turntable 3d scanner

Turntable, supported on 6mm balls (valid airsoft balls) driven by a stepper motor and controlled by Arduino whose purpose is the improvement of photometry app (QLONE) for 3d scanning, also valid for product display with a touch of dynamism.

... OpenScan V3 3D scanner. ...Designed to mount to a 28BYJ-48 stepper motor. See our blog post about the 3D scanner project! Blog post: http://www.theprotolab.com/2020/04/24/affordable-3d-scanner/ OpenScan V3: https://www.thingiverse.com/thing:2755968

This is a Turntable for the 3D Scanner FabScan with 12cm. ...A Interface for the stepper motor is integrated

This automated turntable helps lazy people like me to get nice scans with a David Structured-Light Scanner. The turntable in action: http://youtu.be/r2YUnTnl1cY VirtuMake is an Open-Source project. Please donate, if you like my work and want to keep...

Best, Bernhard This is an instruction to build a arduino based 3D-scanner turntable for small objects. Watch the video at: http://youtu.be/n9UiJGrGvfY You need: 1) An Arduino uno: https://www.sparkfun.com/products/11021 2) A stepper motor:...

This is a replacement turntable for the Matter and Form V1 3D Scanner. I purchased two of these scanners used and both had issues with the guide bearings. The pins they snap onto had been broken which resulted in the turntable having a silly amount...

This is a replacement turntable for the Matter and Form V1 3D Scanner. I purchased two of these scanners used and both had issues with the guide bearings. The pins they snap onto had been broken which resulted in the turntable having a silly amount...

When I printed the original design for the scanner (v6 was the state when I built it), I noticed that often the turntable was not secured and therefore was hard to rotate without moving out of place. ...But, using these simple grips to latch on anywhere...

When I printed the original design for the scanner (v6 was the state when I built it), I noticed that often the turntable was not secured and therefore was hard to rotate without moving out of place. ...But, using these simple grips to latch on anywhere...

Get the parts at Shapeways: https://www.shapeways.com/shops/virutmake?section=Turntable&s=0 Instructions Parts List 1) 3D-printed parts: https://www.shapeways.com/shops/virutmake?section=Turntable&s=0 2) A 360 Degree Servo:...

https://youtu.be/moVuucoa0N4 In particular, I have designed the turntable to adjust the distance and angle of the camera to reduce inconvenience of having to change the camera position when scanning small and large products. To save cost of...

Instructions More detailed assembly instructions can be found athttp://www.freeasinsteins.com/journal/2009/4/28/printable-parts-for-a-3d-scanner.html Hopefully, it\'s relatively intuitive. ...The page also includes basic descirption of how it would be...

These are printable parts for a 3D scanner turntable. The base has been designed to sit on top of a standard Nema 17 motor. The turntable plate and the modified ciclops gear are designed to fit on top of the base. ...

A turntable for a 3D scanner, etc. Designed to be printed with no supports, no brim, no raft, and minimal cleanup. Easy assembly, versatile - can be set up as 6-to-1 or 24-to-1. Can easily add stepper/servo motors, cams, etc. I intend to use...

After some research online, I've decided to modify the turntable to turn the 3D scanner around instead of the objects/people. The additional elements I've included in the design were the adjustable extension arm for the camera dolly, and also the...

After some research online, I've decided to modify the turntable to turn the 3D scanner around instead of the objects/people. The additional elements I've included in the design were the adjustable extension arm for the camera dolly, and also the...

As it's programmable in speed, it can be also used as a 3D Scaning turn table. just mount a Cake-Plate on top of it (no need to print, just glue or screw it!) Add some lube (silicone or the one you use for your printer). Finally just put some...

As it's programmable in speed, it can be also used as a 3D Scaning turn table. just mount a Cake-Plate on top of it (no need to print, just glue or screw it!) Add some lube (silicone or the one you use for your printer). Finally just put some...

Added a d-shaft locking bolt/nut mounting solution to prevent slipping of the plate while turning. ...

Here we have a cellphone scanner turntable or what ever you use for making photos to get it into a 3D model. Simple and easy to print and to use. If you wanna turn it by yourself: use the "kurbel" (sorry i am german) In my case, a motor is...

3D scanner turntable This minimalist turntable can be used for 3D photo scans. The object to be scanned is placed on the plate and can be photographed from all sides by simply turning the crank. Using the appropriate software, the images can be...

3D scanner turntable This minimalist turntable can be used for 3D photo scans. The object to be scanned is placed on the plate and can be photographed from all sides by simply turning the crank. Using the appropriate software, the images can be...

Turntable for 3D scanner. What will be needed: 4x screws M6x 20mm 4x screw M3x 15mm 1x 220V clutch 1x cable with 220V socket ...

ATLAS 3D is a turntable 3D laser scanner based on the Raspberry Pi. It runs the open source FreeLSS http://www.freelss.org laser scanning software available on Github https://github.com/hairu/freelss/. ATLAS 3D is a successful Kickstarter that is...

scanner 3d con telefono

First prototype of 3D scanner

A 3D Scanner model with distance sensor

3d scanner based on intel realsense d435 camera

After finding the source code to a 3D scanner turntable on the internet I decided to make my own design of a 3D scanner setup. All credits for the source code goes to Whitney Potter for making the code. Source Code can be found here ...

3D Scanner Concept. ...add me: twitter: @martinhajsinger linkedin: @martinhajsinger https://hajsingermartin.wixsite.com/home