atlas 10f lathe 3d models

Atlas 10F gears, 9-48a, 9-48b & 9-190 for reverse gear assembly Yet to be printed and tested! ... Now printed, fettled & installed, all working well

I was missing a set of Atlas Craftsman Model TH54 10F 10" 12" Lathe Wiper Caps so I designed a pair that incorporated oil cups to keep the felt wipers oiled for longer. ... As a hobby machinist I use my lathe very lightly, so having a reservoir means...

The Atlas 10F-81 is the support on the back of the apron that holds the miter gear that the running lead screw goes through. This is the same part as for an atlas 10 inch and 12 inch lathe. Also you will have to drill a 1/8 inch hole on groove side...

This is a model of an Atlas Mk.2 Lathe Bed reverse engineered to within a few thousandths accuracy give take for draft angles. ...Dimensions are accurate enough for most Home Shop Machinist purposes.

I designed and Printed this wrench to be used on my QC42 Atlas Lathe for locking the saddle and cross slide. This Wrench will probably work with other Lathes with bolts with a square head. The bolt size is .380 across. I used ASA filament because it...

Atlas lathes use a circular dovetail mounting system for attachments to the cross slide, such as the compound and milling attachments. There's a couple of pins that bear against the circular mount to lock it in place that tend to fall out when the...

https://youtu.be/NF554Jrok_w https://youtu.be/1LXigsea9dg Note that these dials will not fit all models of Atlas lathe. Please look at the dial measurements to ensure it will fit your lathe. This dial will not fit the older series atlas with 1/2"...

https://youtu.be/NF554Jrok_w https://youtu.be/1LXigsea9dg Note that these dials will not fit all models of Atlas lathe. Please look at the dial measurements to ensure it will fit your lathe. This dial will not fit the older series atlas with 1/2"...

Atlas 10" Lathe handed down guess 40s vintage. Model made on FreeCAD Step files transferred to OnShape to create Step assemblies and pdfs Almost all fasteners not included and taped hole not taped. Only the dials on the Compound and Cross slide...

I have made 3d printed lead screw bearings for my atlas 10 Lathe. I also made two styles, one wit h bronze bearing inserts and one with radial roller bearings. I was playing around with roller bearing one by printing the actual part number on it.

This is a tool that fits on the bull gear of a Craftsman/Atlas lathe to assist with removal of the chuck. I measured and modeled this to fit my Craftsman/Atlas 12" lathe. It may fit other Atlas lathes. I've included the stl file of what I...

This is a tool that fits on the bull gear of a Craftsman/Atlas lathe to assist with removal of the chuck. I measured and modeled this to fit my Craftsman/Atlas 12" lathe. It may fit other Atlas lathes. I've included the stl file of what I printed. I...

I designed this tachometer screen mount to attach a hall effect tachometer to an Atlas lathe in place of the factory switch location. I feel like most of us retrofit something like a drum switch or VFD, and this was a good spot for a tach. Here's an...

This is a gear cover for an Atlas lathe made in 1935. My old Atlas came without a cover for the gears. Looking on the internet, I found pictures of covers, and I even bought one on Ebay -- only to find it was too small, presumably made for a...

All parts are reverse engineered directly from an Atlas Mk.2 Lathe, Accuracy is questionable due to draft angles. ...Most of the cross slide and compound slide details are modeled.

My traverse gear case broke on my old Atlas 10 inch lathe. I could not find a good blueprint for one so I reverse engineered the one I have. I could buy a new part but they are known for breaking, so this design should be stronger. I plan on making...

Tumbler gears and change gears for the Atlas 10" lathe. All gears were designed with a 20 degree pitch angle. The 60 tooth gear was redesigned 9/26/13. I had the wrong pitch diameter for the old one, if you downloaded the older version please replace...

This is the main drive pulley for the craftsman/atlas 1/2 drive motor shaft. ...exact replica

Needed wiper covers for the lathe I was rebuilding and drew these in Sketchup. Sketchup file along with the stl provided. ...

No modifications to the lathe are required and the only fastener used is a 3.5" 1/4 20 bolt with a nylock nut. You may need to drill out the hole where the bolt goes, and don't be afraid to sand it to fit your carriage. Prints well with no support on...

Follow the directions from the original. ... I modified to fit my 10F TH54 Atlas lathe. Also made part to use as the indicator. ... Not sure on what other models this may fit.

Acme cross feed nut for Atlas/Craftsman 6" lathes.

... dial. I had put a hole in it for a setscrew, but it's such a snug fit on my lathe I didn't bother with the screw. This may fit other Atlas/Craftsman 618 Lathes but was designed for this one - http://www.lathes.co.uk/atlas6inch/page2.html. ...

This is a replacement handwheel for and old (1935) Craftsman / Atlas lathe. ... I include a knurling library that was made by someone else.

... have been Remodeled and a new version uploaded. ...Half Nuts for my Atlas QC54 Lathe. 2 separate Files the first one has the relief to prevent band sawing, the second is the original I printed and tested in video. ...The second file prevents support

This is a replacement cover for an old (1935) Craftsman / Atlas lathe. It attaches to the cross-slide to cover and protect the threads. EDIT: 12/27/18 Modified .scad file such that cover size is output to console log during rendering. ...

This is my Atlas metal lathe change gear rack. The intent was to have a place for all the parts that are removable so none get lost. I printed with 5% infill. It seems study enough. This is my second Fusion 360 project, so I'm sure there is a...

Atlas/Craftsman 12" lathe parts. My one piece saddle has 10d-9 cast in the bottom of it, and is really hard to find. I have 2 of these lathes, one went through a building fire so I'll add additional parts as I discover what else I need to complete...

This is a stand for Atlas Lathe change gears (https://www.thingiverse.com/thing:143893) EDIT: 1/14/19 -- added STL files for nuts. NOTE: the gear_stand.scad file is to be used with OpenSCAD. In that file, at the top, are a series of variable...

To mount the Clough42 ELS on the rear of the lathe, I needed a little more thread on the lead screw and decided to replace the lead screw support with a slightly shorter version. Additionally I used two thrust bearings to react the preload. I didn't...