scale modelling tools

Read the print instructions for some tips and tricks to print this model and to find out the rules of the game. Print instructionsHow to print The dart For one dart you will need 1 dart "core", 2 flaps and a round 10X5mm magnet. The flaps need to be...

This model is designed for pla/pet-g which does not shrink. 2) print in the orientation show in the pictures. While this does not give you 90° opposition for force vs layer lines, it does give you about 45° which is much better than 0° printing with...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 custom_corner_resolution = 8 stencil_drawing =...

Once printed make sure you clean the model up and pay particular attention to the mating surfaces of the front and back parts. They need to be smooth with no excess lumps of plastic. Any lumps could stop the parts fitting together properly. The...

If you still want to print your own loc line, I used the models from [MinyMan644](https://www.thingiverse.com/MinyMan644) found here -> [Loc-Line Fittings (1/4", 1/2" and 3/4")](https://www.thingiverse.com/thing:3268462). I strongly recommend...

IMPORTANT INFO REGARDING ARRMA 6s REAR HUBS: There are basically two versions of the Arrma 6s rear hub between all the 6s models (36mm wide and 45mm wide). <b>The recommended version are the hub parts used in the 6s Kraton/Notorious/Outcast which...

V1 arm is fine too, but there is a risk of collision with some models of head in very rare cases of high and wide prints prepare all parts power off the printer UNPLUG POWER CABLE! disconnect low voltage connector (2 wires) unscrew PSU from the...

Because of the simple geometry of the Box and the Pieces, these modest settings produce a very nice model in a relatively short print time. Please Note: Although I have not provided the solution here, I will respond to personal Thingiverse messages...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_left_port_corner_radius = 5 custom_right_port_corner_radius = 5 custom_phone_width = 100 custom_bottom_port_corner_radius = 5...

Yes, there's an actual tank model underneath all the nonsense; it's just badly covered over since I built a spacefuture tank around it. I used a different source for my sponson lascannon; the sponson mount is from Seb's Sicaran proxy, so any of its...

I modeled this in Fusion 360, and you can find the source files as well as IGES included. I printed it in PETG since that's what was in the printer. The infill was 30% with three solid layers. ... Print Settings: Printer Brand: MakerGear Printer: M2...

I will upload my attempts, but I advise only using them for modeling purposes only, or if you can get them machined out of aluminum or something. Only then will they be strong enough.</p> <p>If your stem is too low or your cable housing is too short,...

This also means that if you wanted to try to build a GoN NERD/NERD TKL, H87a, or the Kprepublic XD87 should all be able to fit - possibly with some small customization to the model. More to come as I sort this out, but the files themselves are ready...

OK, this isn't a model but rather a gcode script to facilitate automated cold pulls to clear out your nozzle. I use it all the time on my Ender 3 and thought others might get some good use from it as well. **What is a cold pull?** A cold pull is...

Wled ist eine Opensource Software von Aircookie, schaue hier : https://github.com/Aircoookie/WLED Du brauchst dafür die Lampe, die gedruckten Teile: 1x Deckel 1x Fuß Gibt es hier zum Doownload: https://cults3d.com/de/modell-3d/haus/test-leon75 Ein...

Let me know what I did wrong so it can be improved in future models. This thing is a work in progress. More photos, video, and thing files will be uploaded as they're made. The idea here is to make your own modifications or create new versions and...

Anser from Niklas: Hi Bas, take a look at Stefan’s video about filament drying, I learned a lot: https://www.youtube.com/watch?v=eqQRN9TUw08 You do need an active dryer, not just desiccant, but your Esun dryer might work (don’t know the model). Were...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

Not a problem with a well-tuned MK3S+.&nbsp; &nbsp; The box was printed usingFilament &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp;...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_corner_resolution = 8 stencil_horizontal_position = 50 custom_back_camera_x_position = 0 custom_top_port_corner_resolution = 8...

My Fusion 360 CAD model has 0.09mm of axial clearance so the printed threads should effortlessly spin together. Extruding over 0.09mm will make it extremely difficult to twist the nut and bolt together using fingers, so just reprint both parts with...

It is not intended to print and snap together but to model it in tinkercad via importing the object and duplicating it. I designed the battery mount to be installed over the forward bottle holder. I'm expecting to utilize stainless steel hose...

My girlfriend and I both need extras to be placed at our bed, (though slightly dimmer)So all in all, this turned out to be one of my best projects yet! A huge success!Future upgrades:I'd probably switch the Trinket to an ATTiny85 for a more low power...

The Sketchup model for all these pieces is included as well. Post-Printing Assembly Once you have the desired top, middle, and bottom pieces printed, place the SLC main board into the middle piece, then flip it over and press the LCD into the...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

A wrench is used to unscrew the end caps for relamping the fixture, while some competitive models require the “tap and knock off” method to loosen the end cap. 7. Explosion proof, impact and heat resistant Pyrex tubes provide lamp protection.Superior...

... clean it up. &nbsp;Pictured below are the on edge views of the dove tale design and the individual prints used in the above picture.If you decide to model your socket or light switch cover, the dove tail profile I used is shown below (units in mm).

PLEASE WATCH &nbsp;THE HOW TO VIDEO ON THE BOTTOM OF THE PAGE!!There is a very important step many people miss out on and like that the Lifesaver is not correctly &nbsp;mounted into the case and will fall out eventually.The upper and lower lip needs...

Issues that I have with the design: In hand, the phone with my case (Model brand Apple silicone clone) on it fits snug. I can shake it vigorously upside-down and the phone doesn't fall out. However, After strapping it to the stem, the mount develops...