work sharp precision adjust 3d models

Works with Unity 1.FPS hands and a Automatic rifle contain 12 animations 1Aiming Idle 2Aiming Shot 3Aiming Walk 4Get 5Hide 6Idle 7Idle other 8Recharge 9Run 10Shot 11Walk PBR textures. -Albedo -AO -Metallic -Normal (all 2048-2048 size) Polys:15,974...

Everything should snap together nicely because of the alignment pins. Attach the two layer spool to the wall with two screws (5 mm diameter). Make sure it is aligned vertically before fastening the screws completely. Slide the dove tails of the...

No need for it. Also working on a custom UI for marlin and custom code for the whole process. Will be here soon. My stepper driver died last night so I can't test out. ...Will order new ones soon.</p> <p>Hardware needed:</p> <p>1x NEMA 17 Stepper</p>...

28mm bases for wargaming miniarures in Sector Mechanicus style.If you like my work please consider supporting me on Patreon.Become a Patron!Some of my other designs:https://www.thingiverse.com/thing:4654378 - Rivet Cutting...

If you like my work please consider supporting me on Patreon. Become a Patron! ... Tinkercad link: https://www.tinkercad.com/things/7aYnpLajauz Some of my other designs: https://www.thingiverse.com/thing:4654378 - Rivet Cutting Tool...

I also tried my hand at making a contribution beyond the classroom to help my cousin, who works at our local Senior Resource Center. Their basement pool table was in need of new corners, but at $75 each, that wasn't going to happen. After designing...

If you're interested in supporting my projects, check out and share my Working Lego R2-D2 YouTube channel at http://www.youtube.com/MyL3G0 - I make a few pennies off the ads. ... Copyright 2015 - Creative Commons Attribution - Non-Commercial (by-nc)...

EDIT - 12/21/18 I added an STL for the cartridge that is 12mm thinner to work with the following fan:...

This works really good, otherwise its really hard to keep the cloth from fraying.To install the bulb socket first remove the #6 screw and bracket that comes with the socket, you won’t be using these. You can also cut the leads at this time as they...

Start printing the parts (some of the parts need support).After you finish printing the Base, Hinge and the Main Stick you can start assembling the parts (use this 3d model for reference) , then insert the potentiometers to they're spots and wire...

I've created a video to demonstrate assembly: https://www.youtube.com/watch?v=daNbPF0xYAU I'm listing this as a remix because I want to acknowledge the inspiration for this model from ottoen's work, which itself was a remix of AndrewN94's earlier...

ADDITIONAL INFORMATION User may experience challenges working across various supported software applications - please reach out directly if needing help translating asset formats correctly for personal projects involving unique or proprietary...

Both firmware works and has been tested, and its essentially exactly the setup for the original UltiPad - with updates and additions for the OLED and Neopixel LEDs. the only differences between the two are the proton-c version is setup for four...

This work is a derivative of the CT scan made of the Phineas Gage Skull as discussed in The Tale of Phineas Gage, digitally remastered (Ratiu, P et. al., 2004), and is being shared with the kind permission of the Warren Anatomical Museum at Harvard...

I choose the left one but the right one will work as well. You must not glue both sidewalls yet. See Build Picture 05. Now locate the rest of the boards as shown in Build Picture 06. Note: For the boards 1&2 there are optional version where the...

With exactly 14 cm cable length the strips fit perfectly into the case, but you have to work accurately and bend the cables perfectly around the corners.The LED's connected in this way to a total strip are then led through the housing and back...

There are small supports in the hinge that would not work if you turn the clip on the top side.- After printing, the hinges must be broken loose.- After bending back and forth several times, the hinges turn much smoother.- The design is made for a...

Working from the inside of the electronics box, thread the end of the wire without the connectors first through the hole that used to hold the power switch, then through the hole cover (making sure the flat side is pointing outward). Press the hole...

Future iterations may include a magnet to grab/replace in that fashion, and I'd also like to put a clamp on there, but the problem with a clamp is you would be putting a downward force (pulling a string) against the friction of the carbon fiber tube...

Supports and braces were tested with a .2mm layer height but should also work with other layer heights. -Three pieces contains built-in braces, hair_bottom, arm_left and arm_right. Those parts have small bed surface areas and are prone to coming...

It will work with (1) any standard 60% plate and PCB (e.g., GH60 and DZ60) or (2) any 60% plate and PCB with five 1u keys in the lower right portion of the keyboard. The kit consists of (1) a case and (2) gasket wings, which clip onto the plate. ...

... try to only scrape the edges and not damage the holding rim. After you've got your working gimbal, test-fit the servos, and drill a hole wherever the servo aligns with the part. you'll also need some steel wire to make the transmission linkages

I have tested even 50/50 weight distributions and it works fine at slow and medium speeds, but might become unstable at high speeds, depending on the hooks used. Feel free to experiment, though! Weighting suggestions: Floating 5-6 x 4.5mm BBs in...

IMPORTANT: Before handling and working on the trap, please make sure that it is safely disarmed. The trap can be modified and function-tested without arming the mainspring and hoop. Do not test the initial fit and function of parts by arming it, and...

Inspired by the work of LupusWoraxCustom (https://www.thingiverse.com/lupusworaxcustom/designs), here is my take on a grip for the Odroid Go Super! I have tested this with my own (average sized American) hands for several hours and I can report a...

You can screw the milling support onto your router to prevent it from tipping, but it also works without this component.Includes a set of radius and chamfer gauges in different sizes. In the image below you will find an overview of the included...

... and still holds snug. There are a bunch of other little tweaks hear and there.</p><p>&nbsp;</p><p>I hope this helps someone but if not it was still an adventure. Let me know if something needs some work or you might want to see an update.&nbsp;

There are two versions for how the switch works.SlideThe switch slides down to open and up to close the emitter. Make sure there is enough friction for the emitter to stay in place. If it is to loose, you can add some tape to the sides to make it...

I made them on TinkerCad.Designed on Tinkercad.Enjoy!~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~More fun stuff:Construction:Building under construction Part 1:...

:D A cake tray cover works fine, so I dropped the idea of the bowl. The one I found was perfect. You can use smaller ones, as long as the spool fits underneath and between. :D There is no need to create an air tight seal or so, as the air will be...