40ft container high cube 3d models

SKU: 17HS15-1684S-HG50 (Tilt) I purchased mine here: https://www.omc-stepperonline.com/precision-planetary-gearbox/nema-17-stepper-motor-l39mm-gear-raio-501-high-precision-planetary-gearbox-17hs15-1684s-hg50.htmlCamera supportA camera swiss plate...

**Filament:** I used high-quality Geetech(Sunlu) PLA filament in black to ensure a smooth print finish. **Temperatures:** The ideal printing temperatures were set at 215C for the nozzle and 60C for the bed, ensuring excellent adhesion and minimal...

Introduction This is a high-quality wolf model with 4K UDIM maps, fur, rigging and three realistic animations. The model has a realistic muscle structure, a complex hair system created in Blender which makes the hair natural and realistic, and a...

The Auto-Rewind Spool Holder for Repkord's RepRack provides slight tension on your filament when feeding into your printer, reducing slack when retracting, especially in the case with multi-material print mechanisms such as the Prusa MMU.Featured on...

(The top plastic piece is the part that makes the case high-profile.) You will need a credit card, spudger, or some other plastic wedge to work around the perimeter to prise the top piece from the bottom part of the case. (c) Once the top piece is...

In this case, please contact me, and I can save files at high values for you. This hand vise hand tool clamp universal holder is a fully solid-state version for 3D-printing, which means it's not a scan version. You can see the contours of the models...

They can shoot a projectile at high speeds, even at low pressures, and may explode if not made correctly. I take no responsibility for injuries or damages caused by this project. The piston is sized to work with 1-1/4 inch schedule 40 PVC pipe. Be...

You may have to use a tiny support for the crossbrace of the extruder cooling fan duct, depending on your printer.If you print the 5.7mm standalone backplate version, you have to pause the print at 5.2mm in order to insert two captive M4 hex...

In this case, please contact; it is possible to save files at high values, but this will give a sharp increase in file size. This is a fully solid-state version for 3D-print; this is not a scan version. At the photos you can see the contours of the...

The classic style bed will be better for "high positions" of the body over the chassis, normally in a crawler or monster setup. Pro Smooth: After learning how to correctly smooth from low-poly I have invested quite an amount of time smoothing the...

The rail guides should be 10.6 mm wide, 4.2 mm high and 170 mm long. Use a precision knife to remove any warts on the prints and smoothen the holes. Thread lockers may be aggressive to ABS plastic, so if you use it, make sure to wipe off any...

Here's a closer look at the key features that make the v2 DJI O3 conversion canopy a true game-changer: ## **Impact-Resistant Engineering** The Five33 Tiny Trainer 3" v2 DJI O3 conversion canopy boasts an exceptional resilience to impacts, providing...

I used four pieces of pine 20x68x436mm (x2) and 20x68x381mm (x2) To work out the wood lengths for different thickness of wood please take a look at the cheat sheet I made for you here: www.diymachines.co.uk/  ■ Glue (I used Wood glue...

These days, commercial filament is manufactured to very high tolerance. However if you make your own filament, it might be useful. Its called a prototype, because it's something you may need to tinker with to get integrated with your software and...

There is a button for doing tare when there is no spool on the holder.It works, but there are some things to improve:The load sensor is a rated for 50 kg which is unnecessary high and thus losing a bit of precision. Better to use a load cell rated...

If you use a high value, you might have to adjust the TableClipSqueeze and TableClipTaper if you don't want the clip legs to break.HookWidth: The span of the hook part. I made it adjustable in case some people want thinner...

You're not limited to using my parts to create custom cable ties, just keep them 1.4mm high and I suggest minimum 3mm wide for strength, Take a look at the "Hoopin_TPU_Cable_Tie-Triple_6_Springs_4_Hoops.stl" file, it's 3 cable ties joined by a 3mm...

## Go To Electronics: * $30 for OnStep controller * $20 3s LiPo battery ## Saddle * $40 for 2x small SvBony clamps ## Options on motors * $120 for 2x precision geared stepper motors 1:100...

The three pin configuration is highly recommended. 2 Pin: * 1911 - SLIDE.stl 20% infill. Supports on build plate. Drilling holes afterwards is optional. * 1911 - LEFT SIDE PLATE.stl 20% infill. Drilling holes afterwards is...

When used at high speeds, it is possible to print overhangs and small parts faster since with less effective cooling you would otherwise have to slow down in order for the part to cool enough between layers. The nozzle is visible and accessible. I...

9,5cm diameter 8,7cm high printed in 14 pieces (base, top, 6 bars, 6 panels) no need of glueing (but it's safer to hold it by the bars when moving, especially when tealight or candle is inside) you can additionally lock the bars with a thread (tie...

How I Designed This: OpenSCAD allows this battery tray to be highly customizable. I love OpenSCAD! This uses the great Chamfers-for-OpenSCAD library from SebiTimeWaster. While the library is included in this file, the library can be found at the...

Basically there are 2 ways: - either they are printed - on transparent ground, in a high contrast color - directly on the top part. Which involves defining filament change points in the slicer (both cura and prusa-slicer support that, I assume other...

Nothing should require supports, though the cheesy NVidia logo will require a few mm of bridging and there are a few 45-degree overhangs, so set your fan speed high enough to accommodate this. Assemble the ears and segments using M4 screws, nuts...

In this case, please contact; it is possible to save files at high values, but this will give a sharp increase in file size. This is a fully solid-state version for 3D-print; this is not a scan version. At the photos you can see the contours of the...

In this case, please contact me; it's possible to save files at high values, but this will result in a sharp increase in file size. This is a fully solid-state version for 3D printing; this is not a scan version. At the photos you can see the...

It looks nice but adds weight high up and tends to induce wobble. I printed my knob hollow. If you look at the layers in your slicer, you're likely to find that one side will have more weight than the other due to uneven distribution of fill. Go...

The top and bottom legs are 50 mm wide with a 60 mm high gap between them. The plywood throat depth is 70 mm. Tapering the upper leg is optional but I narrowed it to around 35 mm deep at the back end, starting the taper at 40 mm from the...

The Quest 2 controllers are offset to the side so there's a high chance of occlusion when not properly installed. Fix 2: disable gun and scope smoothing (Onward). ---- Use 2 x 10" pipes and 1 x 6" pipe It's important to use this exact...

So i tried 4 little springs on the center piece, but they were not strong enough support the shifting rod due to the high center of mass. I had to add 2 more torsion spings on the outside, which had an immense impact on the self centering action,...