spool and spindle 3d models

If this is going on a threader rod I would suggest to put the rod in a drill and run while holding spool holder and moving it back and forth just to clean out any burs and to help it spin freely. 10 - 15% infill should be plenty. If nuts are going...

Designed to allow a spool to be mounted to an 8mm metal rod by way of 608Z skateboard bearings.

You will need a lot of (at least 16) cable ties (assumed to be about 3.55mm in width, and 1.2mm in thickness), and then to print: 2x bearingbracket608.stl 4x lowerbracket.stl 8x rod.stl 2x halfspindle.stl (printbl.com spools seem to vary from 32mm to...

I have been using Jamie Laing’s Reels (https://www.thingiverse.com/thing:981617), the compact size is perfect for small quantities of components, but they don’t fit very well on my Pick and Place spindle, so I have created this small Center Spool...

Overhead filament spool support frame and centering spindle hubs for Rep-Rap 3-D printer

The spindle has integrated bearing mounts of course, and that's been designed to be friendly to printers (no curved bottoms: flat faces have been cut to make it work nicely with supports). Really, the biggest upside is that you don't have to use...

Included: Spool holder (In the picture I left the supports on for added strength) Adjustable filament trap to ensure no uncoiling happens Spindles for the two most common spool center hole sizes Filament guide with clips for either a top bar mount...

It's designed with a few key dimensions that will let you convert this from 8mm to 12mm to whatever wide dimensioned spools Instructions Built on my Thing-o-Matic with: Mk6 Stepstruder ReplicatorG 0040 / Sailfish 3mm ABS on 4mm nozzle 100% infill...

... because i wanted one that fit my Tronxy X5SA perfectly. ...This one has a mating diameter of 50mm and can handle spools up to 100mm wide. ...It should be installed on an M8 or smaller bolt that has a free length of 80mm (80mm from bolt head to nut).

This is a filament spool spindle designed to reduce the torque necessary to unspool filament while printing (on a Prusa i3 with 7mm threaded rod spool holder, or any other similar printer) -- give it a shot if you're having under-extrusion issues. As...

This is a filament spool spindle designed to reduce the torque necessary to unspool filament while printing (on a Prusa i3 with 7mm threaded rod spool holder, or any other similar printer) -- give it a shot if you're having under-extrusion issues....

You can change the diameter of the center hole to fit the shaft of your spool holder.

Spindle to replace the annoying threaded rod and nuts that come with Anet printers for the spool holder.

Same diameter as my SainSmart spool spindle, but with a shorter shoulder and 3.6" tall from shoulder to top for the Matter Hackers spools.

This is a spindle for 40mm spools. ... Combine with some Tinkertoys and you've got yourself a handy way to feed another color into your printer without removing existing spools. ... http://www.zheng3.com/2012/07/11/complexity-is-free/

... ... I added more curve to the top of the Spindle to reduce drag and eliminate the need for an extension on Hatchbox and Amazon_basics spools. ... Works with Spool Collars https://www.thingiverse.com/thing:3685330

When the filament spool has a core hole too small for the spindles on your printer this hooks on to the lip of the case and allows you to use spool with a small diameter hole. I ran into this when I bought some Taulman "Bridge" nylon filament. It is...

Filament Spool spindle (middle) for PLA filament spools. ... Center hole fits a 5/16" bolt.Our first publicly shared model.

... on the narrow stock spool holder. ... Quick design in Tinkercad helps to smooth those rotations and drastically reduce vibration. Designed to hold spool securely so it can't slide off the spindle, while allowing smooth rotation. ... Hope it helps.

Based on: Makerbottable Filament Spool v2.0 by Randy Young http://www.thingiverse.com/thing:8317 And based on: Printable Filament Spool Spindle for Reprap with holes by nickbontrager http://www.thingiverse.com/thing:10379 And based on: Mendel mount...

... just to swap spools? ... Tired of spools with different spindle sizes? This spool holder makes changing spools easy - just set the spool on the stand. Can be printed for as many spools as you need. The pictures show a four-spool version. ...

I had one machine that kept jerking the spindle just enough to make it slide off the edge (mainly when I wasn't paying attention to the spool putting it on or walking by). This design keeps it centered even if you put the spool on the holder when...

A spindle insert for filament spools, sized for use on 10-12mm dowel or rod. Prints without supports, no tools required in use. Reduces friction without needing a bearing. Great for use with flexible filament, which will stretch and under-extrude...

A spindle insert for filament spools, sized for use on 10-12mm dowel or rod. Prints without supports, no tools required in use. Reduces friction without needing a bearing. Great for use with flexible filament, which will stretch and under-extrude if...

... thought would use less plastic. I checked the gcode generated for version 2 and it looks like it uses more plastic then version 1 using 25% fill. I have not yet printed the version 2 design. ...So let me know how it works if you decide to print it.

So, I decided to make a couple of spindle cups that fit on each end of the sample spool holder and allow it to fit nicely onto my upgraded filament holder. You will need to print two of the cups and these are fitted to each side of the sample spool...

A spindle to hold our filament spools (thing:1146474) on our printers. One prints without support and one needs support. Print Settings Rafts: No ...

I wanted a filament spool spindle filler that I could fit on my K8200 without unscrewing the end screw and couldn't find anything on-line. Developed these hinged ones that you can use straight off the printer bed. Have only just printed, but used...

A spindle to hold spools of filament that was purchased from MonPrice to be used with the makerbot 2X Instructions Screws Used can be bought from McMasterhttp://www.mcmaster.com/#92463a403/=w2x3hu

Then carefully stretch the frame and slide out the spool that it comes with. You have to cut off both of the sleeves sticking out on the inside of the frame. In a photo I show one of them removed. Now print one of the bottom, one of the top, and one...