ant pcb maker 3d models

A simple addon for Wanhao Duplicator i3, Cocoon Create, Maker Select, and Malyan M150 i3 3D printers that enables drawing of designs using any pen or marker. Parts List Included is a single file that contains all of the necessary parts, as well as...

Special shoutout to maker Benoît Lussier for providing QA printing and quality feedback. Benoît also provided the instructions for printing and applying the stripes. **Important** See notes below and extra text file about the stripes. Be...

Print settings: I've printed this fine on a MonoPrice Maker Select (Wanhao i3 clone) with no problem. I think 30% infill is good, but if you plan on doing full contact dueling, it wouldn't hurt or take much more time or filament to set it at 100%...

I just like to cover all bases due to the different skill sets of makers) Print instructionsRafts: Doesn't Matter Supports: No Resolution: .2mm Infill: 10% Notes:** Refer to the notes below for helpful printing and assembly instructions Building...

The original maker of the "On Air" box that this make derives from hot-glued these pieces together. It's not a bad idea. I had enough friction (and had it high enough from the kids) that it should stay without me gluing it just fine. Putting it back...

It's a cumbersome process that requires the maker to be present at the moment the lid model completes. I had to be there to turn the heater for the beds on immediately after the blank lids printed to prevent the model from releasing from the glass...

Special shoutout to maker Benoît Lussier for providing QA printing and quality feedback. ........................................................................................................... **Print Instructions:** Supports: Only...

... gear part of the worm gear must be drilled from 4mm bore to 5mm bore. Provided you're a well trained maker, this still can be done freehanded, but use a 4.5mm driller before you go straight to 5mm. ... -the whole rest is simple and straight forward.

These are intended to minimize print time and give the maker the opportunity to customize their case. The slots that hold these sides are 0.25" (~6.5mm) and the inserts are intended to be 75mm x 86mm. There are 9mm x 2mm recesses in the bottom for...

Special shoutout to maker Benoît Lussier for providing QA printing and quality feedback. ........................................................................................................... **Print Instructions:**Supports: NoResolution:...

Is This the Heart of Zosimus the Immortal, or Are the Writings Just Those of an Insane Murderer and Toy Maker? With the Whereabouts of the Box and Its Owner Currently Unknown, We May Never Know. ... As Always "Like" If You Do and Any Comments Would Be...

- Battery holders for at least 2 AA batteries - Switch, the clamp is sized for one of these little ones https://www.radioshack.com/collections/maker-parts-kits/products/mini-spst-momentary-switch-4-p - Bristles, I used the heads of 4 toothbrushes...

Special shoutout to maker Benoît Lussier for providing invaluable QA printing and quality feedback. Another shoutout to the guys at 3DBoom (Thingiverse id: 3db00m) for printing a beautiful copy of this model. A picture of the front view of their...

Print Settings Printer: Monoprice Maker Architect Rafts: No Supports: No Infill: Probably doesn't matter. I used 10%. Notes: The .stl files used to be 1.065x larger than the OpenSCAD source. This was the scaling I had to use on the last project I...

UPDATES: 2019.02.11 Fellow maker frankybuilds created a new Ender 3 mount solution for my fang, including versions with and without an EZABL attachment. It requires fewer parts and seems very easy to print. I haven't tested it since I don't own an...

I make it a habit to always have an M3 screw set on hand as they are so popular amongst makers and creators. You can purchase an inexpensive M3 screw set on...

The Hadley telescope by Maff is a great design that allows makers for an easy and cheap introduction to astronomy.There are lots of difficulties when using a telescope for the first time, for me one of them was trying to take a picture with my phone...

 If you have the proper filament colors, no painting is needed.The assembled model is 256mm tall.Enjoy!...........................................................................................................Special shoutout to maker Benoît...

If you want a little more detail, you can check out Makers Anvil's crater model here to give that planetary effect.The both versions look great as a models, but take them to your next game and have a fun time rolling all those nat 20's. If you don't...

What makers need is a totally new and novel 3D printable bearing means which can be really useful. Here is a new design by fractalgears.co for use in all of your personal design projects. The gearing system is versatile, highly efficient, and easy to...

... to tight the nut. This tool is created by Juan de las Heras and you can contact with me in this email Jdelasheras83@gmail.com You can follow my 3d print and maker account @3dprintsdiary on instagram https://www.instagram.com/3dprintsdiary/?hl=en

However, I decided to stick to machine screws and nuts because I didn't want someone to possibly be left with an unusable model they had worked long and hard on to paint just because the attachment interface failed due to poor method selection and a...

In conclusion, our rim system is made with versatility at heart to satisfy all types of game makers' different styles in addition with ease when changing everything over at any time we feel. At any time before the last end day we'll try best by way...

The .scad file is included with this model in case you want to modify any of its design parameters; more information on how to do this can be found in the PPP Puzzle Modeling tutorial.About the DesignerStewart Coffin has been called "the most...

This Challenge pushed us makers to create something remarkable - a place or famous thing on this planet. The thing I decided to model for the Challenge is not just a famous location to visit in the world. While it is a world-famous landmark, It is...

  Method 1: make gaskets using silicone compound Carefully read the instructions on the Customizable Gasket Mold Maker page (https://www.thingiverse.com/thing:2287689). In a very short nutshell: print the molds in ABS, as it seems to adhere the least...

You can use the dial indicator holder with the X-Plus and X-Maker too since they use the same extruder carriage, however you must edit the X, Y and Z values in the script to work with your bed size. <b>BOM - Bill of Materials</b> All you need...

But I wanted to make the design available here since I think there is a lot of crossover in the maker community between 3DP and CNC machining. &nbsp;</p><p>Due to the file type and size limitations on Prusa Printers I cannot upload all the files I...

or by using one of the following affiliate links down below (without any additional costs for you!). Gear that you need to build this fume extractor/absorber 12V, 80mm PC fan Amazon.de Amazon.co.uk Some screws for the fan Amazon.de Amazon.co.uk 80mm...

All feedback (especially from ball jointed doll makers and owners) is most welcome. This doll isn't jeweled, made of gold or magical but I hope it is something people will enjoy. Build instructions are to be found on Instructables:...