anycubic i3 mega simplify3d profile

 If you prefer an alternative power source it must be resilient to 1.6A stall current at 4.8V - 6V * A few bits of wire and some way to connect the parts.   In the examples here I have soldered plugs to the parts and made a small...

Other reasons are that steel doesn't care about heat, and it's lightproof Stripboard or custom PCB:I use a good quality white stripboard that was cut with metal cutting shears into a 53mm circle.Can't really tell you how exactly to make this, as...

Other reasons are that steel doesn't care about heat, and it's lightproof Stripboard or custom PCB:I use a good quality white stripboard that was cut with metal cutting shears into a 53mm circle.Can't really tell you how exactly to make this, as...

Round dowels are an option, but the square profile allows for more evenly distributed resin.500mm (or a bit longer) angle iron, aluminum extrusion or similar. Must be straight and have a valley the rod can nest in. Having two is better.Three (six is...

Furthermore, both Barrel Versions now come with an optional reinforcement rail, which makes the side profile look wider, as well as with engraved Caliber 44.Magnum text on the other side.Want to add some color to your sights? With the new...

**HOW I PRINT MUCH QUICKER WITH STOCK HARDWARE** -------------------------------------------------------------------------------------- Here are the two videos that give details on how I print much faster with stock hardware (changes to slicer...

I bought 30x100cm plywood, built sled at 5deg angle so I could cut them with easy and reproducibility.Plank cutting line - sled can be seen in the back.After cutting stack of planks I drilled holes and countersinks so bolts will flush nicely.After...

S4 Avant Lighted LogoThis was a design I created as a retirement gift one of my best friends (lovingly nick named The Douche, no seriously, lovingly).  He had recently purchased an S4 Avant so I found this to be a fitting tribute to the...

Check out his YouTube profile for additional information, but be aware that both systems only share the basic mechanism and not the actual measurements. The tool mount is basically a bracket which the tool gets mounted on. Hence the naming. :D I...

If you want the adjustable filament spool holder for the top, just head over to the original Prusa design and grab it. Oh, and as promised... HOW I PRINT MUCH QUICKER WITH STOCK HARDWARE Here are the two videos that give details on how I print much...

Fyrby Additive has tested this with 2.5kg spools as we do not have any larger ones currently available. Please note that we provide upgrade files separately in the profiles area so you can upgrade incrementally from any version.Which V-Spooler Should...

Features:No programming or uploading anything, just connecting wires.16 bearings (13 on 18cm version).Remote controlled.On\off switch (on remote and table).Reversible direction (with remote).Adjustable speed (on USB board).Battery and USB...

It Works, I have test it!FeaturesSecured BaseFor me, the most valuable feature is the low profile “Dock” attachment, It properly secures the controller to the table so there is no need to hold it.Four holes to secure itPush in to click-lockPush down...

It was sliced in PrusaSlicer 2.6.1, using the MK4 Input Shaper profile.Updates23 Feb 2024 - Added a 45 degree version with side tabs for screws by request. 3 Jan 2024 - Changed the name of the model to include “Friction Grip” to more accurately...

Basic profile: 25% infill, 4 walls, ironing top layers, ...Note: the included images illustrate the goals of the steps outlined below.[ ] 3D Print included stl files[ ] sunlu_fan_mount.stl -- Mounts 50mm blower fan and thermistor to rear of fan...

It is available at the link below: https://www.thingiverse.com/thing:3638866 A 12864 Mega328 ESR Transistor Resistor Diode Capacitor Mosfet Tester module with two adjustable DC-DC buck converters (with LCD displays). (pending, but available at...

The parts are made to fit to it only.)1x ESP32 micro controller board (No ESP8266 use possible because of its low specs.)1x USB power supply 5V / >=3A1x Micro USB cable 3m  Printing instructions:No supports or brim needed for all parts.0.3 draft...

All electronics compartment mounts designed to fit the Voron 2.4 DIN clip (print in PETG/ABS so the spring can flex).Custom STLs:DIN rail extension (optional - I ordered 500mm rail, these bridge the remaining 50mm)20A buck converter mount (optional -...

Power cut-off switch has been added.-Control panel redesigned to add a led switch and battery status monitor.-Added a led light bracket. .3mf files now have the proper print profile, such as ideal part position, layer height, fill and manual...

I have developed a collection of calibration utilities, all of them parametric or customizable, which are the ones I have used to get the results you see in the pictures with a Prusa i3 MK3S (not + yet) and a 0.6 nozzle. You can get much finer...

As always, the website above is where you go to see how everything comes together.Print SettingsPrinter Brand:PrusaPrinter:i3 MK3Rafts:NoResolution:0.2 mmInfill:15%Notes:You generally don't need supports except when printing a keyguard with raised...

Click below for the MK2/MK3 versions.MK2/MK3 Light Bar Files:MINI Light Bar: Standard version of the MINI Light Bar. File comes in the correct orientation for printing, no supports required. Smooth sheet required for tight fitment of front and...

If you want the adjustable filament spool holder for the top, just head over to the original Prusa design and grab it.Oh, and as promised...HOW I PRINT MUCH QUICKER WITH STOCK HARDWAREHere are the two videos that give details on how I print much...

***HOW I PRINT MUCH QUICKER WITH STOCK HARDWARE*** Here are the two videos that give details on how I print much faster with stock hardware (changes to slicer settings only): "BIG nozzles - HOW they (can) make your 3D prints STRONGER" by CNC Kitchen...

The provided 3mf files include a very good Prusa Slicer profile for Ninjaflex on the MK3S+, which is what I recommend for this project.CorksMany of the pieces are labelled “cork.” That doesn't mean like a wine cork, but rather the cork that's often...

Po cca 10 letech zkušeností s kutilsky vytvořeným prostorově úsporným pisoárem pro malé bytové WC (nejprve kompletně z nerezového plechu, oceněno v soutěži pořadu Vychytávky Ládi Hrušky, později vytvarovaného z akrylátové desky)...

You can follow the **Donate Here** hyperlink below or the papyal.com/donate link on my profile page. #### [Donate...

The Fellowship of the Ring Character Profile ============================================= **Legolas Greenleaf** Age: 140 years old (appears to be mid-20s) Occupation: Elf archer and member of the Fellowship Personality: Legolas is an elf with...

G CODE FOR YOUR SLICING ; Sliced by CANVAS ; ; *** Actual Slicing Settings As Used *** ; ; [Printer] ; extension = gcode ; costPerHour = 0 ; extruderCount = 4 ; firmwareType = RepRap 5D Absolute ; addComments = true ; g4pUsesSeconds = false ; fanPWM...