usb c breakout board 3d models

by Zenmaster_Maker http://www.thingiverse.com/thing:3345859 Banthas (Star Wars Legion scale) by McAnultyMiniatures https://www.thingiverse.com/thing:3958418 Re-sculpted Star Wars Dewback by DaylightInventor https://www.thingiverse.com/thing:2856774...

__Materials Used:__ - Rope (6mm thick 7m long) loop made with the fastener closed with 4 M3 bolts and nuts - Two broomsticks (23mm thick 1.5m long) connected with a non-bendy tube and a nail into each one - Mounted to the fence with (5mm thick 25mm...

The foam cutter mount I remixed this from only worked with the old MPCNC.It is basically a combination of the mount for the DW660 spindle (https://www.thingiverse.com/thing:944952) and this foam cutter attachment...

A secondary air flow will move from the vents across the board to the exhaust (partially driven by the suction the primary airflow path creates). The upper front vent hole also helps. Just as an aside, the Maestro works fine with the fans I used. I...

The uploaded image is just an example, please check your own equipment & documentation carefully before connecting the End Stop to the pins on your board and make sure all three connections to the optical end stop are correct prior to power up.. I...

Home Depot has 3/4” MDF square boards that are exactly 24” on a side for about $5. Sitting on a base allows the outside hinges to open the doors more freely. If you use the base, you may need to secure it since it doesn’t have much horizontal support...

The LED strips only consume 3.5W (single) and 7W (dual), so it won't put much excess load on the power supply. MK3 power supply connection (24V LED strips only) MK2 Power ConnectionThe MK2 boards don't have as good of place to tie into 12V,...

Maybe V6 heatblock with 40-50W heater or Volcano is a good idea. Electric You have to weld at least one angle connector xh2.54 to the printerhead board. Then crimp fan cables with xh2.54 male-connectors "2 fans in one connector". Like that set of...

by Zenmaster_Maker http://www.thingiverse.com/thing:3345859 Banthas (Star Wars Legion scale) by McAnultyMiniatures https://www.thingiverse.com/thing:3958418 Re-sculpted Star Wars Dewback by DaylightInventor https://www.thingiverse.com/thing:2856774...

I wanted a ship to hold containers for a sci-fi re-theme of the board game "Container" (https://boardgamegeek.com/boardgame/229892/container-10th-anniversary-jumbo-edition)DiceCaller had created a couple models using a neat hex/triangle cargo...

I either only found cases to hold the mosfet(s) or the mainboard; many also had space added for other circuit boards that weren't of interest to me. At a later date, I also modified it for a different type of mosfet and made it more flexible in its...

Support us, donate BTC to 1BUBCeiryEUCgRGsgFkUW6EYMSbdiSGcZF Share your sales profits if it is made into a product Software files Compile and Upload using Arduino 1.8.8 solaroptimal.zip > solaroptimal.ino, parameter.h, display.h library.zip >...

 You only need the left or right versions (plus the others) so the whole thing should print in about 2H 54m or so.The 3mf files are ready to print with appropriate supports and brim.There files, suitably named, for right and left handed...

In addition, there is sufficient space for cable connections from both sides of the board. The node-box is available in 3 versions: without antenna hole, with hole for antenna low (for nodes without battery holder) and with hole for antenna...

... a wall supply or a computer if you are watching the serial port Power Supply, 8-35V X 2 One for each stepper motor. It's technically possible to do this with one supply but life is easier if they are split. Miscellaneous wires Bread board

The clips can be snapped at different heights to accommodate different thicknesses of glass and backer board. 6. There are three ways to mount your picture. As with the edge clips, use needle-nose pliers to insert. Refer to the pictures to see...

But the ‘Darkstar’ didn’t even get off the drawing board. Some reports claim it was merely an experimental academic exercise to gather research for future aviation projects. Others said the advent of the Intercontinental Ballistic Missile (ICBM)...

I can also expand it further with additional panels.I used the following parts:*3/4 x 36" square dowel rods (5 pack)Amazon Item "B01C6BZ2YE" https://www.amazon.com/Woodpeckers-Square-Dowel-Rods-Pack/dp/B01C6BZ2YE/ *Go Create 3/8" Round Wooden Dowels,...

I had a few lids split horizontally when i tried to make those holes manually. A module based 18650 battery pack Print the connector to join multiple x40 packs together, as many as you want! Print the attachment board to mount stuff on the side of...

I wanted a bunch of spare hobby knife handles to distribute through the various places in my shop, but none of the printable versions I found were very robust and tended to let the blade slip pretty badly under normal use (for me that is cutting...

(Deutsche Beschreibung unten) This is a case for the Calliope mini one-board-computer planned to be used in German primary schools. ( <a href="http://calliope.cc/en">http://calliope.cc/en</a> )</p> <p>I wanted a case that can stay on the Calliope...

It moved the height sensor far enough away (laterally) from the extruder nozzle that the dc42 supplied 3-pin power and signal connector collided with my printer's RH Z-shaft; a DC42 Mini height sensor board support for e3d v6 - by simon0362 may have...

An electronics project for printing people should be without the necessity to make a printed circuit board. Not everyone has that capability. Only very simple and basic soldering is required. In spite of that, the project has a certain level of...

I chose parallel, which will put a higher amp draw on the board. I didn't check specs, so do this at your own risk, but it's running fine so far! No support necessary for anything. I printed in carbon fiber infused polycarbonate, but PETG should...

They don't have much to hold onto, and the pots really aren't very strong, so it's probably best to print one and use it to make adjustments, but otherwise leave it off to prevent them from being bumped and possibly messing up the stall board....

100UF...

An emery board is pretty good for removing any rough spots. How I Designed This This was designed in OpenScad. Its revision 8 of this design. ...The .scad files are included so you can customize it.</p> <p>Thanks to Dan Kirshner for the threads.scad...

Still somewhat new to this 3d printing thing, but I figured I'd tackle one of the organization nightmares of one of my favourite board games, Eclipse. Specifically, my first project was to come up with a tray for the game's ship parts. Between the...

... sleeves probably will not fit in the trays. 2) There is a 3-4mm Box Lift: Depending on how you organize the boards. There might be better ways than what is shown in the images. If you find a better orientation leave a comment. ... Thanks,

--------------------------------------------------------------------------------- Print Settings: • Ensure the model is orientated as shown in the slicer image • Skirt - Yes • Skirt Line Count - 2 • Skirt Distance - 1 mm • Support - Yes • Support...