3d print designs

peeing mule on water box with solar charging and LED light Video: https://drive.google.com/file/d/1E4aU50-sGUfZatjUAsKsD0yaGoPQSH_f/view?usp=sharing Print instructionsI used silicone and resin to make it waterproof....

For a complete listing of character maps, do a simple search for "ASCII character map" Print instructionsOnly requirements are an Arduino Pro Micro (I used a clone board from Amazon -- HiLetgo 3pcs Pro Micro Atmega32U4 5V 16MHz) You will also need...

Remove the short piece of filament, reinsert the bowden tube into the coupler and print without the worry of irregular flow. #Other side effects: From time to time your bowden tube in the hotend will perish due to heat and need replacement. ...

Because of the height of the box, the width of non-snug sleeves, and the text size required to come out visible without a .25mm nozzle (and by Thor, I would not want to print all these separators with that!) it became necessary to make the dividers...

This miniature comes with optional presupported files for resin printing. These files come as ready to go STL files or Lychee files if you wish to edit the supports for your custom needs. You can find my latest releases over on my Patreon!   ...

einfach Fragen! Print instructionsUnassociated tags: 7 segment, 7 Segment Uhr, LED clock, LED Uhr, RGB Uhr Category: Household Summary Ich benutzte PLA in schwarz und farblos-transparent Benötigt werden folgende Teile Druckteile: jeweils 4 Stück:...

- The diameters of the holes is optimized to be just right to get 0.5mm holes, tight, using a 0.4mm nozzle and printing at normal cura settings at 190C of temperature. Beware higher temperatures, the walls sag and clog the hole. You should modify...

... Curved step dr. x 6 * Straight step x 12 * Pot x 1 The file of the cards is mounted in six units with two spares in case some are lost - this way, they can be repositioned with matching color. There's also an individual file for printing as needed.

Back slots have max total length -10 layers high when including only last 2 slot values provided per pin count type and front most pins only; total slots are determined at time of print so all pins could easily reach their maximum cut height without...

Also, the "spikes" on the gripper didn't print well and had layer separation. The gripper is the part that connects onto the end core which pulls out. It uses a screw to tighten it. There are 2 gripper versions based on if you have the normal...

Lightweight PLA tool is non-conductive, non marking and wont damage your materials if dropped the same as a heavy chunk of aluminum will.  Files Grouped in 5 Categories:MK3S+ Gcode Pre-Sliced - combined : All Files to build everything pre...

Files to print: ========== - 2x __optical support v3.stl__ - Support for the optical Endstop - 2x __Ender 5 - Endstop trigger v1 15mm.stl__ - Parts to trigger the optical endstop 15mm should be the one you need but I included a shorter one just in...

You don't need to print anything to get it working. Another thing I noticed, If you extrude filament on the button and then press again to stop. The hotend does not switch off on this printer. Kids fire hazard if left on Of course if you went...

Planet's rings are stable thanks to the gravitational influence of the planet, and the presence of shepherd moons, like Prometheus and Pandora, that prevents the accretion of the disk material into a denser moon. Saturn is also known for having...

==================================================================== Easy to print, assemble, mount/unmount. To assemble with Nema14 motor you will need: ----------------------------------- * A set of parts from BMG or clone (gears, bearings,...

I added the printed parts to it. The latches are removable and allow the cover to be released with the beetles. For that I use an M6 rod which crosses all the pieces of the slice. BE CAREFUL to only glue the end caps to the rod once the other parts...

You’ll need a large printer for the Converter to accommodate the handles but it was necessary to print in one for strength (peace of mind when a £500 drone hangs in the balance). The phone clamp requires an 80mm M6 threaded bolt (I buy threaded...

BOM:-Smart filament sensor BTT upgraded version-2x screw M3x10-7x M3 Heat Inserts Nut Heat (same in original )after print carefuly cut the X  UPDATE: config: now add Gcode command for turn ON/OFF by: “SENSOR_ON” or “SENSOR_OFF”config...

In a few million of years Eros could change its orbit to a lower Earth crossing one, becoming a member of the Apollo or Aten group. Depending on how close it became to the Earth, it could be a Potentially Hazardous object (PHO), an object capable of...

The support piece in the D-pad space will punch out with a punch and hammer after printing.Just place the shell on something with free space under the D-pad area and punch the support piece. Wiring the 9-pin d-sub for Amiga, Atari, Kempston or SEGA...

You can probably find some of those part somewhere else for cheaper and in the right quantities for the project) TT motor 1:120 reduction: https://www.amazon.ca/dp/B07DPNQMXS/ref=cm_sw_em_r_mt_dp_U_Mhf4EbDJ1WETF Motor Drive:...

The equipment tray and servo lock **must be printed as one assembly**. I separated them so you easily could make servo lock for different servo (in that case I use 1181MG servo). I made the square on the equipment tray floor for you to easy pairing...

Again, check several times before you drill. Overview of some assembly steps and setup here: https://youtu.be/QQAKxDcRNgc Print Settings Printer Brand: Prusa Printer: I3 MK3SRafts: No Supports: YesResolution: 200 Infill: 15% Filament: Mainly...

A constant current driver operating from 6 V to 15 V should do nicely for powering it directly from the main battery and adding an RC switch to control the light by the transmitter.\r\n\r\nI printed the chassis without supports using PETG and lots of...

No print support needed!This is an as-is project, will not improve it any further.It works great, cooling is better than stock, it's solidly attachedonly downside is limited visibility on the nozzle.This is a bit weird to setup due to the metal plate...

Plus more being added please see table belowSorry Painted in lettering and not double colour printing, Found a very light soft grit sanding made using the fibre tipped acrylic paint pens easier to use. Taken from...

I print it with the cut in the bumper, which you can separate carefully with an exacto. Then wrap the bumper around, and trim the plugs as needed until it fits together well. Then I use my soldering iron (set around 3/medium) to heat up the edges...

The measurement is relative to the height it extends above the surface of the badge.[background color] and [foreground color]These dropdown boxes change the colour of the badge background and the contrast colour which effects the border , logo and...

So _1_6_10_7 is 1:600000000 or one in 60 million. S16 PrometheusPrometheus is a small inner Saturn moon. It orbits near the inward side of the F ring. Its gravitational influence helps to stabilise the ring. This type of moon is called shepherd...

Use the backlash option to allow for the gears to work with printing inaccuracies. Bevel gears are more complicated. Meshing bevel gears have the same cone distance, circular pitch and pressure angle. The cone distance, circular pitch and number of...