3d printed articulated action figure

 I printed all the files in PETG.  Files...

Not only was it my first real model using FreeCAD - which I'm still learning - but it's also my very first attempt at designing printed screw threads. True to form, I didn't start with something simple where you just look up standard threads on a...

I used a long stem (6 or 7mm) tactile switche I bought in as part of a set from Amazon. The code I used is here: https://gist.github.com/Arudinne/c540aa2470599e2cc87307d384696c95 A video of the patterns I used can be found here:...

(I've worn them and they're actually not uncomfortable) List of the parts needed to print: 2x Nanami_rim.obj 2x Nanami_pads.obj 1x Nanami_nose_bridge.obj The rims are perfectly symmetrical, so don't worry about having to mirror them or anything. The...

Print quality is good, and I'll try a benchy and ghosting test later. The diameter of the sticks is 7.2 mm, but sticks with a diameter of 11 mm can also be used - they're almost three times as stiff in theory. 7 mm glue-sticks are fairly cheap, and...

I recommend using technical skills to assemble it, but don't worry if you're not a pro - it's still easy to print and assemble. You'll need some common 2.5mm screws, but make sure they're short enough or use small ones (5-7mm long). Alternatively,...

It does not produce a valid three-dimensional object that can be printed. ## tl;dr: * `trunk();` * F6 (render) * Export as an SVG in OpenSCAD: `File > Export > Export as SVG` ## Thanks All Bezier Functions based on the excellent work of...

For most standard nozzle 0,4mm the details are too small.Assembly:After printing, the dipstick and axle are inserted into the body.Then put the scale over the axis on the body, the moving parts can be "greased" with some liquid soap and a little...

  My will at first was to provide to the community affordable and easy to print by yourselves nameplates for the games who require generic tagging : Bloodbowl, Warcry, Warhammer Quest... And to help some makers adding a personal touch to their...

Once the project became generic, I switched to a list of pin numbers - these also must now be header pins numbers not GPIO pin numbers.Since I originally started this for the Raspberry Pi, here are some...

Note that tolerances were added where the original parts lacked them; these should print fine without scaling adjustments. You will need two Z Nut holders, which are included in the name as a reminder. A photo showing version 1 is provided, but note...

This is a little bit tricky as you may not touch the PLA printed support with the hot solder iron, and the space through the spokes of the outer support rings is quite limited. At last, mount the Nd-bearing magnets onto the axis. Use the hülse.stl...

The SKR v1.3 board mounts with M3 screws, directly into the printed plastic. The holes are 2.8mm diameter, so the M3 screws will cut threads into the plastic if you turn slowly with pressure at first. This works best with PETG, but also works with...

... to build this wheel. FOR PERSONAL USE ONLY - NON COMMERCIAL - NOT FOR RESALE COPYRIGHT Canary Sim Wheel Designs - ALL RIGHTS RESERVED You cannot sell the digital model, a derivative or adaptation of the model, nor can you sell prints of the model.

... points. This needs supports for building (you might try flipping it upside-down to check if you need less material - this depends on your printer). Also added full- and half-height main body extensions (these can be printed without support).

just in case the original author decides to take it down for some reason.) https://www.thingiverse.com/thing:3579224 The first 7 pieces replace parts in the original, so obviously dont print the originals of those. 8-11 are in addition to everything...

Sliced with PrusaSlicer, this design tests your printer's ability to print thin words without any layers on any side, showcasing its "floating" capability. Dimensions of the design: The base plate is 16 millimeters by 51 millimeters by one...

Print it with 0.2 and 100% infill. IKEA LÖRBY (EUR 9.99) is a USB charger that's powered by a 24 Volt power supply. It delivers a total output of 3.4 Amp and an maximum output of 2.4 Amp per USB Port. This makes it compatible with the Ender 3 power...

There is a bonus version for those who can print multi-material with a Zelda Triforce design. While the two hooks on the sides do a great job of keeping the handheld secure, the hooks on the bottom and top needed slight tweeks. The hook on the bottom...

That being said, Creality did an exceptional job with the CR-10 that third-party manufacturers can duplicate it using the cheapest, lowest-quality materials available, and still manage to print beautifully with some elbow grease. I say my CTC A10S...

https://youtu.be/LYm1B4P_h8A The two-layered planetary system of the "quick print" version was also only intended for calibration and demonstration. As you will find, the planet gears will twist under load and the clamping force will be quite...

... the key « f » for fillets.</p><ul><li>Draw a sketch an the top circle under the helix with a little rectangle who will « join » the eagle wings. By doing that, you will have a better print by having less retraction.&nbsp;&nbsp;Category: Automotive

I printed mirrored left and right (screw and wall bracket) so that the unwinding of the coil does not lead to the tightening of the retaining screw, but the screw remains in its position due to the slight resistance. I put a round piece of foam...

... list, the Max Travel of Z is 250mm. You can achieve 260mm but homing with the raise before descending will catch the fame corner on the X motor. Print Settings: Printer: Wilson II Rafts: Doesn't Matter Supports: Yes Resolution: 0.2 Infill: 80%

Instructions Parts Links: 1x 45-in cable link 12x 90-in cable link 13x 90-out cable link 2x offset-in cable link 1x offset-out cable link 1x extruder assembly Attachment Points: 1x E Motor Mount bracket 1x Front Attachment Point 1x Rear Attachment...

This part is printed with support on the build plate obviously. In order to make it fit, you have to take the housing off of the USB hub (just slip a dull tool into the gap and pry, there's no glue or clips) and trim off the plastic at the end...

This lifts the cables to eliminates contact and flexure of the cables during printing and it eliminates/obviates the need for chainlike cable housing to hold the cables and distribute/minimize flexing and possible wire breakage. ...In return, your...

I am making this design open source for people interested in printing for themselves, or that have the skill and the patience to put all parts together. There is some assembly know how required, and costs of the air pump, and tubing. The nozzle...

If you fix it for print, make a Remix, or send me a model for re-upload it\n\nA seductress is a supernatural entity in folklore (traced back to medieval legend), that appears in dreams and takes the form of a woman in order to seduce men, usually...

Components used: 8 x 9G Servo motor - Link: https://www.banggood.com/TowerPro-SG90-Mini-Gear-Micro-Servo-9g-For-RC-Airplane-Helicopter-p-1009914.html?p=E01411629100201406T1&custlinkid=359550 1 x White LED - Link:...