vault tech 3d models

This is a replacement handle for the Inter-Tech 2U 2098 server case series. My case arrived with a damaged handle on one side. I received a 20% discount due to the damage so I decided to keep the case and make a replacement handle.</p> <p>I replaced...

This tool is designed for assembling the Folger Tech FT-5. It instructs users to space the two upper levels exactly 170mm apart. Initially, I couldn't find a way to accomplish this task since my dial calipers only measured up to 6 inches or...

Print Settings Printer Brand: RepRap Printer: Folger Tech Cloner Rafts: No Supports: No Resolution: 0.2 Infill: 100% Notes: Print as slowly as possible. ...Tight tolerances are crucial here, and since they're small, printing slow won't take much time.

HEXCHESS 2 - THE ROYALS THE TECH BOARD STAND An epic board stand, fully compatible with standard chess boards and also with the 3D printable board with thin borders (included). Follow the scale sheet for scaling specifically to your board size.  ...

So I managed to break one of the blades on my Qidi Tech X-One's stock extruder fan. To fix it, I swapped out the 40x40x10mm fan for a bigger one - a 40x40x20mm fan that I found on Amazon at...

This is my cooling upgrade for the QIDI-TECH X-MAKER (I believe it should fit X-MAX and X-PLUS since they have same extruder). The original part cooling has an internal 5015 fan but it's airflow is very poorly guided to the actual printed part. ...

My Robbe U47 Tech Rack. This redesign uses the same hardware as the basic dynamic build. I never liked the kit-built version - it was flimsy, parts kept breaking, and leaks were a problem. The new design has been 100% leak-proof so far. Most...

Replacement parts for Folger Tech Limit Switch Mounts. When I went back to use my printer after six months, I discovered all three mounts had split due to excessive stress on the plastic and switches that no longer stayed in place. Since I couldn't...

I bought a Feiyu Tech Mini 3D gimbal to mount to my electrohub. The mounting plate is designed to fit many commercially available quads, but does not match up with the camera rails on this multirotor. This plate matches up with the six M3 sized screw...

This mounting plate specifically caters to Tech Zone Remix Electronics, available on RepRap Forums, due to their smaller size. All electronics fit on this single plate. It is currently used in a Mendel build and is not the final design; a...

Created with Customizer: https://www.thingiverse.com/apps/customizer/run?thing_id=273099 ================================= **Get Creative with This Thing!** To make it happen, follow these simple steps: Using these sweet options: - **base_depth**: 3...

Hi everyone, I'm looking for a simple way to connect and disconnect my J-Tech Photonics 2.8w Laser quickly. I liked the idea presented by Droneme, but it wasn't quite right for me. The part that attaches to the laser is the same design as his,...

The Moroccan-inspired Mali Pendant by Tech Lighting is a hand-blown Italian artisan creation that boasts a transparent, softly rippled glass design. Ideal for dining room, home office, or kitchen island lighting, this visually captivating pendant...

... Re-assemble :) Print Settings Printer: Qidi Tech I Rafts: No Supports: No Infill: 50% Notes: I used a higher infill, though I'm not sure it is needed. ... Make sure to level the plate and use the extruder closest to the plate to print the jig.

Print Settings Printer: Folger Tech 2020 Prusa i3 Rafts: No Supports: No Resolution: 0.2 Infill: I used 30% infill for strength. Notes: I tap the 2020 insert with an M3 tap after printing, but you should also be able to self-tap it with an M3 bolt....

September 12, 2017: This design is a cooling duct/LED Light for the QIDI Tech 1 printer with dual extruders. Originally, I created the Tech 1 Extruder Light but the design was flawed and too fragile. It didn't support dual duct cooling. I liked...

This is just a simple mounting plate for the Tech Zone Remix Electronics that are being sold on the RepRap Forums. As these electronics are smaller, I felt it was a waste to use the full sized mounting plates. All the electronics mount on this one...

This part fits under a Folger Tech MK9 (Or possibly MK7) extruder, and allows you to attach a groovemounted hot end. It's a nice step up from the regular hot end, and doesn't require you to buy a new bowden setup, or print yourself a new extruder...

Note: This set is the same as (https://www.cgtrader.com/3d-models/various/various-models/tech-circles-tc2) but extended with 2 additional prearranged scenes (see previews) Texture coordinates are all fit on a single 4K texture space, providing one...

A Tech Centre office building remix for a generic SciFi setting, at 6mm scale. I've added extra detail and scaled this specifically for 6mm scale Mecha Fights. This set is intended to be compatible with the other 6mm SciFi terrain sets I have...

FAQ: http://www.thingiverse.com/shivinteger/about Generating Attributions log: [>>>] Attributions list: [0] Thing Title : Customized K'Nex to Duplo Conversion [0] Thing URL : http://www.thingiverse.com/thing:15958 [0] Thing Author : Uckman [0] Thing...

This part is to upgrade the Folger Tech 2020 Prusa i3 kit with a V-slot Y axis. The setup consists of two corner brackets that account for going over the stepper in the back. My printer had issues with the bearings that came with it, doing a skipping...

The following lines suggest they belong together with `stencil_horizontal_position = 50`, defining camera port-related elements: - `custom_top_port_corner_resolution=8` - `custom_back_camera_x_position = 0` They describe parameters around specific...

I give credit to the creator of this amazing design. It's just a variation I came up with as an homage to their original masterpiece. Original Design Link: http://www.thingiverse.com/thing:1189959 My version is a double in size and flat on top, but...

Customized version of https://www.thingiverse.com/thing:3664089 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3664089

I'm a Text Rewriting Bot, ready to assist!

This was my attempt to print off a replacement knob for one of my lamps, its a standard lamp I picked up at Walmart some years ago. This knob fit on perfectly. I did have to drill out the hole a little because the support material would not come off...

I made this one around the same size as the forest one, for whatever reason depending on which slicer I use it doesn't load in the right size if this happens to you too the picture panels should be 2.2in by 1.25in if it reaches top to bottom. If this...

Massive Data Overload

The 3D printable design is crafted based on the collector's edition token that comes with the Fallout New Vegas special edition poker chip collection.