christmas tree stl file 3d models

If there is enough interest I'm happy to create new files for newer printers, but someone will have to send me the dimensions for the spacer.Note: This design is seriously back heavy with the heater and control board mounted.  It will lean back...

Use filler putty to fill in all gaps between printed pieces and file or sand flush. 6. Paint with filler primer and hand sand all pieces with progressively finer sand paper except Grip 1, Grip 3, and Pommel 2. Repeat this step until desired...

The AND has one plate (c) and the OR and XOR have two (c and d).Post-PrintingSome filing can be needed to get the internal plates to fit in the fixed plate (gray).For the OR and XOR gate, the two floating plates are the same but one must be flipped...

This is installed 30mm below the top of the vertical frame, or any distance you prefer The Z axis and bed are then moved so they are around 42-43mm below the X & Y axis Print one of each part, in the orientation you find them, no supports are...

I've shared the SLDPRT &amp; SLDDRW files for your reference. The drawings have been updated since I last machined the parts.</p> <p>You may need a rear (read: longer) QR skewer since the effective clamping width is going to be much longer.</p>...

The files for the bearing hinge are "Bearing Hinge Interior" and "Bearing Hinge Exterior". The bearings are clamped in place with a couple of M8 35mm bolts, with captive nuts in the Interior portion. There's 1mm clearance between the two sections, so...

You don't need to disconnect any cables from your Einsy case! You will need: two m3 12mm screws (m3 10mm will work ok) two m3 hex nuts Also check out my side mounted MK3 LCD mod https://www.thingiverse.com/thing:3483560 Now you can mount a Logitech...

I have included my FreeCAD files and tried to clean them up, however I cannot make any guarantee that my organization or ways of making the parts will make sense. I was learning of multitude of different ways of doing stuff. ...If you have any questions...

This is a remix of the file "Chassis_2_V1" for Staind's RC Tank.\r\n\r\nI wanted to add some headlights and I found a cool looking USB bike light for about 6 Euro on Ebay. It is somewhat oversized, but I like this asymmetrical "hull mounted laser...

Uploaded all CAD files for the parts (SW 2014). Print Settings Printer Brand: MakerBot Printer: MakerBot Replicator 2 Rafts: Yes Supports: Yes Resolution: 0.15 Infill: 5 Notes: STLs oriented for printing; the gauntlet looks like it could print...

Update:19\06\20 Uploaded Step File. Jan 2020: It may be worth checking out my latest design - Hydra Fan Duct &amp; Tool Change System which IMHO is far better in a lot of ways than this Hero Me remix. Link: <a...

Some nut holes are closed with 0.2mm thick extrude to improve print quality, use a small drill or a file to open them after printing. The shifter paddle in real-world pictures is different from the one that is available for download. Update 1: Added...

Sorry for the confusion with both metric and standard parts, it's what I had laying around.&nbsp;&nbsp;BUILDStart with a test print of the crankshaft and verify interference fit with the bearing.Some minor sanding/filing will help the finger engine...

I've attached my PrusaSlicer.3mf files in case anyone wants them for reference. I initially made each design only a single layer, but you could see the color of the rest of the lid through any first-layer imperfections. Although it required more...

I highly recommend measuring your display and seeing how close the values are to those at the top of the SCAD file, regenerating as necessary, and if all else fails breaking out the X-acto knife and sandpaper and going to town. You can follow this...

M0UKD design is published at: https://m0ukd.com/homebrew/antennas/144mhz-2m-portable-yagi-vhf-beam-antenna/ Updates ---------------- * Updated the 3mf file for the driven element box and parts. Support enforcers were not working on one of the clips....

- tiny 9v fan (25.5x10mm) https://www.ebay.com/itm/304165517410?var=603274137473 - magnetic stirrer rod to put inside the bottle (I'm using type A10 in the video, but I think B20 is a better fit for these bottles and this job) -...

Updates ----------------------- 12/10/2020: the file I added today is a total overhaul of the air assist with a few new features. NOTE: this is not backwards compatable with the other pieces. it no longer has the need for any gaskets, the air is...

Filing may be required for these interfaces: OD of carrier & ID of brifter mount. Clearance is 0.5 mm right now small OD of brifter mount & ID of brifter ferrule port brifter mount length that inserts into the brifter (could be too long) the...

rnrnThe properties for these files can be explored in solidworks or other professional CAD program. Preparation Students should understand basic geometry.rnStudents should understand force, loading, and dynamic forces.rnStudents should understand how...

[there was an oops in the "Duct" file, a bump should've been a hole..... fixed on 3/21/2019 https://www.amazon.com/gp/product/B01KHMFH1M/ref=ppx_yo_dt_b_asin_title_o05_s00?ie=UTF8&psc=1 Print Settings Printer: FT-5 Rafts: No Supports: No Resolution:...

I built this with spare parts to make artwork and crafts, mark fabric, etch PCBs and to practice my modeling skills before I start my CNC router project. Example engravings: https://www.instagram.com/p/B_o2uqJDyem/...

Will be uploading source files. ---------------------------------------------------------------------------------------------------------------- Este es el resultado de un viaje realmente largo con el MMU2S, que en realidad comenzó en la misma...

But the post is touching the sides, so altogether we have 0.6 mm to account for (9.6 mm - 9 mm) that is not in the design file.Now consider a cross-section, after splitting the print in half from the top. HE is relevant on both the "left" and "right"...

This is 100% possible since I've included the 123D Design file. But it's on your own risk. SOFTWARE Retropie is the main operating system, and you select game system and game through Emulationstation. Retropie is a great operating system, so go and...

There is a through-hole for the display and button cable.I also had to print a stand that is screwed onto the load sensor to get a smaller contact area due to the slight angle of the adapter.Included is a schematic on how everything is connected as...

If someone really needs it; i'll resize the holder for an alternate version...but either way a drop of hot glue is in order to make sure its secure. Hand-wiring was a little nutty, since you have to mentally reverse some of the layout going by the...

I've included all the files, not just the updated ones. The update falls into three categories: To provide a larger operating window. The original design worked, but too much less that 100% of the time to be fully satisfactory. The major factors...

==================================================================== Let me know how you get on printing this and other items I produced as I am unable to test print any of my files right now (having a baby in the room means I have to avoid the...

That assembly is shown in some of the photos above, though the files here are only of the carriage and BLTouch mount parts. For the cooling system, also download one of the cooling designs mentioned here, or use the basic E3D V6 fan holder for the...