SciFi Control Room 3d models

(download here)This image uses Max.K's latest Zerobot Pro control interface changes. To use it, just connect to the "zerobot" WiFi network using the password "zerobot1" then browse to this address: <a href="http://zerobot/">http://zerobot/</a> or <a...

... Also included are joystick spacers so you can set the stick to your desired height and a pcb mount for Brooks ZeroPi & UFB* control boards (both should be the same size YMMV). Remixed from the Full Size Arcade Stick by jasondemeter (thing:3514821).

This allows much finer control than rescaling.&nbsp;MiscIf you want larger or smaller cups, rescaling should work fine. Just make sure you use the same scaling factors for all cups. Also, upscaling in the Z-direction will increase the friction area...

His evil acts in Derry remain unpunished, as "It" adversely affects the consciousness of the local population and controls it. Pennywise can appear in any guise, but the likeness of an infernal clown is a favorite shell for him. Other forms are taken...

The unofficial interpretation However, there is another theory that Pakal is actually sitting in what appears to be a spaceship and that his hands are on the control board. In addition, next to his nose it is possible to see an artifact that is...

Adhering to strict quality control standards, our team strives for authenticity and detail in every corner, even at older versions of V-Ray where potential disparities might arise. High-definition preview images are rendered directly from output for...

They are a little less controllable and do tend to need frequent adjustment. Older kids may want the stability of glued parts. I printed 2 of each file in 2 different colors and had the ability to build 12 full sabers for a party of 10 padawans....

Solar Tracker (automatische Sonnennachführung) mit ESP8266 Bauteil aus mehreren Komponenten: Boden mit Bodenplatte und drehbarem Deckel mit Motor und Zahnrad Wandteil mit Motor und schwenkbarem Solarpanel https://youtube.com/shorts/3H7bXHFrhLs...

Specification - 13.5cm Width x 5.9cm Height x 2.4cm Depth - Raspberry Pi Zero 2 W powered - 2.4 inch 320 x 240 SPI screen (capable of 60fps+ with fbcp-ili9341 drivers) - 3000mAh battery (providing 4 hours+ gameplay time on a single charge) -...

for my build I wanted a night vision camera so I used a raspberry pi NOIR camera and IR Leds along with a 3amp 12v to 5v convertor, 5v feeds the PI and 12v powers the IR ring. I printed the body and other parts, mounted the sensor in the sensor mount...

It just fits inside an IKEA Lack enclosure that is double stacked (except the Mk3S control panel sticks out a little).It is also far easier to feed new filament. The MMU2S feed tubes are shortened to under 10CM and there is more space for fingers to...

Application of UV lights to foods not only helps indicate potential defects in food, it also helps remedy the problem by killing these unwanted pathogens and ensuring that each food item meets consumer expectations and quality control.The...

Electronics ----------------------- * [BIGTREETECH SKR PRO V1.2 Controller Board 32 Bit](https://s.click.aliexpress.com/e/_9v6wUv) * [4pcs TMC2130 With SPI](https://s.click.aliexpress.com/e/_9iVnvX) or [4pcs TMC2209 V1.2 Stepper Motor...

Things kinda spiraled out of control from there. Quickly. I decided early on that I wanted to be able to easily switch back and forth between vanilla OpenBot and OpenBot: Beyond Thunderdome. So like the tank treads I designed, everything can be...

I simply added some control for the trigger buttin ad the brightness adjusting potentiometer. Create the death star We work from top to bottom. Add the first five inlayes (1, 2, 3 ,4 ,5) to the top shell - the one without an hole in the middle. In...

All you need is a flat surface to put everything on.For controlling the machine I have use the widely known and very well done GRBL firmware, running on an Arduino Nano. I recommend the really excellent project page from Arnab Kumar Das, who has done...

The controller from the matrix is a arduino nano. The hole design is extremely simple so that it cannot go rong. All the parts need to be printed at 20% or higher, the ring need to be printed at 100%. This is the code to set the time on the DS3231:...

You can start by either renaming the files included in the project from DFPlay.cpp.txt and DFPlay.h.txt to DFPlay.cpp and DFPlay.h respectively or you can download them from their GitHub [This step is no longer necessary as I have uploaded the files...

During its circa 8-year production time, all stock should be irrigated, clipped and treated with controlled-release nutrients to optimise health.Quickset hedge"Quickset" redirects here. For the lock manufacturer, see Kwikset. For the software and...

Finally you will get absolutely flat top surface with the labels of different colors inside it.4) Don't go away from the printer while layer 1 is printed: you should control that the quality of the labels is good before they are covered with layer 2...

We use an Arduino microcontroller to first process the read the current time and then align the segments out accordingly through a motor controller.&nbsp;This piece is a continuation of work I did before I had a 3D printer here. I brought the Prusa...

This is not the nature of computer controlled projects. The software is as important, if not more important than the hardware. I've include a zip file that contains my code to make Ninja walk and roll. I encourage all builders to really digest the...

My threads are based off of the ISO metric standard (https://en.wikipedia.org/wiki/ISO_metric_screw_thread). Lens Notes No focus or aperture controls are available via this adapter, but see my other designs (https://www.thingiverse.com/thing:4902657)...

Our facilities include: * Modern production lines equipped with cutting-edge technology * Advanced quality control systems to ensure exceptional product quality * Comprehensive testing laboratories for rigorous testing and evaluation * Well-equipped...

The SSD controller sits directly under the CPU of the raspberry pi and it gets hot! So... I'm gonna add some more ventilation to the base and upload a new version. EDIT (20/12/2021) - Extra ventilation solves the issue. I've added 3 more STL...

triangle or square.Future Plans:I would like to add a speed controlled DC motor as an option so the travel speed can be tuned.Print SettingsPrint in orientations from 3MF files.Supports:NoResolution:0.35mm Layers, 0.6mm NozzleInfill:YesNotes: Pulleys...

...When a dust storm strikes, controls from Main activate the massive turbine. This gigantic structure sucks in as much air (and dust) as possible, removing the majority of the dust from the interior of the walls. However, the dust has to go somewhere.

There is a little passthrough on the toolhead mount to secure these wires with a ziptie.I am using the Klack-Probe-Macros from GitHub to control everything. There was just more informataion available to get it working the way I wanted, as they are a...

A 0-10V dimmable light works through the use of a DC control signal that ranges between zero and ten volts. The basic idea is that at 10 volts of input the light is at its brightest level with 0 volts being the lowest possible dimness setting. The...

TL;DR first: Welcome to my Overhaul of the Creality Ender 2! Im starting here with version V2 (V1 is only in one picture; there was too much wrong with that), which comes in 2 iterations/stages: ++++++++ Stage 1: ++++++++ changing out the Heatbed to...