seemecnc rostock max v2 3d models

LED arm for SeeMeCNC Rostock Max V2. ...Clips on 1" x 1" T Slot and curves around the outside of the print bed.

LED arm for SeeMeCNC Rostock Max V2. ...Clips on 1" x 1" T Slot and curves around the outside of the print bed.

After building my SeeMeCNC Rostock Max V2, I had trouble threading the filament through the top into the small hole and down to the cold end, It wasn't hard, just inconvenient to find the hole by touch since it was above my head. I made this funnel...

This is an adapter to mount the Mosaic Palette Scroll Wheel to a SeeMeCNC Rostock Max v2 printer. It can replace one of the existing side panels on the top of the printer. The cup itself has a helical cutout for the Scroll Wheel’s cable. The...

If you are not sure which to use go with try the following: **(1) 843XX Rostock Max v2 Assembly - 84310 Top Vertical Support-MM-Alt.stl** **(1) 843XX Rostock Max v2 Assembly - 84310 Top Vertical Support-Drawer-v2.stl** If you are waiting for the...

The build area is not a circle and doesn't resemble a circle. This is NOT the entire build area it leaves 1-2 CM on the outside. This object is much better at testing your X/Y/Z tower endstop calibration. Since it uses most of the printable...

This system utilizes the original Rambo and LCD controller mounting locations for installation of a [PanelDue 5"](https://www.duet3d.com/DuetAddons/PanelDue), [Duet 2](https://www.duet3d.com/DuetEthernet) (Wifi/Ethernet) and a [JohnSL FSR Endstop...

If you need more on the usage of the filter ring please see my build post at: http://forum.seemecnc.com/viewtopic.php?f=42&t=10409&p=93185#p93185 Print Settings Printer Brand: SeeMeCNC Printer: Rostock MAX Rafts: Doesn't Matter Supports: Doesn't...

This is a mount that I created to install the Orbiter V2.0 direct drive extruder on my SeeMeCNC Rostock Max V2. I had been using the Orbiter V1.5 extruder and really like the control that came from having direct drive extruder, but the mount was not...

A side panel for the SeeMeCNC Rostock Max V2 which fits a 92mm fan in the event you'd like to add some ventilation to your internal electronics. 

I have attached a kraken adapter that can be used with the factory seemecnc rostock max v2 and those of similar design. ...This is designed to allow the kraken to be mounted to the underside of the effector platform.

*Designed for Repables 476 "E3D v6 Mount for SeeMeCNC Rostock MAX v2," With Stock effector.* *Requires you to break one of the fan tabs off* May work with many other hotend mounts for the Rostock Max v2. height can be adjusted with washers. I used...

This is a mount for the Bondtech QR extruder to be used on a SeeMeCnc Rostock Max V2 using a square face frame extruder motor. Other mounts are for motors with a deep circurlar boss - which will not work for my printer. I printed this is ABS @225C...

This is useful if you want to make something to hang off the tabs on your SeeMeCNC Rostock Max v2 effector. There are three of these tabs on the effector at 120 degree angles. You just turn this model into a hole in TinkerCAD and slide it into your...

I designed these so that I could use the Smart Effector with the old, stock effector and arms from SeeMeCNC (rostock max v2). It also works with the machined aluminum effector from 713maker (see pics). I have E3D hotends but had to revert to the old...

This is a mounting plate designed to replace the Rambo mounting plate in the SeeMeCNC Rostock Max V2. I designed it to hold the DuetWiFi but it will probably work for the non-WiFi version as well. I haven't tested it though. I kept the same design of...

I have a SeeMeCNC Rostock Max V2 printer and I wanted to mount an LED light ring, E3d Cyclops, and David Crocker's Mini Differential IR height sensing board for 3D printers to the effector but they wouldn't all fit so I designed my own. This has 2...

I wanted an enclosure for my Rostock Max V4 and it was so new i couldn't find one already being shared on Thingiverse. So I started designing this one. most parts are 3d printed and bolt on using factory hardware. I am terrible at documenting...

This is a screen mount that fits onto the side of my SeeMeCNC Rostock Max V2. The side is covered by a blank on new printers. I removed the balnk and placed this screen mount in its place. It can also replace the LCD on the front of the printer. The...

... the .step file so you can add your own shenanigans. I hope this helps some of you. I printed this in ABS. Print Settings Printer Brand: SeeMeCNC Printer: Rostock MAX v2 Rafts: Doesn't Matter Supports: No Resolution: standard or fine Infill: 50%

This is a full enclosure for the SeeMeCNC Rostock Max V2. It has double doors on all three sides that swing open fully allowing easy access to the build area. I designed this enclosure to create a heated chamber and to (hopefully) capture the...

This thing is an idler adjuster for a SeeMeCNC Rostock Max v2. Note: This may fit the v1 and Orion printers. This adjuster makes tightening the belts on the Rostock Max v2 easier. It is designed to allow you to tighten the belts without putting...

Print Settings Printer Brand: SeeMeCNC Printer: Rostock MAX v2 Rafts: No Supports: No Resolution: .2mm layer with .5 nozzle Infill: Doesn't matter Notes: Printed in Microcenter Inland ABS at 240 with the bed at 90 on glue stick. I use a Prometheus...

This is an effector platform for a SeeMeCNC Rostock Max V2 printer. It houses an 80mm LED light ring, E3d Kracken, and David Crocker's Mini Differential IR height sensing board for 3D printers. This has 2 layer cooling fans blowing air to the...

This is a bracket that slips over top of one of the tabs on the SeeMeCNC Rostock Max v2 effector and adds a Cardan Joint for a flexible tube. You could blow air or in this case I am experimenting with adding a spot light to highlight the print...

This is a side panel for a SeeMeCNC Rostock Max v2 delta printer. You can use it to hide those dangling cables by adding a power module (plug) and USB panel mount cable. This example also includes venting for the power supply as well as a switch for...

... chamber at about 92F to 96F. Print Settings Printer Brand: SeeMeCNC Printer: Rostock MAX v2 Rafts: No Supports: Yes Resolution: .25 Infill: 40% Notes: Used ABS. ...Remove the supports from all the small holes both on the handle and the door parts.

This is a mount to install a dial indicator (I used the Pittsburgh 1" Digital Indicator from Harbor Freight) onto a SeeMeCNC Rostock Max V2. I used it to calibrate my Printer using the manual calibration tool here:...

Required hardware: 2x Nut M4 1x Bolt DIN 912, M4x35 1x Bolt DIN 912, M4x25 2x Nut M8 1x Washer M8 1x Threaded Rod M8x150 2x Ball Bearing 608 (I prefer the open version for this application) This is my remix (from...

Print Settings Printer Brand: SeeMeCNC Printer: Rostock MAX v2 Rafts: No Supports: No Resolution: .2mm layer with .4 nozzle Infill: 20% hexagonal Notes: I printed these with Microcenter Inland ABS on a glass bed with glue stick. I do have an...