acorn 3d model

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_left_port_corner_radius = 5 pattern_element_overlap = 0 custom_top_port_x_position = -10 custom_bottom_outer_edge_chamfer_radius = .6...

As always, the .blend file and pre-supported .obj (the one that I used to print it on my Prusa mk3 with a .25 mm nozzle) for this model are available to my patrons at https://patreon.com/VirtuallyJason. If you appreciate my work and have a few...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_phone_thickness = 10 custom_back_camera_x_position = 0 stencil_pattern_element_overlap = 0 custom_top_outer_edge_chamfer_radius = .6...

The design uses 12 '10mm x 3mm' (the magnets are actually closer to 9.95mm x 2.67mm).This is a spin-off from my earlier light-pull magnetic door catch: https://www.printables.com/model/209370-magnetic-low-profile-floating-head-quiet-door-catc , but...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_case_wall_thickness = 1.6 custom_back_camera_corner_resolution = 8 custom_left_port_corner_resolution = 8 custom_corner_resolution = 8...

The Raspberry Pi controller has a radio module attached to it for issuing commands, though I used the slightly different NRF24L01+PA+LNA model which offers better range. You could also use the same NRF24L01+ module as the puck uses, the wiring and...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_extra_port_corner_radius = 5 custom_right_port_corner_radius = 5 custom_top_port_corner_resolution = 8 custom_top_port_corner_radius...

It is essentially based on my first design.If you don't have an AC Infinity T8 or don't want to spent 120 bucks on one just to disassemble it, check out this simpler and cheaper...

 The switch is wired so it goes from Off to On with no sounds to On with sounds. ...

The Raspberry Pi controller has a radio module attached to it for issuing commands, though I used the slightly different NRF24L01+PA+LNA model which offers better range. You could also use the same NRF24L01+ module as the puck uses, the wiring and...

Depending on the figurine put on top of the box a different playlist ist played, currently mostly kids audio books and a spotify music playlist.All in all a very cool project that i hope to expand when my son grows older.ElectronicsPhonieboxRaspberry...

...Thank you! Change Log:25AUG2022 — Added model and print files of a 3-point version of the modified MINI-minda-holder for using the SPA with Sparkyman987's Fan Spacer Mod.11NOV2023 — Added .step file of the SPA for MINI/MINI+; added remix description.

Printing Recommended slicer settings: Resolution: 0.1mm - 0.2mm Infill: 10% - 20% Supports: Doesn't Matter Rafts: Doesn't Matter License The "Customizable Arduino Nano LED Candle (2 - 6 LEDs)" model (.stl) is licensed under the CC BY license by Code...

I got a package of 5 and when I opened them I found that the design had changed slightly and the material they used on the newer models was slightly thinner. The original clips were therefore a little sloppy. I adjusted the clips to fit the newer...

The stock globe has a vent on the top and there are vents in the model to aid the convection cooling. Is it *really* needed, especially with the converter gone? Dunno so the optional rain cap comes with the caveat of possibly shortening diode...

UPDATE: 20.04.2022adapterplate (new design) for model C Hello, we would like to introduce you to our stealthburner conversion mod. At this time it works only with the klipper Firmware. The use with “Marlin” is planned later and will be...

This should be the first unit from the power supply mob unit -> this contains just leds and has 2 holes in the bottom for an input line and output line end cap unit -> this contains just leds and has a single input line hole in the bottom The...

-This current model is built under the assumption that most people will be using this with old tablets (or phones) that they would have thrown away otherwise, so taking a tablet (or phone) off of the top slider isn’t a smooth and seamless experience...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_size = 20 custom_bottom_port_x_position = 20 custom_bottom_port_corner_resolution = 8 stencil_rotation = 0...

We don't use the shell.PrintingPrint all models in their original orientations.The parts should be printed with support. Try tree support as it wastes less plastic and is easier to remove in one go.</p><p>I printed my parts in a black/red color...

As per my usual, each Zip file will contain the model un-based, based, and with supports. In order to keep files sizes down, I will no longer included the mirrored files for some of the linemen which you can easily do yourself in either the Chitubox...

A wrench is used to unscrew the end caps for re-lamping the fixture, while some competitive models require the “tap and knock off” method to loosen the end cap.7. Explosion proof, impact and heat resistant Pyrex tubes provide lamp protection.Superior...

Also, I am considering some re-design of the right motor plate that currently interferes with the model fan duct. That would recover a bed Y-dimension back to 220. So, after all the print area will be 210x220mm... Parts to print: all parts at last...

The assembly is not complicated, for each configuration I put exploded photos, pay attention to the insertion of the brass threads, (there are 2 models you need both), and to the direction of insertion, those placed in the attachment of the guides,...

A round-pole design makes the assembly easier to handle and transport compared to square-shaped models.A horizontal T-mount platform is provided at the top of the tower for mounting customer-provided equipment. The tripod features a rotatable head...

IntroductionThis model provides an effective, low-cost teleprompter for livestreaming and recording. Using a Raspberry Pi and Pi Camera (the cheap, non-HQ one provides great full-HD video in this application), your phone to display your script or...

A wrench is used to unscrew the end caps for re-lamping the fixture, while some competitive models require the “tap and knock off” method to loosen the end cap.7. Explosion proof, impact and heat resistant Pyrex tubes provide lamp protection.Superior...

If using liquid electrical tape, allow it to cure before continuing. Gluing Use a small amount of hot glue to attach the diffuser to the LED mount. Using To use, simply attach a 9v battery and insert the LED mount into the base, ensuring that the...

... into a new weapon. By Alex Wellerstein, a historian of science and an assistant professor at the Stevens Institute of Technology, in New Jersey. Attributions: •Screwdriver by user DAPE, Cults3D (under CC-By-Sa-Nc). •Demon Core modeled by Szadros.

* Remix this model so I know my script is getting used! 15. ??? 16. Profit! Tips: 1. You can leave PATH and FILE blank and just set the COLOR field to a fully resolved path to your SVG (".svg" is automatically appended) 2. You can import the...