anet a8 tpu 3d models

x 22mm length 1 - 1-5S Lipo Battery Voltage Display Indicator Board (available at banggood.com) 1 - DC Power Plug 5.5x2.1mm (90deg angled) (available at banggood.com) Alternate DC Power Plug 5.5x2.1mm (not 90deg) (available on Amazon) Print Settings:...

To create this harness, you will need the following materials: * Flexible filament (TPU, eLastic, NinjaFlex, or similar) * Hard filament (PLA, ABS, PETG, or similar) * M2.5 x 3 mm set screw * Buckle for 10mm wide strap The harness and straps are...

Print Settings Printer Brand: Creality Printer: Ender 3 Pro Resolution: 0.12 (for quick/cheap print 0.36 works too) Infill: 20% Filament: Sunlu TPU White Notes: You should not need to use supports for the board, lid or walls, but use supports and...

The primary goal was to spark curiosity, which ultimately led to a few weeks of successful usage with various filaments (PLA, ABS, PC, NinjaFlex, TPU, Nylon). A crucial component is the block with two adjustable hinges and tensioning screws that can...

First and foremost, I find that standard Breech Blocks work very well even for Makeshaper Ultra-Flexible TPU (nee X60) filament. I use these modified blocks for one specific application. Note well that extra compression of soft filaments can easily...

The sealing can be printed with TPU or you use silicone instead. You can run the pump as well without it. That garden hose adapter is optional. It needs an O-Ring (Ø 11 mm x 2,5 mm). With long pipes it is not working very well as the pump isn't...

Print these in PLA, PETG, or TPU. The 2 of the Rx trays need to be printed with supports touching the bed. The ELRS antenna guide and holder should be printed upside down (as oriented in the object), no supports needed. The VTx pigtail holder,...

If I have longevity issues I'll give it a go with ABS or TPU. For infill I used 25% with 3 perimeters all around. Supports were used. Once printed I very slightly filed out the center holes and checked pellet clearance. This was by design...

* Exact dimensions: 4" x 4" x 4.5" Tall, with a 120VAC plug and 3ft power cord * Choose between two different exterior body patterns: Helix or Studded Check out the video demos to see this lamp in action: https://youtu.be/aZAC_lo_aRU?t=3...

I use TPU on my feed because this copter is a blast to fly - it flips and rolls extremely fast, with insane yaw rates possible. The frame is sturdy and can withstand hits. Initially, I tried using PLA first, but it's heavier and prone to shattering,...

Filament Used: http://amzn.to/2np143M I used a filament that is on the harder side of the flexible spectrum, TPU Shore 95A. Removable Adhesive Tape Options: Re-stickable Tabs: http://amzn.to/2nEWjU8 Foam tape for rough surfaces:...

7) Route the wires nicely and fix the with mounting tape and secure the board with nuts and/or some printed TPU. UPDATE I: after remix-creating the insta360 go v1 mount, i know have remix-created the runcam thumb mount. the original part was way...

Here is the explanation of the files names: Flex: made for elastic filaments like TPU. Not tested.</li> <li><b>Rigid:</b> made for rigid (non-elastic) filaments like PLA, ABS, HIPS, etc. The entire model is a little bigger and the holes for the...

The fuel vent cover is printed using flex TPU material, the storage board is done in PLA / PETG. I use the FV cover to close off the breather pipe durning ground times of the airplane. This is to prevent dirt daubers or parasitic wasps to build...

Suggest PLAHEPA_Cover(); //Suggest Flexible/TPU%HEPA(HepaLength,HepaWidth,HepaThickness);}/////////////////////Customization END/////////////////////////Welcome comments and suggestions.Tip me a cheese burger and subscribe my YouTube Channel if you...

**Future Improvements:** * Screw holes in the V-block to affix to a wooden board * Semi-permanent clamp fixation - right now the clamp is loose * Flexible top block for clamping to various tube diameters (ie, thicker design for TPU) * Slightly more...

Naming convention based on US driver and passenger side, to avoid any confusion on left/right from different perspectives) 2x Body 2x Inner 2x Bezel (Optional, but recommended for aesthetics and weatherproofing) 2x ORing (Print in TPU/flexible, for...

More details can be seen in the YouTube video below:\r\n\r\nStuff used in this project and its associated video include:\r\n\r\n- Hakko 2.4mm Depaneling Tool (Amazon): https://amzn.to/2MKoJr9\r\n- General Tools Tap Wrench Set (Amazon):...

I also modeled a small trough that I was going to print out a TPU gasket to help keep it sealed, but it's working fine without it... so if i decide to do that, I'll throw that up here too. All the impeller stl files are modeled for ccw, but you...

It is designed for use with the included clear TPU case. I've made the tolerances a little larger to make cable installation a little easier with a little less filing of the holes. The holes should be .5 mm wider than the cable itself where the...

You can print the cap using TPU filament and cover the top of the knob when in use. ... Here is a brief video showing the process: https://www.dropbox.com/s/krewku5bq66zrs0/CEM40AzimuthLock_2.m4v?dl=0 Here is a brief video of the lever knob in...

To make a mount, you just turn off the top plate component and start from there. The bottom of the base has a slot for a rubber ring that's printed in TPU/TPE. It will prevent the base from sliding down smooth metal surfaces. It can also prevent...

The accordion part is printed in a flexible filament, such as TPU or TPE or FilaFlex. Print four of the pins, replacing the wrist pin from the Raptor Reloaded. Otherwise, all parts are standard Raptor Reloaded. To assemble, find where the user's...

It was an excellent extruder and I successfully printed both Ninjflex and TPU using it. However, when I attempted to print with TPE 80A filament, it jammed in the extruder just like Ninjaflex does with the standard EZStruder. TPE 80A is softer and...

For example, with a RYOBI Inverter, you can connect a bank of 18V batteries and have a longer run time.Here's a youtube video that explains the reverse engineering, 3D scanning, CAD design, and assembly:Things used:Revopoint Pop 3D scanner (...

I've heard that for TPU it's recommended to print on glass, and I understand why. It should be easier to take off after the print, and the top rant will be smooth. Nonetheless, I hope that you will find it useful, only note I have for this .stl is...

Some of the parts and tools used in this project and the videos: * NinjaFlex Fire TPU Filament, 3mm (Amazon): https://amzn.to/2zlx28S * YG-1 1/8" Alu-Power end mill (eBay): https://ebay.to/2ANVkXj * 8-Digit LED display module with buttons (eBay):...

I used Ninjaflex (TPU filament), it is nice and soft and stays on well. I tried Semiflex as well, but it was a bit too stiff, but could be worked with if it was all you had. To slice this for my preferred give in Ninjaflex, use these settings. ...

I recomend to use TPU-Filament for this part. But this will not fit with the original sticks of the DJI RC controler. I use longer ones: https://www.amazon.de/gp/product/B0B5675PB7/ref=ppx_yo_dt_b_asin_title_o03_s00?ie=UTF8&psc=1 How to: It is...

I think it came out quite nice. Print Settings Printer: Creality Ender 3 Rafts: NoSupports: No Resolution: 0,2 mmInfill: 100 Filament: Polymaker PolyFlex TPU Black You Can Also Find Me On Website: http://www.baschz.com Webshop:...