r_e_r_f anycubic 3d models

I make these models for my own collection but I am always open to suggestions of content for models that cover the DC and Marvel universe as well as TV and film cult images e.g. Barbarella. so message me if you have any ideas . . As always enjoy the...

However, because we're working against fixed reference points, it's much easier to, e.g., raise the entire front rail a particular amount to help align it to the rear rail. Also be aware that installing the tool on the left rear rail requires...

To correct this situation simply replace it with a slightly weaker or shorter compression spring.\nPreparing the components:\nFirst, carefully print all of the required parts according to specified guidelines (i.e. base pieces, arm pieces, and cover...

The childproofing can then be achieved via the height :) But by the fact that you can take the knives straight out of the holder this should be well feasible.For households without children, the mounting is also suitable in drawers, doors or many...

...  You can make narrow cuts by using the dowel stops and setting the desired width directly on the scale.  For wider cuts, use the regular bottom stops and add the length of your spacer (e.g. ...250mm or 10") to the value displayed on the scale.

... I didn't do that. The model already holds up well and if you do not glue the pi-binding, you can, if appropriate, remove the sigma-binding system, e.g. B. ...to compare the bond lengths with other models (ethane / ethene (Ethylene) / benzene).

disclaimer: this robot barely works, please read the details down below before thinking about making this projectVideo: https://youtu.be/KbjHq6FzcFsthings needed:-resin printer-Adruino Micro/Uno/Leonardo or something similar-1.5mm drill bit to round...

... framework. I didn't do that. The model already holds very well and if you do not glue the pi-binding, you can, if appropriate, remove the sigma-binding system, e.g. B. to compare the bond lengths with other models (ethane / ethyne / benzene). ...

However, keep in mind that if you switch to metric units, you will likely want to adjust the board parameters accordingly (e.g., a 1/4 meter thick board might not be ideal). This model is simple enough that it can be rendered using the Thingiverse...

In addition, my E3D bracket allows quick changing of hot-ends (I have an array of hot-ends in both 3mm and 1.75mm styles, with nozzles with varying orifices - it takes about 10-20 minutes to swap the head and extruder, though it can'e be done while...

Eldritch tokens, clue tokens and a group of other tokens (e.i.: doom, rumor, omen, mystery, lead investigator and active expedition token) are accommodated here. 03. SMALL CARD TRAY: The tray with 4 sections for 4 different small cards: asset,...

ALL other SMART ENCLOSURE FILES (all list above) Files delivered to your e-mail Mainboard shipped with priority+tracked post (postage is included!) Please send 40EUR to my paypal: https://www.paypal.me/JKTechSI/40EUR Here is INFO & 3D files for...

When assembling the gate_4_b_x6 module on top of the wiring slot part (gate_3_b_x6, gate_3_a_x1, gate_3_e_x1, gate_3_d_x1), mark the holes with a Sharpie. This ensures accurate placement and reduces light leakage through the back of those pieces. I...

Measure time (ms) to move from one side to the other side at current speed Settings commands: D# Set direction forward (away from motor side)E# Set direction reverse (towards motor side) +# Increase speed with +5 (000-255)-# Decrease speed with -5...

You may want to have a referee who only accepts a fast enough spin (i.e. so fast that it's a blur). The person who achieves this in the shortest time wins. Knocking the spinner off the holder results in a time penalty. Be careful! Confessions of a...

E.G. a 15rpm at 6v would be good. I also had to get m1.6-0.35mm screws to mount the gearmotor. Since the only ones I could get quickly at a reasonable price were 6mm long, that's what I designed the gantry for, so that they can be snug without...

... objects to be placed at the same coordinates. Some slicers may still misplace supports (e.g., in Cura, uncheck "Ensure models are kept apart"). ...An all-in-one model of duct and supports has been added to ensure correct positioning in all slicers.

It will adhere to plastic just fine and does not require primer. e. allow everything to dry and reassemble the keyboard including the internal parts</p> <p>My other stuff (mostly Keyboards) <a...

This ability to sense and adjust input current also provides protection against voltage spikes and drops that can occur in electrical systems which would otherwise result in burning up or premature LED failure without it.Durability: The LEDWL series...

There should be a tight friction fit between the ID of the ArmBushing and the X rod - and a tight friction fit between the OD of the ArmBushing and the Prusa arm.Then tap the X rod into the ArmBushings (one on each side of the arm) with a mallet...

Here is [a link to my models in OnShape ](https://cad.onshape.com/documents/00593e55830305f7469b62da/w/c18d2b3e561f9a61444daf4b/e/4ef121b883b1b98caa778f39) so you can see how they were built # Other Components 1. The LED. I used 3mm LEDs that take...

The spacers need to be secured (i.e., bolted) tight so that they can maintain the distance from the bearing housing during operation. I chose to use two M4 bolts through the lower outer threaded holes of the housings. The hard part was to extend the...

-Archivo “Mordaza”: con este archivo podrá generar la mordaza que le permitirá sujetarlo a una superficie plana (p.e. una mesa). -Archivo “Seguimiento_visual”: este archivo son las piezas correspondientes al soporte para un dispositivo de...

I used an Axis P1214-E camera just because I had one laying around.I use OpenSCAD for my designs (because I'm a geek). I love it and will include files here for any models. Not these have not been cleaned up - they are a representation of a work in...

Because of all of the variables, i.e. plastic bending and cheap bearing tolerances, I had to just embrace *some* tsag and make the gap between the two layers a little larger. <b>An important note on printing</b> Use the feature of your slicer to...

&nbsp;After gluing, cut them flush.All custom PCB files are on github, and custom board(s) can be ordered via EasyEDA or OSHPark.Code for the sense board is also on github:https://github.com/lambtor/ArduinoTricorderHardware used, shown in one of the...

This starter kit includes a light switch paddle, a doorknob puller, and also a unique set of scent coded training fobs that make it easier for dogs to distinguish between multiple targets in a cluttered environment. Each of the pairs of colored...

There is a hole for a coax connecting wire (i.e. RG58, RG59,..) on each coil gap. You will need to print the four parts of the coil (A to D) and four pieces of the swallowtail block. The coil parts will be connected with the swallowtails. The holes...

It's enough to be stable but about as stable as the real deal at 100% size - i.e., it's a bit floppy and could be easily snapped in half. Not the sort of thing that you could use to securely hold things on a wall. You should attach it to a thicker...

Violence is never more than a heartbeat away.Keep your vehicles fueled!Stay in the fight!No support requiredResize for smaller or larger use. Designed on...