building 3d model

However another person created this and the subsequent prusaslicer ini file. however I am not quite knowledgeable enough with gcode and prusaslicer to make the necessary adjustments to it to make it work on the mini (plus I prefer to do it directly...

Again tilt the drawing slightly, noting that you have the right corner vs the model orientation. It can get a little confusing. Save the Sketch 4. The spacer should automatically be tapered to match the corner height because the angled plane adjusts...

Each time I found that the support material came away beautifully… right up until I printed the final model. A tiny piece of the design broke off with the support (see pictures). Thankfully It's not an essential part. It's only there to keep the...

See the link below for a model that looks like the one I have. If I didn't have the laser boresighter, I would have chosen a cheap laser pointer in the $5 range or a cheaper boresighter in the $15 range. Perhaps I would have simply purchased a...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_pattern_element_overlap = 0 custom_back_extra_port_corner_radius = 5 printer_tolerance = 0.4 stencil_pattern_element_radius = 6...

&nbsp;After getting the other nosecone to work I found out that the original Sprint used a BNC-50X and I had modeled off the BNC-50Y. &nbsp;So for ‘authenticity sake’ I've added a BNC-50X version of both the stock and Astrocam nosecones.</p><figure...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_left_port_corner_radius = 5 pattern_element_overlap = 0 custom_top_port_x_position = -10 custom_bottom_outer_edge_chamfer_radius = .6...

Don't use it for rendering or model generation. (see Reducer picture) PRINTING NOTE Print at 100% infill. Try and print standing vertically, if possible so that scaffolding may be omitted on the inside. These connectors are specifically designed...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_corner_resolution = 8 custom_back_extra_port_y_position = 30 custom_top_port_corner_resolution = 8...

- Replaced PZ20 circuit's LDO with a simpler model with higher input voltage range - Added second LDO for dedicated supply to LED's - Isolated TH1 from ground plane to address vdroop effecting thermal readings - Added grounding vias for edges and...

Yes, there's an actual tank model underneath all the nonsense; it's just badly covered over since I built a spacefuture tank around it. I used a different source for my sponson lascannon; the sponson mount is from Seb's Sicaran proxy, so any of its...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_mirror = 0 stencil_drawing =...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 stencil_drawing =...

It is opened by twisting the handles on the doors in a clockwise direction.This was originally uploaded to Thingiverse in 2017, and I have now moved it here as well.I have 14 other Iris boxes designs and I have an instructable describing them and how...

After sanding the putty flat, paint it using model paint or cover it with a large sticker to conceal any imperfections. Test fit the Laforge diversity module into the hole where the old receiver used to be. Cut off this standoff because it's...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 stencil_drawing =...

Now, everything will just fit without removing the box insert.ModelQtyDescriptionquacks-chip-box.stl2Boxes for Red, Green, Blue, and Yellow ingredientsquacks-chip-lid.stl2Lids for those boxesquacks-misc-box.stl1Box for the miscellaneous ingredients...

At each joint- extend the cable to it's most strained position and then firmly secure it to the next joint in the chain with a zip tie.&nbsp;Example Setup:Though I tested all of my parts and you can assemble in any configuration you like, if you want...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_port_x_position = 20 custom_back_camera_corner_resolution = 8 custom_bottom_fillet_resolution = 8 stencil_horizontal_position = 50...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 stencil_drawing =...

If you're using another fan make and model, make sure you check the polarity so it isn't reversed. If you don't have crimping tool you can just cut off the connector from the original fan and solder/splice it on. Print the 3 (4) parts. If you use...

I have left the original design files as well to preserve version control.&nbsp;Design File Included: .f3d, .ipt, step, .skp, and .obj files.&nbsp;Follow The Makers Workbench...

...More importantly, Thingiverse hasn't run their customizer queue since Jul 10, 2020 so until they fix that issue, you will have to install and run OpenSCAD (free software) on your own computer to process the code to create your own customized models.

The code you want to stop at is M107Example of first portion [to copy and paste in a new document]:; generated by PrusaSlicer 2.4.2+win64 on 2022-05-19 at 22:12:52 UTC; ; external perimeters extrusion width = 0.45mm; perimeters extrusion width =...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_corner_resolution = 8 stencil_horizontal_position = 50 custom_back_camera_x_position = 0 custom_top_port_corner_resolution = 8...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_pattern_element_overlap = 16 custom_back_extra_port_corner_radius = 5 printer_tolerance = 0.4 stencil_pattern_element_radius = 8...

The model can accommodate slightly larger and smaller sizes as is. To fit your doorknob you may either scale the STL file before printing (measure your doorknob diameter D and scale by D/54), or adjust the parameters in OpenSCAD, render (F6), save...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_size = 20 custom_bottom_port_x_position = 20 custom_bottom_port_corner_resolution = 8 stencil_rotation = 0...

Customized QR code and tag design from Thingiverse's model (http://www.thingiverse.com/thing:46884) using Customizer Options: - qr_rotate: 0 - corner_num: 0 - corner_radius: 10 - qr_scale: 1.6 - qr_size: 29 - qr_y: 0 - qr_x: 0 - tag_height: 50 -...