3d print kriss vector

- PrusaSlicer recently implemented a change for "Elephant Foot Compensation" that changes how the first layer is printed so that it isn't wider than subsequent layers. - I recommend setting the value for this at .1mm, because I found this change to...

When printing this jig, the only supports needed are below the two alignment fingers. When you import this part into your slicer software, it will likely need to be rotated to lay flay on your build surface. 1/2" PVC - Metric Drill Bit [1/2"...

Human: Gameplay Video - https://youtu.be/oej_kcawIRE Parts: (6) - m5 x 30mm Bolts (6) - m5 Hex Flange Nuts (6.5") - 1/2" PVC SoftTouch Self-Stick Non-Slip Surface Grip Pads - (6 pieces), 1" x 4" Strip - Black...

Summary: My initial build area was around 80mm; a print requiring more height prompted me to design modifications for increased build height. Upon inspecting my printer, I identified areas ripe for improvement. The result is a heightened build area...

I designed and printed this handle to fit the motor connected 3 18650 batteries, push button, mounted all of that and got a nice small low rpm cordless drill. Low rpm drills are needed in many cases for example for drilling wood and plastic. If you...

Please note that if the magnetic tension is too high - for example, if the magnets are too close together - this can soon lead to the printed parts bending. There are two tops to choose from. Here's a video: https://youtu.be/lwLGZ7oSHqY As...

... the sulfur and phosphorous expansion set (http://thingaverse.com/thing:2350618). Print Settings Printer: Da Vinci 1A Rafts: Doesn't Matter Supports: Doesn't Matter Resolution: 0.2 mm Infill: 10% Notes: Three perimeters works well. ...I used ABS.

The play translates into uneven surfaces which are readily apparent on large flat horizontal surfaces, but also affect every other print in some way. There are a few mods here and you can try all or one at a time. First off, the bearing holders on...

I would recommend printing with 100% infill. Included in the download is the sketchup source file for your own customization (Hint: I always include my source files). UPDATE!!! I still need to determine the pinout. I will post it up here once I...

If you prefer the drag-chain to go up and along the y axis than you may want the vertical spacer at the mirror mounting. If you've had this experience, feel free to feed back to the mirror suppliers that their compatibility with K40 is marginal and...

Font Narrow Widen = No widening of narrowed characters, a setting from older designs where letters may need expansion when space runs low so as not fill too many vertical spaces in tightly stacked horizontal text columns across page; it reduces size...

Scan the sheet using a geometrically accurate scanner (for example the ScannerPro app on iPhone making sure geometry correction is enabled.). Follow this youtube guide to import the scanned image into FreeCAD and trace the contour of the lens. Pad...

I printed this with pla on my prusa mini with supports on the build plate only, 40% infill, 4 perimeters. for the support settings i used: Z contact distance: 0.2mm pattern spacing: 3mm contact layers: 4 xy separation between an object and...

When printing the lower air duct, I did not use support inside of the duct itself; instead, I used some outside. Internal walls are designed to eliminate the need for support which would be difficult to remove. The duct on the extruder holder...

Additionally, I printed 13 [quick change](https://www.thingiverse.com/thing:1996091) pen thingies for my use. Since I utilized ultra fine point sharpies, the lid didn't work as intended. Therefore, I've included the STL for my custom lid in the...

It can be printed without support, although one of the nut traps may require some cleaning up. There is a deliberate single-layer bridge between the nut traps at the bottom and the 3mm holes at the top, which will need to be drilled out to 3mm. To...

... below the Pi. I really like how the case turned out and that my RPi 3b+ is now firmly attached to the MK3S. A couple of jumper wires onto the Einsy board and I don't even need a USB serial cable or power supply for the RPi. Print and enjoy. ... Pm

Printer Settings Printer: Migbot i3 Resolution: .2 Infill: 30% Post-Printing Assembly The Z-Axis adjustment block rides up/down on the outside of the front left leg (near the top). Inside the sliding adjustment block, two 8-32 nuts with a small...

Instructions 1) Print equal numbers of receivers, and grabbers. 2) Slide a couple onto each end of a strut 3) Slide shorter struts into these for support, or whatever 4) Rejoice! By default, these pieces fit on 5/16" wood dowels. You can easily...

Not counting shopping and printing time, this project took me about an hour and a half to complete. Thirty minutes of that was just waiting for the silicone caulking to dry completely. Everything I bought came from stores near me, but the components...

Can be printed with a moving head. Arkham Horror investigator - the professor by Craigen https://www.thingiverse.com/thing:4649571 Longboi Trophy by HiyuMarten https://www.thingiverse.com/thing:4706958 Stoat by Davision3d ...

Installation Notes ----------------- • Print out (4) board spacers and install them between the Raspberry Pi board and LCD screen. They are thin enough that you can use the supplied 2mm screws for the LCD screen. • You may want to install the SD...

In the models of this brand has everything you want: bright colors, fine fabrics, playful prints, classic cotton linen. Today in the world open over a thousand stores of this brand. This American brand created to make women courageous enough to...

The GoPro HERO 6 & 7 Rubber Suit holder is a bit of a pain to print but it works and has enough room for long LiPos. ... [Check out the GoPro HERO 6 & 7 Rubber Suit here…] [HERO] [HERO]:https://www.thingiverse.com/thing:3167362 [Check out the GoPro...

Single-color and MMU multi-color versions are included.Required materialsEach lock uses eight 8mm X 3mm (D x H) round magnets and can be attached to the enclosure with two or four 3.5mm screws.Printing instructions The lock has been designed for...

Test this :) !!! Printing Info : - use a materials that is stable in water (I used PETG).- use support from build plate only. - optionally add more part cooling to make support removal more easy. Why I made it : I made this...

It is parametric and you can change the angle that is printed within Solidworks by going to the equations section and telling it how tall is your frame (370mm) and how far out will the all thread touch the wood (mine is 200mm). From that the equation...

As this model is in 1:10 scale, it is rc controllable and not a quick print!This is my second 1:10 scale “Lanz-Bulldog” tractor. Many parts are quite similar to my 1:10 scale “Eilbulldog” but I have optimized most of them. The interior is quite...

Since publishing the Filament Server System in 2013, I've sought a more efficient system requiring less printing, fewer loose parts, easier assembly, and simpler spool changeovers. When creating the pipe-based, wall-mounted Spool Storage Rack last...

You can do finer adjustments to the tolerance by putting some scotch tape or masking tape on the inside of the shell wall. Print the shells with the flat bottom on the build plate at 0.3mm layer height. You might want to add a 2 or 3 mm brim to...