3d print fidget toys

Here you will find blueprints for the 220mm carbon frame, blueprints for the electronics protection to be milled out of aluminum, and some printed models. Assembly video - https://www.youtube.com/watch?v=QfWXixFQmGc I used 3mm carbon for the...

Here are the necessary components: Raspberry Pi Zero W (1) Screws (2.2 x 4.5mm) (7) Nano Servo (e.g., Turnigy T541BBD) (1) Videos demonstrating the project in action can be found here: https://www.youtube.com/watch?v=_hPZF4_aZSA...

It consists of a "flying" assembly (2 parts) and a ground assembly (3 parts) which should print all together in less than an hour. You also need two pieces of string (ideally strong, non-elastic and very thin) or wire and a standard-sized tealight....

This is accomplished by printing a column of fanned-out light pipes that radiate from the LED. Continue reading below the videos! Videos: They are all extremely short. Warpcore running at warp factor 2 Warpcore Standard from Novel Mutations on...

http://www.thingiverse.com/apps/customizer/run?thing_id=53235 Instructions Using the following options: pinNumberY = 35 pinNumberX = 13 GEAR GENERATION ON Music Cylinder Teeth Number = 24 Minimum Diameter = 1.5 inches Gap Between Gears = 1 inch...

... I get my Nylon Setup going, I may try this in Nylon as well. But for now, here ya go. :-) Print Settings Printer brand: Creality Printer: Ender 3 Pro Rafts: No Supports: Yes Resolution: .2 Infill: 25 Filament brand: Duramic Filament material: PLA +

I was able to incorporate all the points that I had missed in the past.One of the biggest features is that the component can be printed according to current needs using the customizer within OpenSCAD.Previous solution:The whole thing is based on my...

Assemble the printed parts by snapping the front and back onto the top/sides piece, making sure that the LED goes into its little side hole and the Pi camera cable does not obscure the HDMI opening in the top. 3. Plug the USB DIY connector into the...

Edit 1: Separated the crab from Kraken Guard shoulder 3 to make it a bit easier to print. You'll simply need to attach Clad in the strongest armor the Legion has to offer, Tide Lords act as the shock troops and personal guard of high ranking...

It prints quickly, uses only about 1 gram of filament (0.33 metres of 1.75 mm filament), and is very easy to use.It clips onto the spool of any brand of filament, so it's a universal clip. It can clip onto 1.75 mm filament or 2.85 mm filament, so...

Use a thread lock on the bottom 3 screws to prevent them from vibrating loose and insert them into the remaining 3 bottom holes and tighten until snug Printing I would strongly recommend a filament that is UV stable so that prolonged sun exposure...

It is highly recommended to print this box in PETG due to PLA's tendency to deform over time under compression, compromising the box's structural integrity. To further enhance stability, consider supporting it from below with rubber feet, ensuring a...

... points. This needs supports for building (you might try flipping it upside-down to check if you need less material - this depends on your printer. Also added full- and half-height main body extensions (these can be printed without support).

... for a security camera through a piece of glass. 1. As a way of passing USB and power cables through a metal cabinet. ### NOTE The OpenSCAD script generates models with errors, though the errors are fixed by slicers and don't cause printing issues.

There is also an extra STL file (TSC - Support) to use if needed to help support the outer part of the middle ring when printing. ... Height = 1.4" (below the base) Threads = .4" (above base) OD = 1.37" ID = 1.055" Ring in the middle is .1" thick ...

Clean the magnet holder and the handle bar, once printed, so that the hex bar can slide into the hex holes without being too loose. 2. Snap a round magnet on both sides of the magnet holder, adding more on both sides in a balanced manner. 3. Wrap the...

UPDATE 2019-04-26: added redesigned chain for easier print "Chain Whole V3" and fixed bug, both sides needs equal number of chain parts, old design has one missing chain part. Old design for some people fused too much, couldn't get it separated. New...

I liked the idea, but I wanted to change some things: - plastic rolls instead of metal bearings pushing on the glass - position closer to driven rear gears where the force is needed to keep the gears in contact - easy to replace one drum with another...

Here are the dimensions for the eye module: * Length: 100mm * Width: 45mm * Height: 30mm All the parts were printed using ABS and then treated with an acetone vapor bath to give them a smooth finish. After the vapor bath, I drilled holes in all the...

Thanks dscarbro, that's simple and great!I also print other custom files as they are:Prusa MK3 & MK3S Clip-in Tool Storage Box from Strathpeffer3D   ...

Not only was it my first real model using FreeCAD - which I'm still learning - but it's also my very first attempt at designing printed screw threads. True to form, I didn't start with something simple where you just look up standard threads on a...

I found in using my original printed design that the holes didn't allow for the kind of seasoning dispersal that I prefer (lots of it!), so I increased the hole diameter from 2mm for each hole to 2.75mm. This should allow for more or larger grains to...

Please be so kind as to leave a tip if you decide to print and install this and share your results. Advantages of this design: - Universal - Suitable for hotend and under bed installation - No loss of build volume in any direction - Easy...

For this, you will need a few parts: EzStruder direct drive or bowden doesn't matter Low profile motor support printed part (see my thingiverse thing) 30x30mm Fan shroud v3 (or other thingiverse thing version) 3 fans of 30x30mm (or different size,...

I printed the original design and carved and drilled and glued until I got something that would work for me but it lacked elegance – actually it was downright ugly. The original design looks like it was done in Design Spark Mechanical and that...

Printed in PETG with .2mm layer height. PETG is recommended if you're going to put this in your aquarium. The more infill you use, the less buoyant the rack will be in the water, also depending on the wall thickness you use. The provided Suction...

(You can use a simple arduino sketch that prints to the serial monitor when a button is pressed) - Get a sheet of foam, put a thin line of superglue across the bottom of the case, and place it on the foam sheet. It shouldn't take more than a few...

I was thinking about adding wings to the knurled handle but decided against it for now, maybe for revision 2 and may well remove the knurls to reduce print time. Have fun experimenting! --- January 8, 2021 update: After using this for a...

More suggestions==================== I recommend printing the socket adapter and the snap style arm in ABS for proper flexibility/operation. PLA may be too stiff for them to work well. Also, depending on your setup you may want to use a brim on the...

**************Please add your print in Made directory************** **************Please Like <3************** **************Folow Me !!************** **My Other Upgrade** https://www.thingiverse.com/thing:2720365...