3d print key hook

... a small riser to get my cheap red dot (https://www.amazon.com/dp/B00A36MKUO) to the correct height for a good cheek weld on the taller dust cover. I recommend 30% infill and PETG for printing. ...If you have any issues or remix it, let me know!

Print out little tabs for the aluminum plate. Total of 4 tabs were needed when using the 6″ x 6″ aluminum sheet. 3. Place the tabs on the top of the aluminum plate, then attach a metal circle around the plate's edges to keep everything in place. 4....

So _1_6_10_7 is 1:600000000 or one in 60 million.&nbsp;S4 DioneDione is similar in size with other Saturn's moon Tethys. Like Tethys with <a href="https://www.thingiverse.com/thing:3368027">Mimas</a>, Dione is in orbital resonance with <a...

This inner step, which is the distal 5 mm length of the pin, allows insertion of 1.75 mm printing filament, to lock the pin. The pin itself is split with a .75 mm horizontal slice, so the pin can expand when the filament is inserted. The...

The launcher handle and rack parts should be printed in PLA (it's stiffer than other filaments) and with at least 3 perimeters and at least 20% infill. None of the parts need supports.LaunchingFirst, roll the wing onto the rack of the U-shaped...

Two are required, the shape is rotationally symmetrical so only one model is needed, and printed twice. The jig is 2RU (3-1/2") high which is the same as the smaller PDP-11/03 chassis height. To use, simply push the jig into the rack from the...

Steps: - Print the file - Slide the PTFE into its location at the desired length - Use a felt tip pen to mark the start of the contact on the tube - Take out the tube and cut it round on the outline as on the attached renderings - Replace the tube -...

I doubt it will work on other 8-tooth spools, but it doesn't take long to print and find out. Using it is pretty straightforward, but I'm going to go into detail anyway. Besides, it gives me the opportunity to play with some of "Markdown"'s features...

I haven't found the need for much more than the 20mm max height of the print, though I did make a 40mm version just in case. There are two sizes to the soundhole mount. One has a 3mm top clearance and one has 5mm (for thicker guitars, like...

The stock arms were strengthened (now printed separately). Designed support was removed from the trigger well and mid section. The magwell fit and detent were adjusted. More space was made in the end cap for hose. The bottom front picatinny rail was...

... for reference, obviously these parts are available from numerous sources and you may already posses some of them. ... The case and the lid were printed with a 45% infill from PLA but PETG could also be used. The feet were produced using TPU. ...

Recommended Material for printing: Sainsmart TPU @ 01.mm / 210°C/ 40mm/s / no retraction Update: You can now buy my Gatehunter pod combined with the LeDrone Club Pickle frame from...

********************Please add your print in Made directory***************** ********************Please Like <3***************** ********************Folow Me !!*****************...

material consumption closure pieces are molded at 100% fill for added strength I added the z axis centering device to the et4 base for those who still would not have to use it with a 608 bearing Print settings Rafts: No Supports: No Resolution: 0.2...

What you will need in addition to the printed parts: Six, 6-32 by 1'' Mechanical screws and matching hex nuts. (Close dimensions will also work, the slots have some play to them) One or two small springs, approx 4mm diam. x 20mm. These are optional...

... As an option, the NEMA17 motor strapping allows to fix a motor with two 3mm diameter screws. Note: The instruction mentions that some parts are designed to be printed without material support, and that the device has been modeled with Fusion 360.

New short blades printed in one part, much stronger for the same flight. * Fit in Prusa MK3S (210x200) * New 2 parts screwed cabin. If you don't have screws, you can glue the two parts. Update 22-03-20: New bimotor version The advantages of a...

When printing this jig, the only supports needed are below the two alignment fingers. 1/2" PVC - Metric Drill Bit [1/2" PVC Drill Jig - 12mm Bit - 1" Spacing](https://www.thingiverse.com/thing:5137859) [1/2" PVC Drill Jig - 12mm Bit - 1.5"...

It's essential to print this component in HIPS or a similar material that's more heat-resistant than PLA. I've tested it with PLA, and while it works initially, it deforms and becomes brittle over time. Additionally, the cooling duct was designed for...

Printing is straightforward and there's no need for supports (except for the diffuser), any spans should be OK without them. There's a little slack to allow the diffuser to fit. If your tolerances are a little out, and the face isn't tight in the...

This miniature comes with optional presupported files for resin printing. These files come as ready to go STL files or Lychee files if you wish to edit the supports for your custom needs. You can find my latest releases over on my Patreon!   ...

... Because in nearly every religion, love and forgiveness are good qualities that help society. So happy spring, everyone - wherever you may be. Much love. PS - Print these in the most ridiculously bright colors before you toss them into the fire!

Additionally, I printed 13 [quick change](https://www.thingiverse.com/thing:1996091) pen thingies for my use. Since I utilized ultra fine point sharpies, the lid didn't work as intended. Therefore, I've included the STL for my custom lid in the...

I think I had printed all the versions, so everything should fit. If not, tell me. - For everyday use.<br> - Protects your pens from damage and direct sun.<br> - Diameter 53 mm.<br> - Height depends on type. About 160-170 mm.<br> - You have all...

During printing the holes can sometimes be narrower. Therefore it may be necessary to drill them out.Take one thread and make a multiple knot at one end and then pull the thread through one hole. Place the top ring with the bottom side facing up. Pay...

You’ll need to print the following and its best to fit in this order: If running the V6/Dragon carriage mod then fit the cable retainer and cable into it first, skip this step if you’re not. I’ve included a few options you could use: Cable...

It can be printed without support, although one of the nut traps may require some cleaning up. There is a deliberate single-layer bridge between the nut traps at the bottom and the 3mm holes at the top, which will need to be drilled out to 3mm. To...

(You will want to print a 3m spacer for each of the m3 screws, and a 2.5mm spacer for each m2.5 screws you use for the case. You don't need any spacers for the stand base and attachment Once assembled I set up the Pi to load my weather station...

My plexi has arrived and fits tightly, but it's essential to measure yourself as you build due to print expansion and margins for error in cutting. Measurements are: * Main Panels: 446mm x 524mm * Door Panels: 213mm x 524mm Other objects used in...

I have included two versions of the mount, one is with the rail centered on the overall enclosure and the other is with the rail centered on the top part of the enclosure resulting in a slight (5mm) offset from center. I also went ahead and added in...