3d printed case feeder for hornady lock n load

Converts Hornady Lock-N-Load case feeder to use 1/2" Pex tubing for the drop tube. This modification improves reliability with .40 caliber casings. Multiple files included. ...The original file was set for pex outer diameter of 0.63" and was a little...

Hello, Here are the files for the Hornady Lock n load AP Auto Progressive Press Case Feeder V2 In this version, the dove tails are removed and replaced by lap/dado type joints. Assembly now requires common #4x1/2 and 3/4 sheet metal screws and...

I use a bit stiffer spring in the turntable part, and tighten it far enough that rotation is just still barely possible so it doesn't flop around. ---------------------- This is a 3D printable case feeder for the Hornady Lock n load...

The upper body was altered to lay flat for better printing. Note: - The upper slide uses a 624 bearing.... - The support rod used was .250" dia aluminum from Home Depot. - The springs used came from an assortment purchased at Home Depot. -...

Prevents upward and twisting movement of the Hornady Lock-N-Load Case Feeder "Pivot Body". If your cases are not dropping reliably in front of the case shuttle or are dropping on top of it, this part will help prevent the pivot body from moving out...

This is a breakaway replacement piece for hornady lock n load progressive reloading press. ... Print Settings Printer Brand: Prusa Printer: Prusa Clone Rafts: No Supports: No Resolution: .2 or better Infill: 100% How I Designed This built in Microsoft...

Remix part for Bartje64's printable case feeder V2 https://www.thingiverse.com/thing:3844226 The tubes I ordered from e-bay were 5/8" OD, 1/2" ID plexiglass. They were just a bit too wide to fit in the tube holder on the original, so I took it into...

I designed a center light for my Hornady LnL Press, Light is from eBay (eBay item number:203018246644). ... I printed with supports so the hex end would come out need.

This is a printable replacement powder baffle for the inside of a Hornady Lock-N-Load powder measure.

The case wheel is a friction fit on the motor coupling incase if jamming. ... YouTube video - https://youtu.be/UFJEm6fwK6M Parts used, Motor - https://www.amazon.com/gp/product/B07FD98N8J/ref=ppx_yo_dt_b_asin_title_o05_s00?ie=UTF8&psc=1 Motor...

Hornady trio zahnrad

This is a replacement for a Hornady Lock-N-Load primer tube support (Part number 398318). It has 4 feet instead of 3 and goes 1mm deeper into the primer tub housing than the stock part. ...Made it to help a friend who had broken his and didn't want to...

Prior to this the guide rod kept hitting the collater that sits atop my 3d printed case feeder just after I filled the primers. If I didn't fill up the primary the follower would sit low enough that it wouldn't hit but that left me reloading it too...

Stand with storage for Hornady Lock-N-Load powder measure. ...

Hornady Lock-N-Load bushing stand

Large one part bin for the Hornady Lock-N-Load auto progressive press. This works great with my setup including the InLineFabrication mount for the press. This may or may-not work with different press mounting setups. This is much larger than the...

This is a simple tool holder for my Hornady Lock-n-Load press. Its small enough to be out of the way and still be convenient. It has spots for four Allen keys and a brush. The four keys are: 5/16 - For the plate 5/32 - For the primer tube 1/8 - For...

This is a mountable primer catcher for the Hornady Lock n Load. Simply mount the primer catcher to the side of a desk and run a flexible tube from the primer discharge chute to the catcher. ...Will hold a few thousand primers before needing to be...

A very nice and neat way to store reloading dies in their Hornady Lock-N-Load bushings, the best QD way to use reloading dies. This holder will hold a total of 5 dies. It also has a slot to stand a powder scoop and a shelf for the shell holders. I...

;-) ____________________ English: This is a holder for two complete Hornady LnL AP Powder Measures (incl. case activated powder drop) to install directly on the bench when they are not in use on the press. The small holes are only to safe filament...

... making adjustments, so they're not rolling around my workbench. ...This stand will hold 4 dies in their lock-n-load bushings, and can even hold the case activated powder measure. ...They simply drop in place and don't lock, so it's easy to remove them.

This is modeled after the Hornady Lock-N-Load® Control Panel Primer Level Sensor. It slips over the primer tube and the clamping shaft collar from McMaster will activate a microswitch when the primers drop to a certain level. The hole at the...

Hornady LNL AP primer feed bracket.

Hornady apparently has a few different versions of the castings for the new presses. This clamps should fit those presses better. ... 7/2/21 Added a version of the bullet tray that should fit presses with roller handles like the Inline Fabrication...

BTW, in some of my pictures you can see the excellent case feeder remix by bartje64 located here: https://www.thingiverse.com/thing:2883143 I have included the openSCAD files so you can edit things if you need to. I only ask that you give credit and...

Fixed base for the bottle with the ejected primers.

Designed this Hornady L-n-L case feeder mount adapter to go in between the 7 collator tubes and Renakx's case feeder mechanism as he had used someone else's adapter which seems to be no longer available for download. Printing: Printed in PETG at 230...

To use the Lock-N-Load Overall Length Gage Hornady caliber-specific Overall Length Gages are required for use (sold separately). ...These Overall Length Gages are made for all common cases from the 17 Remington to the 500 Nitro Express and are oversized...

Print Settings Printer Brand: MakerGear Printer: MakerGear M2 Rafts: No Supports: No Infill: 80% Notes: For the real thing, I highly recommend 5 or 6 layers on the bottom (which is actually the top of the tool), 6 layers on the top (which is actually...

Hello, For my Hornady Lock-N-Load AP reloading press, I designed a bullet feeder for the Caliber .45. You can print all almost all parts without a support structure. I only printed the base body with a support structure on the head. You need 2 M4x16...