3d printed duplo

The biggest part is 118mm x 141mm, so this can be printed on way more printers than the big version. There are now two LEDs per segment instead of three. There won't be much documentation as it's basically the same thing - just a bit smaller. So if...

• The snap fit between the chassis and body cover is both very tight yet very fragile due to the print direction of the cantilever joints. Take care when attaching - I also use a screwdriver to pry them apart when needed. • I ran into an issue...

I recommend printing the monorail at 100% infill. The sign can be added into the right ear from a slit between the ears. The sign is based on the one that was on the Epcot Ball from 2001 to 2007. The sign was modified to add in open area below the...

I wanted to fit some lighting to the Kossel so I could monitor overnight prints remotely without having to leave lights on all night. The Neopixel range of addressable strips and rings seem to fit the bill as they only need a single data line for all...

Thicker panels and prints good now in 1/25th scale *UPDATE: 10/09/21* Uploaded a revised truck bed, this time with wall supports, Rev B *UPDATE: 10/06/21* Revised the truck bed, made the walls a little thicker and smoother, Rev A for both Pro Street...

When I printed it, I placed the A blocks right next to the B blocks in the slicer, so they were already joined together. Here are the coordinates in case you want to get neighboring pieces, or need them for whatever reason. I'm also including...

This allows it to be printed standing on its side with less support. With no supports, the top will have some drooping/stringing and some cleanup of that will be required. With supports there may be some residual support cleanup required. I use...

I used a long stem (6 or 7mm) tactile switche I bought in as part of a set from Amazon. The code I used is here: https://gist.github.com/Arudinne/c540aa2470599e2cc87307d384696c95 A video of the patterns I used can be found here:...

The gray and orange caddy shown here was my prototype and a number of improvements have been made to the design since it was printed, mainly regarding the fit of the deck boxes, keys, etc. The largest dimension on this is 9.7", with the height...

Thin "windows" are designed into the forward and bottom surfaces of the backpack, which can be cut away after printing to increase much-needed airflow. PRO-TIP: The DTX03 ships in standard-definition mode, but it's capable of recording nicer video...

Migrating from thingiversehttps://www.thingiverse.com/thing:4387788 Adapter to connect a removable 150mm flexible duck to a 250mm Ceiling Extractor to remove Solder / Flux fume.designed to be printed on a CR-10S PRO , so a 300X300 bed...

You'll need to print two of these, but don't worry about mirroring since this is symmetrical and so is the gap it fits into. You will need to upscale this object by 12.7 times or with an X, Y, Z of 101.6mm x 31.74mm x 10.38mm. With this scaling,...

Since I haven't printed all revisions, this remains a Work In Progress, but in reality, I don't plan to make changes anytime soon, and any updates will need to wait until more Rubbermaid containers are purchased. 10/29/2019 - It's been found that...

... convenience. Feel free to modify them however you please and post remixes for the community to benefit from! Print Settings: * Printer: Flash Forge Creator Pro * Rafts: No * Supports: Yes * Resolution: 0.200 microns for most parts * Infill: 40%

The bottom has been printed, and it works. My bolt holes were a tad loose, but that was all. I have since decided to move on to a rear-mounted box as seen in a recent Teaching Tech video. (06/11/2019) There was an issue with the 1x10 dupont slot on...

**Instructions** - Print one copy of the Piédestal and of the Cercle cranté (that's pedestal and notched circle for you english speaking people) and six copies of the Secteurs (sectors). I advise to join the sectors by twos (a simple adhesive is...

... right?) 10. Do the reverse of Step 1 & re-level bed. 11. Move z limit switch up a few mm's/until nozzle doesn't crash into bed when homing. 12. Print away! ... Video: https://youtu.be/IBlSbVZZRGk Any feedback, questions or comments are welcome!

Stylized Earth Python Generator is a Cinema 4D scene that enables quick creation of a unique representation of Earth by leveraging inspiration from dot matrix printing. Instead of ink dots, elements are created with mesh that wrap around a sphere. In...

A complete unit requires 1x Post (Lower), 1x Post (Upper), 2x Sleeves, 2x Through bolts, 2x Bearing Cups, 3x Arm (Hole), 3x Arm (Peg), 3x Arm Clips, 3x Brackets, 3x Rods, and 6x Hands to be printed, with 2x 608 bearings. Optionally included is an...

Required components: 1 x high-torque geared motor (I used 5 rpm, it's slow but will never have problems with moving my blinds) 1 x L298N motor controller 1 x ESP8266 (I used a Wemos D1 Mini) 1 x micro-switch A couple of 3mm screws for the motor and...

... a piece on the bottom to prevent the gap on that side. Hopefully it won't interfere with putting the cable in too much. Update: I goofed on the previous one, and forgot to include a hole for the power cable, so now I'll have to print a third time.

It may be a cap or expansion space.C1 - A cap with a solid top.C2 - A cap with an opening sized for a voltage display.C3 - An expansion space to accomodate a device up to 80mm x 50mm x 17Dn - A cap for a C3 componentD1 - Solid capD2 - Cap with...

For screws, you can use either two nuts per leg (one above and one below the printed hole) or M3 threaded inserts. I designed the screw holes tightly so that M3 screws alone are usable, but be aware that adjusting the screws multiple times will...

When printing these models, it's highly recommended that you use Cura's "Horizontal Expansion" feature with a negative value. A value of -.12 works for me. If they are still too rigid, try -.15, then -.20, and so on. Introducing BuckleBoards, a...

As of now, I am awaiting a new Creality hotend as well as the heated bed, and 165mm glass surface before printing can commence. However, movement systems work well. HARDWARE REQUIREMENTS Electronics: NEMA 17 Motor - replacement z-axis motor ...

From strength and flexibility, PETG seems suitable as the print material. While PLA can also be used, it is hard and brittle, so it may break easily or cause problems with the fit of the nose frame. Initially, I thought of attaching paper to the...

Print Settings Printer: Other Rafts: No Supports: No Custom Section How I Dreamed Up This: To make this, you first have to create the base of the ship using a rectangular prism, then use the triangular prism to make the keel of the ship. Next, you...

# Print Instructions: Be sure to use supports for the wall pin and the gun holder. Take care to clean the supports and leave a smooth finish on the gun holder. I set this up so the gun points to the right to hide the screw holes. If you want to...

The two silver rings are Dekco and can be printed in PLA. The holder itself in PTEG+ for absolute stability All you need then is a bike GPS mount from Amazon. then an M5 countersunk head, a nut and a snap ring. The 3 original screws from...

... to control the servo yourself, so don't ask. Added servo_holder_only.stl on request. This is the servo holder without the space for the electronic components to control the servo. I did not print this servo only variant as I don't need it.