seemecnc rostock max v2 3d models

I don't own the rights to this content and didn't create it, but I couldn't locate a file for it on Thingiverse, so I simply uploaded it. ...If anyone believes this is copyrighted material or something similar, please leave a comment and I'll remove it...

Here are some design elements to consider: Adding an optional side panel is a great way to enhance airflow and increase system efficiency, all while minimizing clutter. To facilitate easy installation, we're recommending a standard-sized slot for...

I designed a slimmer fan mount due to enclosure constraints. Three of these mounts are required because the fan blows just off to one side of the nozzle. It was designed specifically to work with this mount for the E3D V6. You can view it here:...

The spool holder's flat top ensured that every time the extruder drew in filament, the machine would experience a slight tug. ...By designing it this way, engineers eliminated the jerking motion that had been a recurring issue.

The spool holder's flat surface at the top prevented the extruder from smoothly pulling in filament, causing the machine to abruptly jerk each time. ...That issue was effectively resolved.

This clamp is designed to fit snugly against the glass plate, remaining low and flush to prevent interference with layer fans or the nozzle itself. It's built with the FSR Mount Plate in mind, as designed by Michael Hackney at...

Print it using a flexible material like ninjaflex, designed specifically for a snug fit within the filament guide hole. ...The structure seamlessly accommodates a 4mm diameter 1.75mm PVC bowden tube, ensuring smooth operation by eliminating sharp angles...

Adjusted the design to eliminate the external radius at the base, enabling a smoother printing process while also reorienting the part for improved accessibility.

<p>I got magball arms so tried putting the Duet SE carriage adapters straight on the Molded Cheapskate Carriages. Worked ok, but there was just too much flex with the carbon fiber arms. If you look at the 2nd photo it compares the joint locations for...

I was fed up with my wires constantly colliding with the ball bearings so I redirected them behind, through conduit for safer and neater performance than repeatedly rubbing against the ball bearings.

I grew tired of my wires constantly colliding with the ball bearings, so I redirected them to run safely behind the bearings via a sturdy conduit. ...This solution not only eliminated the risk of wear and tear but also kept the area clean and free from...

Designing Unique Hangers for the iRing Phone Grip/Kickstand Accessory. ...This is Version 1. Print Settings Printer Brand: SeeMeCNC Printer: Rostock MAX v2 Rafts: Unnecessary Supports: Available

The newer version uses three screws instead of four.\nPrinter Settings\nBrand: SeeMeCNC\nModel: Rostock MAX\nRaft Settings: Not Required\nSupports: None Needed\nResolution: 0.3mm Layer Height\nInfill Percentage: 15%\nNotes: This is a basic print, so...

Upgrade to the Rostock Max V2 Spool Holder for Enhanced Performance. This Three-Part System Includes a Robust Spool Holder and Threaded Cap, as well as an Adjustable Arm. ...The Spool Holder Features a Convenient 13X13 mm Square Hole that Easily...

Print Settings Printer Brand: SeeMeCNC Printer: Rostock MAX Rafts: Doesn't Matter Supports: No Infill: None Notes: Generally, I use ABS. Extruder: 230 Celsius Bed: 90 Celsius. Use a towel to cover the plate to decrease preheat time. Be sure to...

This is a custom RJ5 mount designed specifically for my Rostock Max Prometheus V2 Effector, available on Thingiverse at https://www.thingiverse.com/thing:2294232. ...It's engineered to complement the dual RJ45 breakout board from Amazon, listed as...

I replaced my Rostock Max V2 struder connection with a new EZR Struder, but the bolts were too long for the stock spacers. To reduce noise transmission up the solid attachment, I created some spacers from MakerFlex and added one between each hard...

I am currently switching over my Rostock Max V2 to carbon rods paired with Traxxas rod ends from the subpar arms that come standard. I modified the end effector to accept M3 mounting screws for secure attachment of the Traxxas rod ends. I strongly...

I created an easy-to-use adapter for attaching a Raspberry Pi at the back of my Rostock MAX's LCD screen.

I designed a dial indicator mount for my Rostock Max V2 to make configuring endstops and horizontal radius easier. The mount uses a low-cost dial indicator I bought on Amazon about a year ago; it has a roughly 30mm square of screws on the back that...

... for them. I shortened the leads from the LED ring and got rid of the quick connector on the power wires. Print Settings Printer Brand: Rostock Printer: Rostock Max V3 Supports: Yes Resolution: .15 Infill: 10% Notes: print with tabs facing up

Replaces a Rostock Max V2 side panel, allowing two DPS-1200FB server power supplies to seamlessly slot in and latch securely into place. Exhausting hot air directly out of the printer, these power supplies provide essential 12V and 24V rails. One...

Following a recent demand, I've created a spool rod tailored to the initial dimensions of the Rostock Max spool holder. ...Additionally, as per a specific request, this rod has been divided into two halves for enhanced convenience.

Rostock Max V1 Belt Tensioner A simple design of a belt tensioner for the rostock max V1, the online models did not satisfy me enough and I wanted to design this tensioner to get a good result, tension very well. Use a bolt lever to remove the...

...Mount this assembly onto your Rostock Max, ensuring clearances between the acrylic and skate. Secure the enclosure bottom brackets to the base and attach them to the acrylic using epoxy. Once cured, bolt the Acrylic to the enclosure bottom brackets.

I wanted to attach a camera to my Rostock Max V2 after upgrading with a Raspberry Pi 2 running OctoPrint. Since I only use this for remotely monitoring print jobs and not producing high-quality movies, I chose the Fosmon Technology "5.0 Megapixel USB...

Rostock Max v.2 Funnel Spins Filament from Spool Right Through Top Levels of Printer, Saving Valuable Time and Effort. Puzzling That This Feature Isn't Built into the Machine as a Standard Component .... ... This Ingenious Design was Crafted with...

Create an easy-to-print, 40mm fan duct for your Rostock Max 3D printer using OpenSCAD. ...Print it in PLA without needing support material, then secure it to the platform with three cable ties threaded through its top holes and air outlets (as shown in...

If you're using this design with a Rostock Max, be sure to push it to the bottom of the tower before initiating auto-calibration. Remixed from https://www.thingiverse.com/thing:1873032. ...(I highly recommend checking out Walter Hsiao's impressive...

A straightforward dial indicator mount is designed for Rostock MAX. Note that standard dial indicators have a 1/4" hole; this mount fits an M8 set screw and the indicator is drilled accordingly. The indicator isn't precisely centered but as close as...