circle floaties 3d models

Customize the look by using different colors for the parts.The PoleCatch a ball and vault it to the next track.Assemble pole- + pole-base + lock-Customize the look by using different colors for the parts.The Whirlpool!The ball goes in circles until...

Create a center point circle from the end of the construction line for the eye. Mirror the mouth, eye, and triangles to make it all symmetrical.  EDITS:Take the mouth outlines from the bottom center point of the arc and the outermost...

There is a wide circle part on top that I removed, then sanded down the edge to make it flat and I made it 16mm's wide. I also had to shave the sides slightly where the screw passes by. I placed a 30mm fan in the back that is blowing air in to a...

Before that I drew the circle with the help of the inner back (!) of a lamp tube. ---- Step 2 - Inserting Twin-wall Sheet "glasses" For this step you need: • Lamp DuoLux_tuberight.stl • Lamp DuoLux_tubeleft.stl • Lamp...

However, after drilling one pedal with this template, and the other pedal using an installed adapter,  I found that the adapter is easier and more secure to use as the template for drilling precise holes.  Printing:Print two adapters, one for each...

... second image posted here is a scaled-down stitch result. The MD lens used does vignette, but surprisingly little considering it was designed for a 43mm diameter coverage circle and the stitched captures have a 60mm diagonal. 

The felt is a white circle sitting under the plunger. 3. Solder 1 diode across the coil post solder points on each coil with the silver line (cathode) of the diode facing what you will use as the positive (+) connection point. You can choose...

A new positive wire should pass through the other half of the circle. Solder both positive wires to the positve terminal on the LED strip, connect its ground wire. Pass the positive and the two ground wires through the connector at the bottom of ring...

(I just use the casing as a lens cap for storage and transport)In the US Amscope sells an objective which is identical in outward appearance (but I haven't tested it):https://amscope.com/products/pa4xk-v300I've included two adapter designs:The crop...

So that is where the heat will come from. The stock fan blows air into this heat sink in the shape of a circle. Meaning most of the air hits the outsides of the fins that are not that hot to begin with and then the air escapes out the sides. The...

There was a [model on Thingiverse](https://www.thingiverse.com/thing:3536767), but it had a very low resolution STL (circles had 16 sides, for example), and it was originally designed for a 1:1 model. I found a couple of great models on GradCAD from...

Before that I drew the circle with the help of the inner back (!) of a lamp tube. Step 2 - Inserting Twin-wall Sheet "glasses For this step you need: Lamp DuoLux_tuberight.stl Lamp DuoLux_tubeleft.stl Lamp DuoLux_glassfixingring.stl (2x) I started...

shorter belt: cut 270mm (!!!) of the belt means less vibrations and more stabilitysmaller leverage/distance between pulleys on the left and right carriages: old distance was 50mm; new distance - 36mm -> means more round circles, less chances for...

In his folly, Thirazar attempted to recreate the device, though it ended shortly after it began as the device backfired, creating a permafrost over Thirazar, freezing him for hundreds of years and unleashing a small circle of permafrost on the region...

Take what's theirs and make it your own! ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~More fun stuff:Construction:Building under construction Part 1...

If you want to align knob to various angles, you can use different knob inserts.Knob Cover with Triangle Pointer (3) - Seam position: RandomKnob Cover with Circle Pointer (2) - Seam position: RandomTriangle Pointer Insert (3)Circle Pointer Insert...

Avoid lifting and warped prints!There is a small amount of support needed - "for support enforcers only."Under the elevator shaft on the Middle Floor and Top Floor.The elevator door on the base floor.Increase the size of your “Dice Tower - Building...

At the very least this will require a wet cleaning of your camera sensor, and in the worst case this will render your camera into scrap. Take care.Shooting with the tubeTo mount a lens to the tube, align the Canon lens' alignment mark with one of the...

Here's what this looks like as Python: ``` from numpy import * from minkowski.operators.union import * reference_point_A = (20,0) # define stencil size to determine grid scale stencil_size= 40 scale = stenilstizex/ 80 scale1=scaletsinly # 160 /...

Take what's theirs and make it your own! ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~More fun stuff:Construction:Building under construction Part 1...

Take what's theirs and make it your own! ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~More fun stuff:Construction:Building under construction Part 1...

At the very least this will require a wet cleaning of your camera sensor, and in the worst case this will render your camera into scrap. Take care.Shooting with the tubeTo mount a lens to the tube, align the Canon lens' alignment mark with one of the...

Take what's theirs and make it your own! ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~More fun stuff:Construction:Building under construction Part 1...

Place the blank model so there is 0mm offset in the X axis and -6.96mm offset in the Y axis.At this point you could use the blank as is and it is centered as if it was a full 100mm circle. If you use a large silhouette, or you create a collage, the...

Just refile it a bit with a cutter!Update 31/01/24I started the electronic part with some late.The main issue is my board (NodeMCU esp32 or esp8266 d1mini)Both have some high deep sleep current, almost 20mAh, so running it on battery is pretty...

they are a full inch thick which is pretty nice, and you don't even have to cut the circles which is even better. Obviously you can do whatever you want here and could even go smaller if you want, but the 18" is about right. As you can see, I chopped...

Check the orientation, the small cutout is in the back (yellow circle, see picture).Insert an M3x10mm screw and loosely tighten it. Repeat this step for the remaining holes.</p><p><i><strong>NOTE:</strong></i> The screws should be loosely tightened,...

Also I strongly recommend to use a brim so that 8 circles connectors won’t fall during printing.The connector need at least 4 small support, please take the 3mf file of the connector, the supports are already pre-charged.All Advanced Plates needs...

and a set of circles. "Whats in a name..." can be another clue.Enjoy!08.02.24 - I've added some new bits like the Arc of Convenience, and updated Do Not Disturb door handle attachment as well as a Handy ping-pong table clip on for fun - paddle...

- A desktop nameplate, sweeping around in a circle. Customize it to show your name or text (Press "Open in Customizer" above or install [OpenSCAD](http://www.openscad.org/) on your own computer and see the instructions below regarding OpenSCAD). ...