replicator 2 build plate 3d models
1155251 3d models found related to replicator 2 build plate.myminifactory
Locks the Replicator 2 build plate firm to overcome the common problem of corners lifting which results in prints warping (... ...and that can cause extruder jams).
cults3d
Locks the Replicator 2 build plate firm to overcome the common problem of corners lifting which results in prints warping (... ...and that can cause extruder jams).
thingiverse
Use this Thing to hold a dial gauge for levelling your replicator 2 build plate. I used this dial gauge http://www.amazon.co.uk/gp/product/B000LFYK0A/ref=oh_aui_detailpage_o05_s00?ie=UTF8&psc=1 and these 10x1mm magnets...
thingiverse
Locks the Replicator 2 build plate firm to overcome the common problem of corners lifting which results in prints warping (... and that can cause extruder jams). Instructions Print each file twice to make 4 x build plate stabilizers (i.e. the .stl's...
thingiverse
UPDATE: got a build plate waterjet from glass and it was one of two best upgrades to the Rep 2 and has had a substantial positive impact on my build experience. The other best is definitely this: http://www.thingiverse.com/thing:42250 ...
thingiverse
This a build plate leveller specifically designed for the MakerBot replicator 2
thingiverse
These are designed to be cut out either by hand or by CNC machine, bent (again either by hand or using a sheet metal brake), and then installed over the Replicator 2 build platform support arms.
thingiverse
a couple of weeks ago, our makerbot replicator 2 was returned from service with a broken build plate latch (see second photo). this didn't happen out of the blue, as this latch was already acting up before. the service firm assured us that they would...
thingiverse
I overheated my Replicator 2 aluminum heat sink one day and messed up my original fan mount. This one has a higher horizontal part to allow for more room for the spring loaded filament loaders, as well as holes to allow access to the fan mount...
thingiverse
Why not print a raft just once covering the entire build plate, permanently attached to the surface of my broken build plate? Then I could print anything and it would come right off. And it worked! Just clean your build plate and level it as well...
cults3d
Customizable Spring Footings for Replicator 2/2X Build Plate
thingiverse
Makerbot Replicator 2 Replacement 3/16" Glass Build Plate Adaptor Based on and similar to the adaptor that comes with P3-D's glass build plates.http://www.p3-d.com/products/glass-build-plate
thingiverse
... the lack of spring footings. This simple upgrade fixes this problem. UPDATE (Nov 14, 2013) Now customizable! Instructions Print three, unscrew the Replicator 2/2X build plate, install under each spring and re-install build plate and re-level.
thingiverse
... Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=129663 Instructions Using the following options: inner_height = 8 base_height = 2 base_diameter = 12 inner_diameter = 6 hole_diameter = 3.4
thingiverse
These are notches to make centering your Upgraded Glass Bed as easy as the original Acrylic Bed. As an added bonus they offer a customized look to your Rep2 when printed in your favorite color! ...
thingiverse
Customized version of http://www.thingiverse.com/thing:129663 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=129663 Instructions Using the following options:...
thingiverse
Customized version of http://www.thingiverse.com/thing:129663 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=129663 Instructions Using the following options:...
thingiverse
Customized version of http://www.thingiverse.com/thing:129663 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=129663 Instructions Using the following options:...
thingiverse
Customized version of http://www.thingiverse.com/thing:129663 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=129663 Instructions Using the following options:...
thingiverse
Customized version of http://www.thingiverse.com/thing:129663 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=129663 Instructions Using the following options:...
thingiverse
Practical upgrade for the Replicator 2, this one will improve the rigidity of your build platform - and hopefully improve the surface quality of your taller prints. The material is EVA Foam. You can buy sheets in a lot of places. I recommend 2 mm or...
prusaprinters
To enable the Heated Build Plate setting in the MakerBot Print software. You have to replace one file. First make a backup of the current "replicator2.json" (just zip it). And then replace the "replicator2.json" file. Win: C:\Program...
thingiverse
After heating my build plate I use a feeler gauge to set my nozzle height to .006" above the rear most leveling screw, set my indicator to zero, and level the front to screws in relation to the back most. With this block I can consistently get...
thingiverse
To enable the Heated Build Plate setting in the MakerBot Print software. You have to replace one file. First make a backup of the current "replicator2.json" (just zip it). And then replace the "replicator2.json" file. ... Win: C:\Program...
thingiverse
Woodsmoke made a super cool build plate leveler, but it was a bit small for the Replicator 2, so I stretched it! From Woodsmoke's original thing: Larger and more complex parts require greater accuracy in 3d printer calibration, especially with regard...
thingiverse
Yet another practical upgrade for the Replicator 2, this one will improve the rigidity of your build platform - and hopefully improve the surface quality of your taller prints. Only a few days after I got my Replicator 2 I began to notice that the...
myminifactory
Our build plate uses the whole build volume of your Replicator 2 or 2X, the plate is bigger than the original 2X HBP and so you have a more stable temperature at the side areas.The plate is "plug & print", that means you have not to solder or so. ....
thingiverse
IDE heated glass build plate system for the MakerBot Replicator 2 & 2X Compatibility: The IDE HBP System is compatible with every MakerBot Replicator 2 and Replicator 2X. You have to do no modifications on your device. What are the benefits? If you...
thingiverse
... I use a glass build plate. I like this because I believe the silicone will give up less z over time, it loves my glass and I don't run the risk of a random piece of fuzz catching some mystical Rep2 thermal and ending up gliding into the print job.