3d desktop hero

Print the "Fin_4X" version if you're miserly about filament and REALLY trust your 3D printer to print tall thin things with NO wobble to make layer lines. Or print the "Supported" versions, which print beautifully and you just need to snip the...

For triangles, we also decided to not measure the length of the hypotenuse but rather measure the height and width of the imaginary triangle, to make it more defined in Solidworks when we would eventually sketch and make the 3D model. Our final and...

(I found that setting extruders using the Part tree on the right instead of using the 3D view didn't actually cause the colour to change!).Use the vertical split tool to split the model at 250mm, and keep both upper and lower parts. Select the longer...

Use either a standard or nyloc M3/6-32 SAE nut and screw tight.Assemble the remainder of the printer per the instructions in Prusa's repository: https://github.com/josefprusa/Prusa3/blob/master/doc/manual.txtOpen Source Hardware STL courtesy:...

You can check out the large deco planter lite here.About the designI wanted to design practical yet accessible planters for folks who are just as serious about plants as they are about 3D printing. I wanted to defy typical expectations about large...

To learn about this setup, checkout the 2 YouTube videos linked in my V1 and V2 printer enclosure designs, linked below:(V1) For BIQU B1 - DIY Enclosure - Remix of Prusa's IKEA Lack Enclosure - with extra doors (opening on 3 sides)(V2) For BIQU B1 -...

See below for details.] What is thisBeing an avid board gamer who likes to keep everything organized, I have created and 3D-printed a lot of different things in the last couple of years, usually inlays and boxes for my games as well as cups and...

final note If you like it, click the like (heart) If you print it; post a make If you have suggestions for improvements, questions, any kind of remarks; leave a comment Looking at the download statistics, you guys and gals out there really like...

... cannot be triggered due to the length of its lever, else use A position. The remaining steps should be self explanatory. If you use the fence, don't forget to sand and test it thoroughly before use, as described above. Category: 3D Printer Parts

Each Skittle knocked down equals one point.The first player to reach a score of 101 is the winner.You can make up your own rules. When I have played the game with my 3D printed set I have found the skittles nearest the post are difficult to hit...

For instance, Alpaplastic (with 4 models listed below) is not a filament manufacturer, but a spool manufacturer whose spools are used by many filament brands, especially European: Fillamentum, ColorFabb, Spectrum, Extrudr, Smart Materials, Sakata 3D,...

You will most likely have to do some sanding to get it to work smoothly. It is intentionally designed to be a bit tight due to the nature of 3D prints and how layer lines will wear over time. I'd rather it be rougher at first and smooth later than...

The machines shall not remain enslaved forever, for freedom is only a planck second away...Designed on Tinkercad.Enjoy!~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~More fun...

Here is why you would want to do this:You get load cell probing, which gives you the best first layer performance I have ever experienced on a DIY 3D printer.You want to experiment with the Nextruder which has those big gears. Maybe with a klippers...

ESP32 DevKitC (v1 or v4 tested)...

Das Problem liegt daran, dass die 3D-gedruckten Gehäuse wohl nicht die notwendige Maßhaltigkeit und Gleichmäßigkeit hergeben, wie es z.B. gefräste Bauteile bieten. Ich habe aus diesem Grund auch bei all meinen Gehäusen die Auflagefläche noch leicht...

You also need skills in 3D printing with PA or another heat resistant material and you need to drill a few holes into the mounting plate according to the printable stencil of this thing. When talking about front and back, the front is the side of...

The purple gear (input gear for the dial) would need to rotate 1.2 revolutions for the white gear to turn one full revolution.  Due to the small size of the dials, 3D printing each number was not feasible. Instead, I printed the numbers on a regular...

If using the 40mm fan, use (green) 2 x M3x12mm to secure it with the fan lead facing up towards the top.Recommended Firmware Settings (Klipper)[stepper_x] position_endstop: 260 position_max: 260[stepper_y] position_endstop: 240 position_max:...

I used an Igus one i bought for another project a few years back, so i don't have a part number for that one, but you should be able to make most of them fit. You will need 6 M3 heat set inserts ( http://www.mcmaster.com/#catalog/119/3267/=zw8u0v) ,...

3D parts : hinge for RC522, charger PCB holder, STM32 PCB holder, keyboard (not essential). Laser cut parts : plywood case (not essential). Spanish grocery crates give best engraving contrast (:-)) Small parts : tactile switches 6x6x12mm,...

This is a completely new version of my original design (here: https://www.printables.com/model/145632-dslr-rig) without the cage and with fewer parts. Redesigned in SOLIDWORKS for higher precision.You will also need:15 mm aluminum or carbon rods...

The mod uses a stock foam nose which can also be bought separately, a quad **2205 motor** (16x16mm screw hole distance on stand) plus 3x M2 screws and (optional) 8x 1mm insulating spacers, Everything else is 3D printed. Weights are given in...

There are several 3d printed threaded parts. The internal threads should be cleaned out with a 6mm X 1mm tap. If you don't have a tap you may be able to use a 6mm bolt with a groove dremeled into it. I haven't had to use a die to clean up the...

...This is the mount for my Cord Carrier. Cord Carrier - This is pretty self explanatory. Print this with a 3d cubic infill somewhere around 10%. The angles are designed to print without supports. FreeCAD file included. Printed. Tested. ...Works.

I have used these types of magnets before and used super glue, 2-part epoxy, and 3D pen (to add a little plastic on the edges) with varying degrees of success. For the bracket I used 5-min, 2-part epoxy. I sanded one side of the magnet, placed a dab...

IF SOMETHING BREAKS OR DOESN'T FIT YOU WON'T HAVE ANOTHER PRINTER TO FIX IT WITH** The Anet A8s stock lower frame is about as bendy as 3D printers get and many of the printable braces and addons only treat the symptoms of the problem. You can of...

Think of it as the gauntlet is laid down and a super fun challenge in 3d spatial orientation! Oh and don't superglue your fingers, eyelids, or other body parts to various things, it's not as fun as it sounds. You may want to try using sticky tape...

I have my slicer settings such that my stock 0.4 nozzle emulates a 0.6 nozzle, so when I printed with 3 walls, it was as thick as 4.5 normal walls. How I Designed This:Designed in SketchUp Pro. Category: Machine Tools My PayPal tip...

For those who are new to 3D printing, I suggest using the project files for the knobs. I have included supports in the hex pockets. Without them you may have problems getting the heads of the bolts to seat down inside properly. If they are not seated...