stl file repository 3d models

You can either adjust the tolerances using the Fusion360 file, or either sand the shaft down a little or wrap it in some teflon tape to make it fit.Assemble the electronicsCut off all but about 2 inches of the cord from the panel mount USB connector....

 I have included a pdf file for each folder with some printing instructions and printing time estimates.I bought all the RC stuff I used from the French AZ site. You will need2 batteries, one for each motor (easier); you need to decide how...

I have also attached the .STEP file to this design if anyone wants to re-mix this to work with the stock MK3s carriage. Or please, create your own better design and reference my design here as original idea as remix. 😀Basic Instructions:Print the...

Marble Floor Manufacturer: YURT BAY Collection: ALPHA Series Type: Bianco Marble 30 x 60 cm | 600 x 1200 Pixel Resolution Multi-Texture Design CORONA + V-RAY Materials 10 High-Definition Textures for Walls or Floors No Plug-In Required Archive...

You can print the covers of the individual letters with transparent filament or, as I now do, with white (matte white) filament (Sunlu PLA+), as this hides the LEDs and gives a much nicer light diffusion!Please pay attention to the order of the...

Thesis, Brigham Young University, December 2001. To learn more about compliant mechanisms in general, see the BYU Compliant Mechanisms Research (CMR) website or these books: Compliant Mechanisms, Handbook of Compliant Mechanisms  Intellectual...

This little ghost clip will help you and also will be very useful, let's say if you are reading a book or if you need a paper clip to separate your stuff it will help you, the ghosts clipper is a design that my partner and I made with 6.5 cm longer,...

It is a remix of the original spoolholder that uses printed roller arms and springs to press the spool down.To improve the stability of the arm, the profile was divided into two halves, the lower one containing the bushing and separated by a gap of...

In case you still observe a horizontal state, consider using a smaller magnet or increase the distance between magnet and reed contact.Files are updated and description is adjusted to v2.Items to re-print when updating: only Bucket and RainGaugeBase....

...You can download all the necessary files here. _Result: 800 mm/minute is realistic and the dimensions fit very well_ I measured the frequency of the spindle in Herz with the Spectroid app and converted it to RPM with calculate Hz x 60 seconds.

... some fake ones in PLA. I've added a print file for those. The TPU brakes are bigger (external diameter) and tighter (internal diameter). ...To print TPU without damaging your build plate put some kid's paper glue (the tube stick like a lipstick).

You can visualize the full assembled model and divide it into pieces in the slicer or just print what follows:Core 1-2Ring 1-26 x WingThe wings are the only parts that need supports, so I attached a support enforcer file: supports are placed in the...

Open the Routine_Generator.exe choose simple or advanced mode and follow the prompts to automatically generate a gcode routine to suit your needs, once it says "Successfully Generated Gcode!" simply go to the folder where you just ran...

... best to include feedback. So, if there are any changes to improve usability or stability, please let me know. For those, who want to remix parts by their selves, I added the Fusion 360 files to the download. Have fun with your Chiron! ...

For example, I have one of the first versions on my printer, which has not yet so well fitted (The screw holes are not 100% true voices rather 80% xD (I have long tuned filed until it was perfect)). So would not have been necessary a change to the...

You can print the covers of the individual letters with transparent filament or, as I now do, with white (matte white) filament (Sunlu PLA+), as this hides the LEDs and gives a much nicer light diffusion!Please pay attention to the order of the...

BODY: The files for the body have been created using a free model with the right license for comercial use, similar to this one as a base. I can't actually find the exact model. Looking for simplicity and low weight, a main body has been created...

I worked with Elana Wald on this project; you can find her clip version here (add link). Objective:With a partner, you will recreate your ghost clip using Solidworks.  You and your partner MUST have identical files that you create by collaborating on...

You will need to perform a PID tuning on your hotend after installation, and possibly specify a different thermistor type in your config file or firmware, depending on the new thermistor you use. Alternatively, you can reuse the old heater and...

With 250ml of developer you should be able to develop between 3 and 5 35mm 24 exposures rolls.This is not a conventional Paterson tank so please read the instructions on how to fill and drain the tank.I included the Inventor file so that you can edit...

Refer to the picture in step 2.Verify the chain is attached properly to all steps.Mechanism works but steps sometimes get stuck in the same spot(s)Check for burrs, strings, or blobs on the outer or inner track guides, and file them off.Generally hard...

... <p>Post your make!</p> <p>This is the first version. Please comment so i can improve it over time. Cheers Armin PS: I had to add a file from https://www.thingiverse.com/thing:13053 to make this thing visible. Category: 3D Printer Accessories

If you don't have it - either purchase it, or print/make it yourself - see https://www.thingiverse.com/thing:863257 Please, carefully read assembly and usage guide below. Source files are provided, so you can change design if you are using different...

... I apologize for being MIA. I have had some serious family stuff going on. I will not be able to make any changes to this for a little while. So I have uploaded the STEP file for anyone that would like to take a crack at making improvements.

Designed entirely in FreeCAD, I can post up the source files if anybody is interested (typing this+BOM has taken forever!). Also, as I post this, I've only just finished hooking it up and making it stand... so it's early days yet! Apologies for...

This helps keep the low profile as the fingers open and close. UPDATE: I've also posted a STEP format CAD file for this gripper Print Settings Printer Brand: MakerGear Printer: MakerGear M2 Supports: Yes Resolution: 0.2mm Infill: 20% Filament:...

Therefore stop needs to be inserted in the G-code.In prusa slicer inserting stop it adds the stop at the beginning of the layer so it should be added at the instance where magnets are being covered.Print and insert magnets. Make sure magnets polarity...

EN (Google translatror): When I came across https://www.thingiverse.com/thing:4160836 , a Christmas present was decided, but the author didn't really care about the project, although the discussion mentioned the missing lower half of the body, he...

ENGLISH Download all files: https://www.thingiverse.com/thing:5438282/zip ___________________________________________________________ I wanted to make a smoke absorber that was powerful enough and could quickly cool down an electronic board after...

 I just grabbed some generic full-size to Micro HDMI cables and all was well. Okay, let's talk assembly and parts!File naming note:  All the strut models have M or F in the name, to make it clearer which ones will connect.  The M parts have a...