atlas 618 lathe 3d models
9767 3d models found related to atlas 618 lathe.thingiverse
No modifications to the lathe are required and the only fastener used is a 3.5" 1/4 20 bolt with a nylock nut. You may need to drill out the hole where the bolt goes, and don't be afraid to sand it to fit your carriage. Prints well with no support on...
grabcad
Something I've been working on. The gear tray just fits flat in a Fortus 400 if it's positioned diagonally. That's why the corners are chamfered. The drawers are from Harbor Freight. ... It was about 2" too tall so I cut off the upper and lower return...
thingiverse
... dial. I had put a hole in it for a setscrew, but it's such a snug fit on my lathe I didn't bother with the screw. This may fit other Atlas/Craftsman 618 Lathes but was designed for this one - http://www.lathes.co.uk/atlas6inch/page2.html. ...
thingiverse
Spindle thread protector for Atlas 618 (or Craftsman 101) 1"-10 spindle. ...May need to be printed slightly oversized to thread easily onto spindle.
grabcad
64 Tooth change gear for an Atlas 618 or Craftsman 6" metal lathe.
thingiverse
This is a thread protector for my vintage Atlas/Craftsman 618/101.7301 Metal Lathe. This version fits a 1" by 8tpi threaded spindle. Inspired by MrPete222. This is my first completed design and project using Fusion 360. ...
grabcad
618/Craftsmen 6 inch Steady Rest_ Modeled from an old Popular Mechanics Magazine.
grabcad
This is a model of an Atlas Mk.2 Lathe Bed reverse engineered to within a few thousandths accuracy give take for draft angles. ...Dimensions are accurate enough for most Home Shop Machinist purposes.
thingiverse
I designed and Printed this wrench to be used on my QC42 Atlas Lathe for locking the saddle and cross slide. This Wrench will probably work with other Lathes with bolts with a square head. The bolt size is .380 across. I used ASA filament because it...
thingiverse
Atlas lathes use a circular dovetail mounting system for attachments to the cross slide, such as the compound and milling attachments. There's a couple of pins that bear against the circular mount to lock it in place that tend to fall out when the...
cults3d
https://youtu.be/NF554Jrok_w https://youtu.be/1LXigsea9dg Note that these dials will not fit all models of Atlas lathe. Please look at the dial measurements to ensure it will fit your lathe. This dial will not fit the older series atlas with 1/2"...
thingiverse
https://youtu.be/NF554Jrok_w https://youtu.be/1LXigsea9dg Note that these dials will not fit all models of Atlas lathe. Please look at the dial measurements to ensure it will fit your lathe. This dial will not fit the older series atlas with 1/2"...
grabcad
Atlas 10" Lathe handed down guess 40s vintage. Model made on FreeCAD Step files transferred to OnShape to create Step assemblies and pdfs Almost all fasteners not included and taped hole not taped. Only the dials on the Compound and Cross slide...
thingiverse
This is a tool that fits on the bull gear of a Craftsman/Atlas lathe to assist with removal of the chuck. I measured and modeled this to fit my Craftsman/Atlas 12" lathe. It may fit other Atlas lathes. I've included the stl file of what I...
prusaprinters
This is a tool that fits on the bull gear of a Craftsman/Atlas lathe to assist with removal of the chuck. I measured and modeled this to fit my Craftsman/Atlas 12" lathe. It may fit other Atlas lathes. I've included the stl file of what I printed. I...
thingiverse
I designed this tachometer screen mount to attach a hall effect tachometer to an Atlas lathe in place of the factory switch location. I feel like most of us retrofit something like a drum switch or VFD, and this was a good spot for a tach. Here's an...
thingiverse
This is a gear cover for an Atlas lathe made in 1935. My old Atlas came without a cover for the gears. Looking on the internet, I found pictures of covers, and I even bought one on Ebay -- only to find it was too small, presumably made for a...
thingiverse
Tumbler gears and change gears for the Atlas 10" lathe. All gears were designed with a 20 degree pitch angle. The 60 tooth gear was redesigned 9/26/13. I had the wrong pitch diameter for the old one, if you downloaded the older version please replace...
grabcad
All parts are reverse engineered directly from an Atlas Mk.2 Lathe, Accuracy is questionable due to draft angles. ...Most of the cross slide and compound slide details are modeled.
grabcad
My traverse gear case broke on my old Atlas 10 inch lathe. I could not find a good blueprint for one so I reverse engineered the one I have. I could buy a new part but they are known for breaking, so this design should be stronger. I plan on making...
thingiverse
This is the main drive pulley for the craftsman/atlas 1/2 drive motor shaft. ...exact replica
thingiverse
Atlas 10F gears, 9-48a, 9-48b & 9-190 for reverse gear assembly Yet to be printed and tested! ... Now printed, fettled & installed, all working well
thingiverse
Needed wiper covers for the lathe I was rebuilding and drew these in Sketchup. Sketchup file along with the stl provided. ...
thingiverse
Acme cross feed nut for Atlas/Craftsman 6" lathes.
thingiverse
Follow the directions from the original. ... I modified to fit my 10F TH54 Atlas lathe. Also made part to use as the indicator. ... Not sure on what other models this may fit.
thingiverse
This is a replacement handwheel for and old (1935) Craftsman / Atlas lathe. ... I include a knurling library that was made by someone else.
thingiverse
This is a replacement cover for an old (1935) Craftsman / Atlas lathe. It attaches to the cross-slide to cover and protect the threads. EDIT: 12/27/18 Modified .scad file such that cover size is output to console log during rendering. ...
thingiverse
... have been Remodeled and a new version uploaded. ...Half Nuts for my Atlas QC54 Lathe. 2 separate Files the first one has the relief to prevent band sawing, the second is the original I printed and tested in video. ...The second file prevents support
thingiverse
This is my Atlas metal lathe change gear rack. The intent was to have a place for all the parts that are removable so none get lost. I printed with 5% infill. It seems study enough. This is my second Fusion 360 project, so I'm sure there is a...