rust character models

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_corner_resolution = 8 stencil_horizontal_position = 50 custom_top_port_corner_resolution = 8 custom_back_camera_x_position = 0...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_mouse_ears = 0 pattern_line_thickness = 20 custom_bottom_port_corner_radius = 5 custom_back_camera_corner_resolution = 8...

See overview here for model comparisons: https://makezine.com/2014/11/22/review-airwolf-hd-hdx-and-hd2x-3d-printer/ The Airwolf APEX Software has pre compiled firmware included for all the HD series but the m500 command is disabled. The public...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_mouse_ears = 0 pattern_line_thickness = 20 custom_bottom_port_corner_radius = 5 custom_back_camera_corner_resolution = 8...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_mouse_ears = 0 pattern_line_thickness = 20 custom_bottom_port_corner_radius = 3 custom_back_camera_corner_resolution = 8...

I made a small update to it, adding the model with the included screw threads in the back, and ever since that update the thing is still there but returns a 404 error for everyone who isn't me. I've tried to get it to post, I contacted thingiverse...

My original plan was to also model a strap clip for the bottom of the mount, but I found that it was unnecessary, as the entire thing can be attached directly to the head strap and head pad with a velcro strap. I used a couple of long velcro cable...

The Aim of this project was to build a converter kit for my V2 model into a Core YX printer and by reusing as many original parts of Ender 3 v2 as possible. The second goal of this build was to keep the possibility of converting back the coreYX to...

From the original set I only did not try to model the chain gears since the chain consists of quite small parts and would be difficult to print accurately enough. On the other hand, I added many different gears to the original ones (12T, 24T). ...

It is possible that a future will make and upload a model of that piece. In the meantime, if anyone knows where to get suitable pads, please let me know. As I was saying, I started to hang them on the screw. Since the surface of the screw with the...

If you're using another fan make and model, make sure you check the polarity so it isn't reversed. If you don't have crimping tool you can just cut off the connector from the original fan and solder/splice it on. Print the 3 (4) parts. If you use...

This model is cheaper than the usb c version and charges the Oculus Quest perfectly. This greatly improves your playing time and you could even charge the battery while using it. One design came close to what I liked, but was made for a different...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_mirror = 0 stencil_drawing =...

This is the first 3-D model I have built from scratch and I was looking to get it done quickly. So, I kept it simple but did note that it wouldn't take much to add a few more amenities that would suit personal needs or desires. The router fits...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_mouse_ears = 0 pattern_line_thickness = 20 custom_bottom_port_corner_radius = 5 custom_back_camera_corner_resolution = 8...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_mirror = 0 stencil_drawing =...

May fit other Vixen equatorial mount models and clones such as: Vixen SP, SP-DX, GP-E, GP-DX Celestron CG-5 Synta EQ-4, EQ-5 Skywatcher EQ-4, EQ-5 Orion SkyView Pro Jinghua HD (Apogee Inc.) Or make your own brackets for your mount to fit the motor...

They were sold to me as "boat nails", feel free to substitute them for something else and adjust the model accordingly. For the spark gap I used a couple of bits of single stranded wire, these can be substituted for something else, multi-strand...

(Only one at this point as I only have the Canon to model from) 3.Tubes:: Choice of no tube, 13mm effective, short tube 21mm effective, long tube 31mm effective, long plus short tube 39mm effective, customised. 5.<strong>Lens Mount:</strong> 52mm...

I added the resistor, pot, and a switch to the power supply control box, then modeled and printed a knob for the potentiometer to hide the apprentice marks visible around where I put the pot through. Should fit any potentiometer with a 6mm shaft and...

Except for the Sunlu mount plate just lay the models flat. The Sunlu mount plate I printed standing upright - even without support (although some minor bridging is needed, but that was no problem)</p><p>As mentioned above, the hygrometers are...

The model can accommodate slightly larger and smaller sizes as is. To fit your doorknob you may either scale the STL file before printing (measure your doorknob diameter D and scale by D/54), or adjust the parameters in OpenSCAD, render (F6), save...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

The model is optimized for the connectors shown on the pictures. Super glue/cyano acrylate/any other transparent fast setting glue which adheres to your filament. Wire (should be thick enough for 700 mA and thin enough to fit into the carrier ...

... with the not dampened stepper motor. Ein von Martin Majewski (@martinjmajewski) gepostetes Video am 5. Nov 2016 um 4:50 Uhr Update 3: I removed the V1 models as they seemed to have some issues. ... V2 is the most current and best working version.

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_right_port_y_position = 0 custom_top_port_corner_radius = 5 custom_left_port_length = 50 pattern_element_rotation = 0...

And get your supports in order first, the models need a relatively precise and flat supported surfaces. <font size="3">The modification uses many parts from the original setup, but the PTFE tube must be cut, making this a non-reversable mod...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_fillet_radius = 1.6 custom_top_port_x_position = -10 use_mouse_ears = 0 custom_bottom_port_x_position = 20...

...The design is optimized for the given print orientation - no need to rotate the STL model.You will also need two of the strain relief clips, which I have provided as a separate project.Assembly6 pieces of M3 nuts have to be pressed into the plastic.

... find sellers on Amazon.com or Aliexpress.com. This is still a working project. I will update the bill of materials I used, add more models for RPi 3, and sensors when they are done. ...If you have any comments or suggestions, please let me know.