Man Mark III helmet (http://www.thingiverse.com/thing:260152). You can see my final build here: http://www.thingiverse.com/make:286759 And a video of it in use here:...

There seem to be quite some error margin in production, if your model is a bit too big to fit, just sand off maybe .5 mm from the sides to make it fit.Completely(!) remove any filament remains inside the two enclosure parts.Fit servo into upper half...

And Happy Printing!-------------------------------------------------Originally designed in Fusion 360 and printed with Prusa Mini+&nbsp;THIS MODEL IS UNDER CC (Creative Commons) LICENCE.&nbsp;Note: The DO NOT EAT sign might not print properly due to...

Moreover….Sitag astonished me a lot because actually….they continue to make and sell the same model: the famous “Sitag Reality”…which costs now around 700€ !!!Therefore, I decided to try a repair with my engineering skills and a big dose of...

Just go on Amazon or Ebay and get a metal vice and then bolt it down securely on your workbench.The specs for this little guy are:40mm jaw opening20mm jaw widththroat depth 12mmThanks to a metal screw (M6x60) and an M6 metal nut as inlay, it is...

The “NANO 1” model follows (support for matrix / hemera already published). in addition to the name and logo (grant it to me) they share the same "SUPPORT BASE" component as a fixed base, and with the quick release (only 2 screws) to adapt in the...

If the diameter of the mounting holes (see diameters in the image above) of your driver is (slightly) different you can simply scale the entire model (all parts) in your favorite slicing app to make it fit. <b>PRINTING / ASSEMBLY. </b>This...

A customized version of this Thingiverse model (http://www.thingiverse.com/thing:46884) was created using Customizer. ...The STL file options include: qr_rotate=0, add_sub=2, hole_r=10, hole_y=0, hole_x=30, corner_num=1, qr_thickness=5,...

If your name is not Matt, then there is a template attached in the model files called “Name_Plate_Template”. If you wish to add your own name to this template, open the attached file called <code>Name_Plate_Template.step</code> in a CAD software of...

The pictures and model views all show the right hand frame. Most of the parts print without supports except for the inside half of the spool, handle post and reel frame that require “supports on build plate only”. I also use 100% infill for all...

... this design, but don't want the silly text on the knife strip? Check out the modular version! Modular Wall-Mounted Magnetic Knife Strip

A few copies of it will be printed, for two reasons: cooling during print and as spare if some print fails. raketplattform överdel_xy0.4mm_z0.2mm_ELIXIR_ELIXIR_ELIXIR_ELIXIR_ELIXIR.3mf raketplattform...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_position = 0 custom_right_port_y_position = 0 custom_phone_thickness = 10 stencil_pattern_element_rotation = 0...

&nbsp;You may have to insert a custom hole for a usb lead depending on your mounting position, this could be done in the model, or via a drill after printing.You will need to do some tweaking to keep the led matrix against the grid. &nbsp;This can be...

I added some build notes below and a BOM which doesn't include screws, wires, connectors, etc., but has all major components.&nbsp;I planned to revisit this model and release a better version. However I have at least a year's worth of projects in...

4028 fan mount: Note this is modelled with internal supports in the top section of the duct to make it easier to print. Please remove these supports after printing. 4 x M3 32 mm (upper fan mount) 2 x M3 x 12 mm cap screws (lower fan mount) 6 x M3...

The files under Skycat17 (this one and a model of the Chrysler Building) are still available for download on Thingiverse. But I have no access to even see how many have downloaded or responded. The Tripod. The Phone Holder. All 3...

:DI put 3 holes in the top of the soap container where you can store your toothbrush or similar bathroom itemsI hope you enjoy the model and just try it out for yourself.I have written a description of how to make the soap here, which should give you...