chris craft 3d model

i may add a second hole for wiring so it doesn't have to be drilled by others but right now thats how i got the led to the inside under the boot an up through the hole i drilled, put the body on first b4 trying to run the wires or they will try to...

&nbsp;After getting the other nosecone to work I found out that the original Sprint used a BNC-50X and I had modeled off the BNC-50Y. &nbsp;So for ‘authenticity sake’ I've added a BNC-50X version of both the stock and Astrocam nosecones.</p><figure...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_mirror = 0 stencil_drawing =...

After sanding the putty flat, paint it using model paint or cover it with a large sticker to conceal any imperfections. Test fit the Laforge diversity module into the hole where the old receiver used to be. Cut off this standoff because it's...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_corner_resolution = 8 stencil_horizontal_position = 50 custom_top_port_corner_resolution = 8 custom_back_camera_x_position = 0...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

Also download the original 'COMPLETE.BLEND' from Jumpman971's Thingiverse so you can see the model in Blender. (Also get Blender.) (I'm pushing this out before a throat piece is remodeled because I have a 2-week vacation coming up and I'm busy this...

idk what slicer or print settings were used on the original print, but I had to redo the entire geometry of that area to get it to print right without disturbing the bevel of the rest of that model. Unfortunately, given I don't have the original...

Except for the Sunlu mount plate just lay the models flat. The Sunlu mount plate I printed standing upright - even without support (although some minor bridging is needed, but that was no problem)</p><p>As mentioned above, the hygrometers are...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_mouse_ears = 0 pattern_line_thickness = 20 custom_bottom_port_corner_radius = 5 custom_back_camera_corner_resolution = 8...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_case_wall_thickness = 1.6 custom_back_camera_corner_resolution = 8 custom_left_port_corner_resolution = 8 custom_corner_resolution = 8...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_shape = 6 custom_bottom_port_corner_radius = 5 custom_back_camera_y_size = 20 printer_tolerance = 0.4 stencil_pattern_line_thickness = 30...

My original plan was to also model a strap clip for the bottom of the mount, but I found that it was unnecessary, as the entire thing can be attached directly to the head strap and head pad with a velcro strap. I used a couple of long velcro cable...

Tonight, I finally decided to model the hinges in fusion and print out new ones. The test seems to work well enough. So I'm printing them with a roll of ProtoPasta Carbon FIber HTLPA. This will be my first real test of this filament. I will update...

Keep doing it until you get a reliable contact. Multi-color printing For printing in multiple colors, you need to slice the model and save it as normal gcode. Then, you have to insert the M600 command. You can do this manually by opening the gcode,...

I always use a 4-5mm brim around such big models. You may need to turn off the skirt line then.</p><p>The 8 holders inside were printed with 100% infill, just to be sure that they were stable enough. You will need some screws, washers and nuts as...

The casing has a channel modeled in the side to accommodate the ribbon cable coming out from the Raspberry Pi. 3) Insert the smaller end of the ribbon cable into the Raspberry Pi Camera Module, then place the module into the view port. The view port...

This stage can be handled in several ways: 1: The instructor can have several models pre-made for demonstration and discussion. 2: The instructor can have kits of parts put together for students to work with and attempt to build their own trusses. 3:...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_case_wall_thickness = 1.6 custom_back_camera_corner_resolution = 8 custom_left_port_corner_resolution = 8 custom_corner_resolution = 8...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

This print allows to elegantly mount your Bosch eBike Charger to the wall, out of the way, right where you need it. I made this version because several people indicated that they liked my eBike Charging Station but preferred a standalone version of...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_phone_thickness = 10 custom_back_extra_port_corner_resolution = 8 custom_bottom_fillet_radius = 1.6 custom_left_port_corner_resolution = 8...

### Bridge style cards (58mm x 88mm) * `codeandmake.com_Quick_Draw_Card_Dispenser_v1.0_58x88_Single_Open.stl` * `codeandmake.com_Quick_Draw_Card_Dispenser_v1.0_58x88_Single_Covered.stl` *...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

The firmware numbers will match regardless of your printer model. If you use a slicer that requires EEPROM, make sure to update your EEPROM settings to match your new firmware. The easiest part is printing the adapter plate - any ABS or PLA preset...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

... satellite. The team’s website is http://csdc.uvic.ca/ Note that I did not create the Diamagnetic Payload Assembly, this was created by A.G.O. Environmental Electronics Ltd. The magnetorquers are not in the model, as they are still in development.

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_fillet_radius = 1.6 custom_top_port_x_position = -10 use_mouse_ears = 0 custom_bottom_port_x_position = 20...

Use "leveling_test.stl" model to test auto-level accuracy. I made some work tests of this firmware but there still could be bugs there, so use it on your own risk. Enjoy! :) Update 1: My Start and End G-codes in Cura working well with this...

-Number of facets causes extreme delay in saving/rendering model, likely due to me not understanding the correct scad approach; I am still learning, feel free to leave me any feedback so I can improve my techniques. -Flat ring design (just like the...