swivel camera mount 3d models
428007 3d models found related to swivel camera mount.thingiverse
Voron 2.4 swivel camera mount, mounts on the 2020 extrusion before the doors. ... Use M3 mounting hardware.
thingiverse
Swivel camera mount. Uses 3/4" 6X32 machine screws. Hex nut snaps int the wing nut. Use super glue to hod firmly. ... Due to request, I added a 25,50,100 mm double ball.
thingiverse
Swiveling camera mount for the TAZ5. Print-in-Place base that slides onto aluminum bed tray, lock into position with a M3x5mm screw. Short (15mm) and Long (80mm) posts included... or find one from Thingiverse. Great for Octoprint! Keeps model...
thingiverse
So I decided to build my own that not only allowed me to mount such a camera, but also swivel it and also to mount it to the door of the 3D printer, so I could have a better front-on view and avoid the heat of the enclosed 3D printer. I always had...
youmagine
Actually being printed.Best result if printed with 0,3 layer and 35% infill3 perimeter suggested. ...Assembly video available here
cults3d
A front swiveling camera mount for Prusa i3 01-04-2015 UPDATED THE SUPPORT with the revision 2 and added the M6 Lever, refer to the picture for the lever installation Assembly videohttp://youtu.be/FqYquOGgjXg
thingiverse
A front swiveling camera mount for Prusa i3 01-04-2015 UPDATED THE SUPPORT with the revision 2 and added the M6 Lever, refer to the picture for the lever installation Assembly videohttp://youtu.be/FqYquOGgjXg Instructions Print all the parts at 0,3mm...
thingiverse
This is a swiveling camera mount for a Logitech C910. I removed the metal plate from the base of the camera, replacing it with this printed part and reusing the screws. It works just fine and I have no complaints in that regard. It's a bit clunky in...
thingiverse
Since unscrewing something everytime I have to open/close the front door I came up with a mount with an integrated hinge to swivel the mount and the camera away. ...The mount for the PS3 Eye camera that I have used is this one:...
prusaprinters
As I have also planned to add a acrylic front door it should be able to remove very quickly in order to open the door. Since unscrewing something everytime I have to open/close the front door I came up with a mount with an integrated hinge to swivel...
thingiverse
...Thread the servo wire through the channel on the side of the mount and mount the servo inside of the mount with the four bolts/nuts. Insert the case and servo wheel onto the servo. Connect the servo wire to R/C reciever with the servo wire extender.
thingiverse
A swivel tilt camera mount for D-Link WiFi cameras DCS-P6000 and DCS-8000. I designed it as an attachment for the Ender 3 and the mounting bracket fits the back side of the power supply and is attached using the two M4 screws. The mount could be...
thingiverse
This is a modified Camera Mount Swivel for _Camera Arm - Standard Tripod Mount_ `Thing 3095730`. Link to thing: https://www.thingiverse.com/thing:3095730 I found the existing one had too large of a radius on one end. This is great for getting a...
thingiverse
Give your Simplisafe outdoor camera manual swivel/pan capability. Limited tilt provided by existing magnetic mount that is attached to swivel. STL files and Fusion 360 files included. Sliced files use CURA standard print settings for PETG, 0.4mm...
thingiverse
My cameras do not rotate side to side, so i made this and they work well for my house. Hope others find them useful too. You will need to insert a .250 Dowell pin after print is complete. ... Print Settings Printer: Monoprice...
thingiverse
This is a Swing Arm for a camera mount which I modified to remove unnecessary overhang which produced failed prints (See photos)
thingiverse
2x M4 bolts 15mm needed 4040 and 4020 mounts added enjoy
thingiverse
I have designed a Swivel mount camera Arm/Holder for a TOP-301 IP Camera. http://www.banggood.com/720P-1_0MP-Mini-IP-Camera-ONVIF-2_8-12mm-Manual-Varifocal-Zoom-Lens-P2P-with-Bracket-Network-Camera-p-1047878.html Bolts used are M5 bolts,., see...
thingiverse
This is a camera mount for a Raspberry Pi camera (v2.1) and derivatives. May also fit the v1 cameras. I'm using it with a wide field of view camera (pictured, link:...
thingiverse
Allows easy modification of your AR Drone 2.0 forward-facing camera, to allow viewing angles from 90 straight up, to 90 straight down. Overenginerred design includes ~22 degree snap-to angles and ribbon cable guide. ...
cults3d
I got this idea from seeing two different Raspberry Pi Camera things. I got the top part from: http://www.thingiverse.com/thing:442063 and the bottom from: http://www.thingiverse.com/thing:605368 Did a bit of editing and here it is. ...
thingiverse
I got this idea from seeing two different Raspberry Pi Camera things. I got the top part from: http://www.thingiverse.com/thing:442063 and the bottom from:http://www.thingiverse.com/thing:605368 Did a bit of editing and here it is. I did...
thingiverse
Needed a web cam mount that was not restricted to only vertical up/down adjustments like the standard mount that comes with the Logitech C920 webcam. This is because I like to use two side by side monitors angled slightly. Thus mounting it on either...
thingiverse
Check out my complete upgrade, the AM8 Dual Bowden here Mount a Raspberry Pi camera to your Anet A8 with this lightweight, easy to print camera mount. Tilts and Swivels. ...What you will need: 2x m2 14mm bolts and nuts Mount your Pi using my Ramps/Pi...
thingiverse
... but otherwise easy to print. You need 4x M3 screws/T-nuts to mount the holders and 4 small screws to assemble the camera module. The assemble snaps into place on the holders and can be adjusted up/down. ... Design files: https://a360.co/3egIHWC
cults3d
... but otherwise easy to print. You need 4x M3 screws/T-nuts to mount the holders and 4 small screws to assemble the camera module. The assemble snaps into place on the holders and can be adjusted up/down. ... Design files: https://a360.co/3egIHWC
thingiverse
This is my design of a mount accessory for attaching a GoPro camera to the print bed of my Anycubic Mega X. Since this printer has an i3 design, the bed moves, making it harder to get a decent time-lapse without Octoprint an a dedicated webcam. ...
thingiverse
I found that the SwivelBall_Female_Base_3mm_Clip_v3_Unscaled.stl was non-manifold. The model looked ok when I loaded into my slicer, but once I sliced it the top part of the clip was missing such that the two sides where not attached. ...I re-exported...
thingiverse
This is identical to http://www.thingiverse.com/thing:203968, but with non-manifold faces fixed. ... It sliced/printed just fine for me on the first try with the "fine" setting in Simplify3D on my MakerGear M2 printer, no need to rotate or change...