asus g20 open case 3d models

Thank you Werner!Thanks to darktiger for his print and picture of the keytag “Ana”.Printing:In case you want the two-color look like in the pictures, introduce a filament change in prusaprinters at 2.2mm for the fast-print keychains like this:Or for...

The original design needed minimal tweaking to fit my motor, but I ended up making some dramatic changes which massively improved its performance for my use case. I've put about 50 miles on this setup so far, and it's working perfectly. **This is...

In this case, please contact, it is possible to save files at high values, but this will give a sharp increase in file size. This is a fully solid-state version for 3d-print, this is not a scan version. At the photos you can see the contours of the...

I already had pre-spliced wires so just soldered them on with some excess just in case. Check the video by SonnyWheels mentioned earlier in the notes to see how to wire into this connector if you're unsure. I would recommend taking your time and not...

Just in case this does not get updated please check the thing files themselves for available options.Installation1.I have also uploaded some basic installation guides for both the stock & the V6 versions. The guides only cover the basics to get...

The diamonds displayed here at precision cuts on three D show case brilliance like the stunning beauty on a diamond set within, cut at a mirrored symmetrical display that has X dimensions mirroring at one and eighty two a shining example showcasing...

In this case, please contact, it is possible to save files at high values, but this will give a sharp increase in file size. This is a fully solid-state version for 3d-print, this is not a scan version. At the photos you can see the contours of the...

In this case, please contact, it is possible to save files at high values, but this will give a sharp increase in file size. This is a fully solid-state version for 3d-print, this is not a scan version. At the photos you can see the contours of the...

* The ball joint of the lower part of the shock is on the servo holder instead of being on Axle_Case_p4.STL. * The design of the shock is also different. See the section above where I propose a different type of shock. ### Part to pay attention *...

To attach to the bottom plate the best option is … 3M VHB tape, thin one. The screws of the air unit are unusable to attach it to anything (thin M1.4 screws) and using a TPU case will be bulky, heavy and add height.To sum up : tricky but...

In my case I have taken shorter screws (4x Ø m3x10mm). They are very short in length. Therefore, I recommend to take longer screws. ---- Step 6 - Preparing Electrics For this step you need: • 2x 4G LED bulbs (2,5W/250Lm) • 2x luster...

 Unfortunately, the headers on the board do not leave enough space for the head of the screws, hence the need for the Pico Mount Lock.8 - M2x6 ScrewsHolds each of the Grove Hubs (3 screws each) and the Grove Shield (2 screws)2 - M2.5x12...

In this case, please contact, it is possible to save files at high values, but this will give a sharp increase in file size. This is a fully solid-state version for 3d-print, this is not a scan version. At the photos you can see the contours of the...

In my case, there is an overheat issue with the extrusion stepper (it's hotter than other stock steppers), I think the new stepper has lower voltage than the stock one, I will add a buck converter to fix that. But it's not a design issue anyways. It...

In this case, please contact, it is possible to save files at high values, but this will give a sharp increase in file size. This is a fully solid-state version for 3d-print, this is not a scan version. At the photos you can see the contours of the...

The recess is to provide a little clearance in case super glue was used to hold the crank to the brass shaft. Then line up the upper_leg, leg_pin_outside, and leg_pin with the crank and brass shaft. Use the leg_threaded_axle shoulder bolt to hold it...

In this case, you won't need the "line-changer actuator" in the car but you will need electronics under each lane-changer track part, specially the "sensors" and the "actuator". There is a very good thing about the InfraRed lane-changers... You can...

In this case this will ensure that the GND will connect to the GND and the positive to the positive, preventing a short circuit. Now you have two separate pieces. When the stand is placed on top, forming a tapered cone, these pieces don't conduct...

In any case, using a 42MP body, such as the A7R II, stitching two (or better, three) shots will get you an approximately 48x36mm stitched image with about 84MP effective resolution. If you have a body like the Sony A7R IV, combining this with the...

Ideally, you have to have CR-Touch (my case) or BLTouch installed. Remove the extruder assembly, cut the wires in the center and extend them by about 120mm. Print and install the extruder repositioning bracket along with the extruder assembly in...

Avery, Logan, Riley, Cameron, Ryan, Angel, Jordan, Taylor, Morgan, Ariel, Dakota, Alexis, Skyler, Jamie, Quinn, Peyton, Micah, Harley, Parker, Reese, Hayden, Sage, Casey, Justice, Skylar, Kendall, Dylan, Emerson, Amari, Payton, Armani, Jessie,...

This extra thickness should help hold them in place.Model NotesAs mentioned above, this is based on GrabCAD models from Yauhen - Lego Skeleton Minifig Fantasy Era and Classic Lego Skeleton - and modified and shared here with their permission.In case...

Dice-Tray-Standalone.stl is just the little slider bit from the dice tray, in case someone wants to print those out to use without the whole character tray solution. So, once you've got them all printed, how do you fit them in the box? You can see...

  I do these as PLA on PETG supports as well set to SNUG:For more info on that bit, see the Prusa article on this at:https://help.prusa3d.com/article/combining-materials-xl_498103These are all printed with PETG, 0.2mm layer height and the supplied PS...

 Part 4 and 5 are ment to hold with carriage bolts to the backrest, these should point with the head to the rear, accordingly the...

In this case, please contact, it is possible to save files at high values, but this will give a sharp increase in file size. This is a fully solid-state version for 3d-print, this is not a scan version. At the photos you can see the contours of the...

Once the holes were drilled, I then held the assembled brackets and bars back up to the wagon and screwed the lath screws into the brackets to hold them in place on the wagon!NOTE: Since screw holes need to be drilled in the wagon for this design,...

...I decided to throw these in in case anyone else wanted to give them a try. Unsolicited Advice and Recommendations For the boards: Recommend printing in two halves and gluing together. Have included STLs with boards already split and ready to print.

 I've come up with the following solution:This little housing, for a Female HDMI connector, clips right on the Amiga case. I tried to design it in the A520 TV modulator style, so it should not look to much out of place in the 80' computer...

(slider would go in the middle, in that case). V1 is better for most else. -Use the pictures along with the instructions, if needed. It’s free and has very low latency. Very high-quality image and good FPS. Touch supported. -For wired...