Quickmount Reprapdiscount Smart Controller Case 3d models

  Add the Rotary encoder and the knob.Now it is ready for the mounting in the case.        Links: OLED and Rotary encoder connections described...

The recess is to provide a little clearance in case super glue was used to hold the crank to the brass shaft. Then line up the upper_leg, leg_pin_outside, and leg_pin with the crank and brass shaft. Use the leg_threaded_axle shoulder bolt to hold it...

In my case, there is an overheat issue with the extrusion stepper (it's hotter than other stock steppers), I think the new stepper has lower voltage than the stock one, I will add a buck converter to fix that. But it's not a design issue anyways. It...

&nbsp;Both a one piece rocket body as well as a split rocket body (with pin) is supplied in case your printer Z-height cannot print the one piece. &nbsp;My print contains the two piece rocket body, with the seam hidden by the middle rope.</p><p>4 -...

As of this writing, there are just some details that procedural textures couldn't achieve yet via Cycles or Eevee nodes, that's why we decided to use Image Textures instead which are in most cases, faster to render and more manageable. But the Vmats...

For the whole system you need additionally: Car battery which is minimum 300cca (There has been said minimum 200 is enough but just in case ;)) You should keep the battery full as far as possible. Timer module:...

  It's certainly not enough time to take photos when you are working by yourself!Cut the top to the finished size you require - in my example it's 352 x 272 mm which is enough to give a few millimetres of overhang, in this case I like the angled...

PHOTOS --------------- In case any of the photos are not self explanatory, here's what they show: 1. Installed auger, looking into the hopper. You can see that the screws protrude through the other side of the shaft. That's a good thing. We don't...

Thank you Werner!Thanks to darktiger for his print and picture of the keytag “Ana”.Printing:In case you want the two-color look like in the pictures, introduce a filament change in prusaprinters at 2.2mm for the fast-print keychains like this:Or for...

In that case, use M2 hardware and print the parts that end with “M2”. Only the Skadis T-Nut &nbsp;and the Mounting Plates are different depending on the screws you use. The Arms and Flappers use M3 hardware.</p><p>&nbsp;</p><h3>Printed...

If you still have problems, then please visit the original thingieverse publication (https://www.thingiverse.com/thing:4267901) where I have added some custom parts for such rare cases. Please adjust temperatures and material parameters for your...

The frame will accommodate phones up to 170mm tall x 84mm wide, and cases up to 13mm thick. It can be used with phones as short as 130mm.</p><p><i><strong>Lighting Arms</strong></i><br>The lighting arms screw into the corners of the frame with the...

If you have problems getting the pieces to fit together, you can adjust your slicer settings, or in an extreme case, modify the `dual-reel.scad` file. Increasing the `radialEase` variable should make the objects fit more easily, and decreasing it...

* it will automatically include the EXTENSION at the end for ease, so just leave it out * if this value is “PLATE” (not case sensitive) then it will extrude the SVG to "platethickness." * x = x coordinate of the COLOR.svg * relative to the top left...

In this case, please contact, it is possible to save files at high values, but this will give a sharp increase in file size. This is a fully solid-state version for 3d-print, this is not a scan version. At the photos you can see the contours of the...

Using the following options: qr_size = 37 qr_bottom = 1 obj = 1 code_flip = 0 tag_height = 80 qr_y = 0 qr_x = 0 tag_width = 80 qr_tolerance = 0.001 case_thickness = 1.8 add_sub = 2 per_h = 10 per_w = 3 round_corner = 2 tag_thickness = 3 corner_num =...

 Part 4 and 5 are ment to hold with carriage bolts to the backrest, these should point with the head to the rear, accordingly the...

Please **PLEASE** label **EVERYTHING** before you start throwing wires into it, and consider having extra spare parts before starting this project in case any permanent damage is done to the MKS board or any other sensitive component. Use this...

Well, there are a lot of really technical issues you can read about for yourself and much back-and-forth about which is best, but at the end of the day I figured if I was going to take the time to design an assembly, it only made sense to have it...

In both cases the LEDS color glitch very badly. As they flicker they show random incorrect colors. Even worse if I just opt for white which either also color glitches or fails to even reliably light up. Code is the same in all boards and nothing...

(slider would go in the middle, in that case). V1 is better for most else. -Use the pictures along with the instructions, if needed. It’s free and has very low latency. Very high-quality image and good FPS. Touch supported. -For wired...

Just in case this does not get updated please check the thing files themselves for available options.Installation1.I have also uploaded some basic installation guides for both the stock &amp; the V6 versions. The guides only cover the basics to get...

In this case, please contact, it is possible to save files at high values, but this will give a sharp increase in file size. This is a fully solid-state version for 3d-print, this is not a scan version. At the photos you can see the contours of the...

... is another free 3D model made available for you. Designing, testing, preparing, uploading and maintaining my models is effort. In case you enjoy them, please send a donation using the coin button in the top right. ...Thanks a lot!</p>

In all cases, the model represents a land area of ​​10x5 km. The base is level 0 above sea level and is made from contour lines of 10 m.</p><p>These models are made from the Topographic Base of Catalonia 1:5,000 of the <a...

In this case, the ASUS Republic of Gamers (ROG) decided to name one of its monitors after John "TotalBiscuit" Baile, a popular gaming personality who passed away in 2018. The monitor is called the ROG Strix XG438Q, but it's not just any monitor. It...

language support (Hemera mod, from E3D Tuto) configuration_prusa.h Line22 : define NOZZLE_TYPE "E3D_Hemera" // Hemera // Developer flag define DEVELOPER // Printer name define CUSTOM_MENDEL_NAME "ProTubeVR Hemera MK3s" //Hemera **Line42: // Extruder...

&nbsp;I included printed versions though in case you cant get them.Aluminium Mesh - the sides have a mesh insert. &nbsp;I used some from a car shop, normally used to back body work repairs for my original project. &nbsp;I modeled some up but its the...

In case you lose track of how many printers you have or just want to dress them up a little bit.Supports are painted on the inside and easily removed.Quick and easy printDesigned on...

If one side is up the other side is down), and the nut traps in the leg_drive_disk will be on the side toward the frame.&nbsp; Turn the main drive gear to make sure that everything rotates without binding.&nbsp; Then tighten the M4 clamp nuts on the...