zonestar p802m firmware 3d models

Fix for mixer issues in the 2.3 Beta Firmware for the GeeeTech A20T HW4.1B This firmware has BLTouch enabled. I was compelled to fix some very annoying issues preventing full control of all three mixing steppers from the LCD. Looks like someone...

Overall, this guide provides a detailed installation process for firmware on a printer, including flashing and resetting to factory defaults. ...It also includes additional information specific to the 2.0 release, such as changes to esteps, BANG_MAX,...

Transferring fastening display for Prusa-i3 from Zonestar. Stud spacing is set to 22cm. ...Display relocation due to button presses causing the acrylic enclosure's deformation.

Basic support for the Zonestar D810 is retained, keeping original dimensions intact. ...The leveling bed sensor adapter has been removed to avoid ongoing issues.

Fan Duct System Designed Specifically for ZONESTAR Series of 3D Printers, Including the P802Q, P802N, and Models Z5, Z8, Z9, and Z10.

The original mount block for the Zonestar P802QS was remastered, minus the extended head length, to circumvent the issue of the bed thumbscrew colliding with the supporting strut.

This is fix for endstop switch Zonestar Z9M3/Z9M2 Otherwise switch can go under the metal and make much noice witch stepper motors

Upper Housing with Load Bearing for the Zonestar P802QA The Bearing Utilized: 688-2RS, 2x16x5mm in Size SLA Tolerance Inside is at 0.1

I replaced the X-Axis Limit Switch on my Zonestar Z5 because it had shattered into pieces after I over-tightened the screw.

Belt Holder and Tensioner Upgrade for Zonestar D810, Version 0.1 - Prototype Stage, May Incorporate Errors. ...Includes High-Resolution and Low-Resolution Model Variations.

Designed a frame mount and bed mount for the ZoneStar P802N, use the chain links from https://www.thingiverse.com/thing:1915486

Due to using steps instead of millimeters, the firmware rounds values down with Floor(), potentially leading to strange results, like the Superman logo. It comprises a 9g servo, two stepper motors, a LeafLabs Maple r5 board, and EasyDrivers. ...I have...

UPDATE: Current Projects - CR10 with double motors (testing in progress): y motor heat issues - Ender3 (testing with a friend): motor heat issues still unresolved, searching for calibration solutions - Ender2: firmware compiled but not tested yet;...

Here is the Link http://bit.ly/2IvE0Zd It includes all the files you need, the stock original CR-10S firmware to roll back if needed, but you lose the power out resume feature. Read the README file - it will really help you. !!!! Changing the...

I also upload the firmware binary file (firmware.hex - ITALIAN LANGUAGE!) as well as the _Bootscreen.h file in which, to make the difference with the original firmware more visible, I made the same initial logo but in negative. CONFIGURATION...

I assume no responsibility for you uploading this firmware; I haven't developed the project or firmware, just adjusted some settings to modify my TEVO.\nAgain, I've used these EXACT files for hundreds of hours, but your printer might be built...

UPDATES: - CR10 with double motor (currently testing myself): Y-motor heat issues - Ender3 (testing with a friend): Motor heat issues still searching how to calibrate them - Ender2: Still not tested, just firmware compiled; need another board...

#Clamp for firmware controllers, a 6-pin solution Links to materials: • Pogo Pins - http://ali.pub/41pr3b • Spring Contacts - http://ali.pub/41m8l8 • Nuts m2 - http://ali.pub/41mat5 • Bolts m2-8mm - http://ali.pub/41mdqc • Bolts m3-10mm -...

... SD card, insert SD card into printer Start printer & wait for the printer to update... (Attached is the calibration cube with the PID BED problem, the second printout after improvement) Back to original firmware from ORTUR normal procedure. ...

After seeing several requests for a Voxelab Aquila BLTouch mount with the defaults in Alex's firmware (https://github.com/alexqzd/Marlin, -40mm X and -9mm Y) I created one for others to use if they like. aquilabltouchv2 - Uses 2 M3 x 8mm bolts for...

I swapped out the old hotend on my trusty ZoneSTAR Z6 3D printer and upgraded to a CR-10 hotend, giving me the freedom to design and print whatever I want without restriction. ...This post focuses specifically on crafting a CR-10 holder with a fun duct...

Plate for mounting E3D Clone on Zonestar Z9, using the original mounting points. Mount the plate with three 4mm screws (12mm long) and a washer and nut on the backside. The Clamp requires two 2 4mm (20mm long) screws. Print in ABS plastic. ... As...

The Zonestar I3 printer performed well with a 7mm frame height setting. Four toppers were printed, one for placement before and behind the arms. STL and SKP files are available for download. ...To install a filament roll on top of the Prusa-style...

... screw holes in the main chassis. The Left guide includes 3 hoops for attaching cable ties to aid cable management above the motherboard. Collection of all my upgrades for the Zonestar at the following link: https://www.thingiverse.com/thing:2936870

... model and made some adjustments to get it perfectly aligned with the ZoneStar. I added a fuse holder inside the casing as shown in the second picture. Print Settings Printer Brand: RepRap Printer: ZoneStar Supports: No Resolution: 0.3 Infill: 15%

... out. ...The tensioner v3 has been reinforced throughout. I'm using a Zonestar P802n X Idler with belt tensioner - it fits snugly and doesn't add any extra space. Print Settings Printer: Zonestar Rafts: No Supports: Yes Resolution: 0.2 Infill: 100%

With the exception of running bed leveling initially, this custom firmware is a straightforward drop-in replacement. Simply flash and dash! To guarantee that proper default EEPROM values are loaded immediately after flashing, I recommend executing...

I found a new GRBL control board that includes manual jog buttons, a LCD and SD support here The Marlin firmware's main.cpp has been modified to include the M3/M5 commands on the FAN port. It works and behaves in the same manner as sending a...

I opted for Stepstick drivers with 1/16 microstepping, customizing the Polargraph firmware to work with step/direction drivers. My printed files are available at http://www.thingiverse.com/thing:16692. The instructions have been updated on github...

Hi,\nI've just received from Sunhokey their latest version of the MARLIN firmware for the Sunhokey's PRUSA I3.\nI uploaded it in my new MKS Gen-2Z V1.2 motherboard, and everything went smoothly. I even adapted the configuration to accept a 12864...