turtle stl file 3d models

*Edit: Added BMG extruder for Dragon hotend step file. *Edit2: Added stls for Dragon extruder. Extruder has 2/4mm tube inserts (bowden tube) for easier glide. Can be converted to 2mm hole without tube in step file. *Edit3: Added Matrix...

I have uploaded a step file of the mounting plate for ease of adaption to other hot end designs. The conversion will easily allow for the stock 220 x220 build volume and allows for the full 235 x235 dependent on duct design (My Manta design looses...

– 37g – 12.39mTotal Estimated Print Time: - 32:22 Hrs.Estimated Material Usage: - 377 grams – 127.09 meters**Please reference the included Assembly Instructions.pdf file for assembly information.Additional Notes:: Recommend printing a minimum of 3...

Rails can be up to 10mm diameter - if using only top rail, then use “spacer” connectors PARTS NAMING CONVENTION: There is a lot of files in this download, so here is a little guide to how to find relevant pieces: rack_main_… - basic 9-slices, “Middle...

3/16" thick x 2.5" diameter o-rings are used for the tires.I've also included files for a passive caster for creating a minimal robot base. Note that at least two swerve drive modules are required to build a robot, but you can use 3, 4 (or even more)...

&nbsp;Support these files as well!How can I support this?Tips are always appreciated, as is support on Printables. &nbsp;I'm also (barely) on <a href="https://www.patreon.com/posts/initial-release-67659789"><strong>Patreon</strong></a><strong>,...

The stock Mini rod span is short enough I don't expect this will result in a noticeable improvement in quality, but you should be able to push your mini to 133mm / sec speeds in Y, with a similar increase once the X axis files are released. This may...

This should be fine since most people who can afford a BlackBelt probably aren't making this ;) Also worth mentioning is that the included Cura file is a zip file. Thingiverse won't allow this as an upload type so I've simply added the .thing...

------------------------------------------------------- The case plug file is for the existing power-in receptacle that comes installed in your printer. I did not include a mounting solution for the on/off switch because this setup is intended to be...

A JPG file containing the decals is included in the pictures section. 8 - Small note: the back_wheel_attachment/left/right might have a few small artifacts in the hidden bottom part. Brush or dislodge them out to avoid interference with the wheel...

These include Core Type B and Core Type C, Type A Valve Backstop, and Launch Pin (the narrow parts sometimes lift off the bed)Changelog2022-04-26: Uploaded Base 21.4mm v1.21 (updated model file reference to Printables); Changed names of Core TypeD...

This is a completely new version of my original design (here: https://www.printables.com/model/145632-dslr-rig) without the cage and with fewer parts.&nbsp;Redesigned in SOLIDWORKS for higher precision.You will also need:15 mm aluminum or carbon rods...

PRINTING INSTRUCTIONS: I would recommend printing the model file titled "marsbase5a" This model file has a base attached to it for easier print removal. I would recommend printing with supports if you don't mind spending time to remove them. If you...

File in case you cannot download from Thingiverse https://drive.google.com/file/d/1WLp7AtCZGsLDsoyeKDpfMY75koo1_Cu2/view?usp=sharing NOTE: controller is factory set for Cooling, it needs setting to Heat also remember you have to press both buttons...

This design is a Remix, the original file is in the following link: https://www.thingiverse.com/thing:4243158 Social networking: -Makers Popayan Group: https://www.facebook.com/MakersPopayan/ -Eureka! -4.0 technology: ...

A JPG file containing the decals is included in the pictures section. 8 - Small note: the back_wheel_attachment/left/right might have a few small artifacts in the hidden bottom part. Brush or dislodge them out to avoid interference with the wheel...

There is also 3mf file if you own a different printer and need to adapt, so inspect the file and be careful regarding the details, otherwise there is a good chance the part fails to print or will break soon. Be also careful that the seam doesn't end...

If there are any errors or you have requests for special changes to design, please let me know in the comments.&nbsp;All pieces are support free!Let's start with the list of parts you will need to complete the project:3D printed parts (See...

 **Additional part sources** --- * [The Tensioner knob is a remix of donnyb99's CR-10 tensioner](https://www.thingiverse.com/thing:2168903/files) * [The tensioner itself was inspired by mukha521's AM8 tensioner but...

Although they should last about 1/3 of the time the official Ring batteries last.I have included STEP files if you want to modify anything. Remixes are encouraged, as I'm sure others could do better.</p><p>People often like to show support to...

&nbsp;well then the “Base full” is the print for youIf you want to make it two colors there is also an upper and lower part available in the files.&nbsp;&nbsp;Is the “Guidance_Clamp” clip on part on the Deck mandatory?! &nbsp;NO it also functions...

Very few supports are needed to print these as well.I also have made the Fusion 360 design file available. The model is partially parametrized, so you should have a decent time modifying it if you wish.</p><p>&nbsp;</p><h3>Parts</h3><p>You will need...

Some Details Note that the .3mf file (and the included .gcode) for the shade includes two PrusaSlicer filament changes to have contrasting colors for the included "beauty rings" on the top and bottom of the shade. If you don't want this, just remove...

The only files you need to print is the Main body and Turntable, everything else is included for ether reference so you can design your own using these style lamps or to check scaling in case you are unsure how accurate your printer is. I have...

I am using a kinematic leveling system using magnets (for size reference of these please check the step file, I ordered them from www.supermagnete.de and the magnetic balls will be sth. like Haydns Magballs)</p> <p>The heatbed is a custom milled...

I only use it to check my current impressions, the LEDs are not on for several hours.I created a notch on the files in order to lower the cable to the right or to the left towards the power supply. ...I added a switch at the bottom of the right arm...

from white to dark grey on a white wall.However, cheap PLA can be used for the wall bracket (bracket) without any problems, as the only thing that matters here is the look and there is no mechanical printing.This is what the files "Brackets 1-3" are...

The other issue is that there are two Y-Values for the X-Values where the asymptotes should be, but this is another thing I had to compromise due to space issues.) Print instructionsPDF Version of Instructions Images...

It will self lock. Put the M3 nuts in the motor mount base and screw the motor mount to the stepper (M3x10). Pick up the M5x40 screw and insert in this order: For the 625 bearings (option 1) * Big gear * M5 washer * 625 bearing * 625 spacer A * MK8...

your FGC-6H should work with the parts provided in this starter kit.movie link:roller bearing hammerhttps://youtu.be/jsGwoxNXUaYupper sand toolhttps://youtu.be/-QtMWLSduyYFGC-6H:  how it works and comparing the heavy bolt vs normal...