skyscraper 2 low poly 3d model

... the original (within 0.5 mm). UPDATE 09/18/22: I found an error while modeling the TRX-1 chassis. Hole spacing for the M4 holes was off by 0.5 mm (should have completed the sub assembly first before posting - apologies!). ...It is fixed in V4.

If you fix it for print, make a Remix, or send me a model for re-upload it\n\nA seductress is a supernatural entity in folklore (traced back to medieval legend), that appears in dreams and takes the form of a woman in order to seduce men, usually...

... exception of the configured axle length parameter. If you're looking for a CAD model of the E3D 20T idler, you can find one here. ...Note: I patterned the tooth profile after the Gates belt, so it's probably not an exact match for the actual idler.

if you change it to 0.3 layer height, it won't need to print as fast but calculations will require the slicer to check.the tower increases perimeter print speed by 14mms every 1mm of z height causing an increase of 1mm3 of flow starting from 11mm3...

The case gives access to the Raspberry Pi 4's Ethernet port (for Ethernet adapter emulation), USB-A ports, USB-C connector for power, and MicroSD card slot.Case ModelsThe "Slim" case has room for the single DB-25 connector on the RaSCSI, but if you...

The main difference to the other models is that the tension in the middle is not created by a thread but by magnetism. Therefore the top is of course not as loadable as with a thread or a nylon string. But all the more interesting for the eye! After...

This set contains 12 heavily armoured Kingsguard Knights equipped with Greatswords   Presupported files are included for each model in both STL format and LYS (Lychee Slicer) format so you can rescale them if required.  Presupports have been created...

Use Instructions: Print the model Remove the heat sink, tubes, retaining screws, and any heater or thermistor -- only the hot block and heat break should remain If assembling, thread heat break onto hot block and finger tighten Turn hotend and jig...

... YOUR FRAME To protect your frame, most sharp metal edges have a plastic cover. Print RodEnd.stl to cover–up the sharp rod end. It's not in the photos, but you'll know where it goes. ###BIKE The bike in the model is a Banshee Prime V3. ...

One of the great benefits of printing on fabric, you get nice big volumes with very fast prints! Notes : - the dodecahedron must be scaled down to about 94% to fit on an MK3 bed. - [Done] I will cut in parts the models that don't fit...

I may update the model if requested to include captive nuts, but it was kept simple so it could be printed faster with no supports. The printer footprint will remain the same even though the case is a fair extension to the original; it doesn't...

TC 247 Steg's legacy continues to inspire new generations of soldiers, who look up to him as a role model and a symbol of what it means to be a true warrior. His story is one that will be remembered for years to come, a testament to the bravery and...

The current V4 STL files are now the most up-to-date versions, and I'm planning to model the actual airflow next. In the meantime, I'm testing things with temperature towers at various fan speeds to see what works best. Update: 2019-03-12: When...

This is my modelling of a puzzle by Goh Pit Khiam called "Square Fit". The task is simple - simply place all of the puzzle pieces into the 7x7 grid. The folding clamshell puzzle can happily hold all seven of the pieces even if you've not managed to...

The model was printed using filament from Goedis: Black PLA. I suggest 20% infill, a layer height of 0.20mm, 1.06% flow, a nozzle temperature of 215°, a heatbed temperature of 60°, and 60% cooling. You can try adjusting these settings based on your...

The customizer has the option of adding the swap tower, which it will do by default.For the best looking faceplate, you'll want the top infill area of the faceplate part of the model to be a single continuous solid print from one corner to the other,...

UPDATE 16/02/19: Finished bottom with folded legs, added more details to top, made body detachable from bottom (1mm gap around peg), made basic folded legs, and added all models to files. UPDATE 01/02/19: Made the plates detachable (1mm gap around...

Presupported in 32mm and 75mm scale [Medium Model Size] [Statblock included in our 5E Campaign: A Desperate Defense] A young student of ecology and biology from Belfrie’s University of Ardris. Cordelia spent much of her childhood in love with the...

I printed the model using a .2mm nozzle with 10% infill no supports at .1mm layer height on my unmodified ender 3 pro. After the print completed I taped the edges open edges of the mold and poured plaster of paris into the opening. I made sure...

However, it was the sculptor's personal touch that imbues the work with its sensitivity: the elegant proportions, unctuous modeling, and delicate execution (the finesse of the hands, laurel leaves, and strands of hair), the marble's perfect finish,...

We elected to use a simple pattern to give it more mounting points than a 3 hole punch provides while still making the procedure of replacing it easy for the law enforcement, and medical professionals using them in the coming months. additionally...

... operation on Outreach. With the Confederation's later advances in stealth technology and light weaponry, the Flea became a logical test platform for new prototypes. These performed well, which encouraged Earthwerks to refit several older models.

It's easier to download the model from there and work with it in your preferred format. Here are links to the materials I purchased for this build: [150mm...

I do not claim any responsibility for injuries that may result from using these models in a way that may cause injury. If you choose to use this product you are responsible for yourself. ... If you like this file please consider donating: ...

I also used a USB-B socket to make the connection cleaner, though you could run the cable directly in. How I Designed This Design This model was designed in Fusion 360 to be printed without supports, using the M600 command to insert magnets for a...

Not specifically a remix, but a bit of an enhancement, with a nod to the creator of the model I started with. I wanted to have a sweeping light effect for the lighthouse, so I've experimented with two options. In the course of doing this, developed...

This holder is made to fit for the Raspberry Pi 3 Model B: https://www.amazon.de/gp/product/B01CD5VC92/ref=oh_aui_search_detailpage?ie=UTF8&psc=1 It might fit other Raspberrys as well, but I'm not sure. The touchscreen I used was this one:...

I am certainly not the first to create this, and there are designs out there for other models which gave me the inspiration. I printed mine with eSUN PLA material on my Creality Ender 5 Pro which came out quite nice on the first print. I tend to...

[Medium Sized Model - 25mm Base] [Presupported in 32mm and 75mm scale]   A Sanguine Blood Mage who had lived in hermitude in the Sekatan mountains for a century. He preyed upon small groups of Wastewalkers or Watchers to sate his unceasing thirst for...

I did try fitting the Model B+ but it didn't fit. If the Pi Zero doesn't meet your needs, there are plenty of Pi 3 boxes available. *NOTES: A few users reported that they had to extend some wires because the GEN L board sits further forward, while...