straw model

I recommend 8 IKEA LADDA AA cells as they are amongst the best available anywhere (https://www.ikea.com/us/en/p/ladda-rechargeable-battery-70303876/):https://cults3d.com/en/3d-model/tool/aa-six-cell-battery-holder The one piece parts need a big...

No support is needed and would be very hard to remove because the support would be inside the model where the magnet eventually slides into. We are depending on bridging for the parts that would normally need support. I have given extra tolerance...

I 3D modelled and printed some end caps for it with Ninjaflex so it doesn't scuff up my walls. 4/10 update: I added some parts that hold a 3/8" steel rod in the middle of the pull up bar so it isn't just relying on the screw coupler to hold the...

If you need a lot more room (more than a few mm) you may need to update the model to scale it appropriately. (~$1 of filament)</li> </ol> <ol> <li>Light string or rope. Cut it about 5ft 6 inches, or just enough to make a loop on the elbows, running...

I do not own a BL Touch so this design was based on 3D models so definitely WIP. I have increased the thickness of the Duct mount to the base unit to make it even more robust on the LH duct. You may now need to use M3 x 10 mm to fix to the base unit....

If the diameter of the mounting holes (see diameters in the image above) of your driver is (slightly) different you can simply scale the entire model (all parts) in your favorite slicing app to make it fit. <b>PRINTING / ASSEMBLY. </b>This...

Http://www.Thingiverse.Com/Apps/Customizer/Run?Thing_id=507810 Instructions Using the Following Options: Custom_phone_width = 100 custom_bottom_fillet_resolution = 8 printer_tolerance = 0.4 stencil_vertical_position = 50 custom_case_pattern_thickness...

6) I don't provide holes in the model for the harness or for the charging connector. These are also variable. I happen to use an RCA jack for my charge connection and I just drilled a hole for the silicone insulated wires to exit. 7) I glue the...

Do not purchase unless spare parts are easy to get; not all parts are easy to CAD model or print. OEM replacement parts for the q905 can be found [here](https://www.hosim.com/collections/parts-for-q903).You can also take the OEM part number and...

Design Notes: All holes are designed on size, so for example a 4mm hole is modeled as 4mm. This makes it easy for me to make both a clearance hole and a hole to thread into since all of my hole always come out a fair bit small. I use a cheap set of...

A custom-made enclosure specifically designed for the Raspberry Pi computer assistant Assistant assistant A bespoke casing tailored to fit the Raspberry Pi device. assistant Created especially for the Raspberry Pi, this is a one-of-a-kind case. ...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 0 stencil_drawing =...

COMPATIBILITY ------------- This air assist fits the 20W "Vigotec VG-L7" laser, also sold as "KKmoon BX20" (2021 model). That's a diode laser with Ø15mm focus ring. The focus ring is 10mm high. ADJUSTABLE Z AXIS REQUIRED ...

Using a allen key also has a couple of smaller advantages, those being reducing the number of pieces in the model, while also providing the added benefit of acting as a keychain mount.The gadget is made up of a few common parts apart from the printed...

1 slot for a pair of Kitchen shears and 1 slot for a Honing/Sharpening Steel.I designed the model into 4 printable parts so this could be printed on smaller printers like the Prusa Mini. But this also makes for easier cleaning since the bottom and...

This is because it is a slide on design to limit the complexity of the model.&nbsp;&nbsp;INSTRUCTIONS:&nbsp;I tried my best to make this the simplest adjustable optic for nerf yet! As such it has only 3 parts that can easily be printed in under 2...

In Ultimaker Cura you first have to install the “Mesh Tools” extension which allows the “Split model into parts” action.Pneumatic tubes with outside diameter 3 mm are used. E.g. Festo PUN-H-3X0,5-NT. Locate the four holes in the housing and enlarge...

This brings the Muscle v2.0 advanced cooling system, originally designed primarily for Longer and Alphawise printers, to many more 3D printer models and users. I am even working on testing a custom X-axis mount plate for Prusa/Wanhao and other I3...

EX6 Arcade Fight Stick What started as just doing a few tweaks to an existing model turned into a near full redesign and a (almost) fully printable arcade/fight stick case platform; the EX6. Printable on the Ender 3 or any 200x200 printer. The...

If you decrease the size of the model, you will end up with less than 2 layers which might decrease the integrity of the maze. You should be OK increasing the size, but the maze walls may not fuse in the middle using 2 layers. You'll need to...

Cable clamps bolt to the Extruder mount bolts to keep the cabling tidy, which I've not used yet as I can currently only run 1 of the heaters at present (my A20M control board is a V4.1 model which doesnt have the components fitted to allow for dual...

If you don't want to mess with a PLA support, you could probably print this part in two separate objects.I provide you the Fusion 360 file, so you can customize and change the model according to your rail system. I strongly recommend you to...

# Introduction This is a remix of the Ender 3 HallON v3 Installation kit to fit a Micro Swiss Direct Drive set-up (recent models with additional screw holes on the left. Because I noticed that the hold of the sensor in the adapter gets loose after...

UPDATE 09.08.2022 •changed length for diffusor and mount from 10mm to 100mm •orientation changed for some models •added end cap UPDATE 12.08.2022 •added with diffusor / without diffusor comparison photo and electronics box wiring photo •added...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 custom_corner_resolution = 8 stencil_drawing =...

&nbsp;I have it installed on both my printers and it's really nize.MK3S and (+) versions of the adapter are unique to each model and not interchangeable.Both adapters drop in over the screw heads as shown and get trapped between the extruder body and...

----------------------------------------------- MATERIALS ------------------------------------------------------ - Raspberry Pi Model 3 B (This is what I used but really any micro-controller can work) - Breadboard - Mini-Breadboard - 10K Resistors...

AnyCubic Photon Heater with Optional Light Models for for the Left or Right panel For the fan I turned it around after I found it not blowing outward. Double Check You use the right top and back that go together. Don't do Like I did in the...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_port_length = 40 custom_top_port_length = 70 custom_top_port_corner_resolution = 8 stencil_size = 74 printer_tolerance = 0.4...

If you want to be able to focus it, you'll need a helicoid that maintains or falls below M42's register distance of 47.46mm at its shortest for your camera setup. Disclaimer: This model is offered AS-IS with no guarantee that it will print for you as...