diy 3d printed rc plane

Hobby Tool Holders This is an initial set of compact hobby tool holders the purpose of which are: Short term tool storage for tools being used on an active project Organization to help keep the bench cleaner To help facilitate rapid tool acquisition...

I'll update this when my print finishes. The Fly can fly from any position to land on any bug that that your opponent placed, moved or flipped on their last turn. This includes bugs on top of a stack. It then moves one space down into an empty...

Later I will add photos of a finished print with some painting and post-processing tips.See the Remixes section for two other variants.-------------------------------------------------Tento bunkr, tzv. <strong>řopík</strong> (podle ŘOP: Ředitelství...

Fishing the wires through the print is a little tricky but not difficult. Longer screw is for the battery latch and sandwiches all parts of the adapter together for strength. I used flat head socket screws since I had them, but any flat head M3...

New short blades printed in one part, much stronger for the same flight. * Fit in Prusa MK3S (210x200) * New 2 parts screwed cabin. If you don't have screws, you can glue the two parts. Update 22-03-20: New bimotor version The advantages of a...

Everything is designed to print without supports.&nbsp;This project is a work in progress, but current state is usable.Spool Assembly:Attach tie to desired slot. I have found the slot opposite to the hanging hooks tend to position the cord ends in a...

I wanted it to be a very secure fit, strong, lightweight, low-profile, inexpensive, easy to print, and to also not damage the surface of the fork. I managed to achieve those goals.&nbsp;</p><p>I got the idea for this project from k-Lite's design,...

Before starting, assemble the cylinder by sealing it (there are holes on the sides) and printing it from transparent material for better visibility. If you give up, you can disassemble the game and try again. Good luck! HINTS: This game aims to...

I aimed to keep the list of printed parts minimal by developing a two-gear system instead of a more complex scissor extension arm. A unique feature of my design is the guide wheel that supports the tracing gear to keep it level and prevents it from...

You can see the demonstration in the video: https://www.youtube.com/watch?v=g27qqC4I8kU Print the base, battery holder, and choose a foot (I used 5 degrees; haven't tried the others, but Blender Rigid Body simulation shows that higher angles give...

The front shroud includes a slider that allows the air flow to be redirected away from the printed part if required. The Triple Lower Vent attaches from the bottom using 3-M3 countersunk machine screws. Because the vent adds some height, the...

I still drilled the pivot pin hole (you can't fix it if it prints too loose, right?). Note: If you don't have an Arrma 4S car to scavenge for parts these probably aren't any use to you. I had the parts so I made these knuckles and C-hub so I...

You do not need to know any programming or write a single line code to use OpenSCAD.Once you've entered everything you need, you can export an STL file for printing. <a href="https://www.youtube.com/watch?v=cBesMfP7Ddo">Here's a helpful video that...

PLEASE CHECK YOUR PCB SIZE BEFORE PRINTING! I MEASURED MY PCB WITH A DIGITAL CALIPER AND IT MEASURED 65mm X 39mm EXACTLY Note there are many versions that look similar but have key differences. Make sure you use the one that is exactly as shown,...

This miniature comes with optional presupported files for resin printing. These files come as ready to go STL files or Lychee files if you wish to edit the supports for your custom needs. You can find my latest releases over on my Patreon!   The...

You get the following figures in both our standard 36mm scale and a smaller 32mm scale so you can choose your prefered size: - Operative Balakin weilding a flamethrower - Operative Alekseev dual weilding a flamethrower & uzi - Operative Federov...

&nbsp;The only repair is replacement of the hammer, as epoxies and glues will not hold.I printed this using Prusament PC Blend, as this hammer needs to withstand some serious punishment to actuate the gas valves without breaking. &nbsp;The PC blend...

so printed this idea first).So I love the idea of swords, and love the look of long swords, then i heard about hand and a half swords which are just long swords but longer, but not like stupidly big like double handed behemoths. This is a segmented...

Use a thread lock on the bottom 3 screws to prevent them from vibrating loose and insert them into the remaining 3 bottom holes and tighten until snug Printing I would strongly recommend a filament that is UV stable so that prolonged sun exposure...

You'll need to print three of my custom-made carriage blocks and three 10mm spacers. Don't use the blue carriage plate, as my new carriage block is integrated into it. Follow Shaunppl's instructions for installing linear rails on extrusions. His...

I was inspired by the [Bed Cable Side Chain mod by Whoppingpochard posted at prusaprinters.org.](https://www.prusaprinters.org/prints/54320-artillery-sidewinder-x1-genius-illuminated-bed-cab) The mod relocates the bed heater and temperature sensor...

... better against the wall and feels stronger. - Chamfered the screw holes so they sit flush. - Increased the depth of the holder by 1mm to provide more space for the screws. - Printed in white instead of pearl white because pearl white looked dirty.

I have printed the lid in white PLA with slight indents for added light to come through at the right places. (it allows me to see the LEDs change so that I know it is working and not hung.) The lid is a (tight) push fit that stays in place well and...

Here's a list of supplies required for building the frame: * M3 Bolts (16) 50mm, (8) 25mm, and (10) 15mm screws for electronics * A large quantity of ABS materials * Patience For electronic components, you'll need: * Any generation of APM with an...

If our accessory size is close to what you need, you may be able to scrap some of the accessory after printing to make it fit. Or if it is too large, you can use some rubber padding to take up the slack. It is always good to use rubber padding to...

When I built my dedicated printing room, I failed to notice that the switch for the overhead lights was located at the top of the rear wall, which is not very convenient. This design has 4 main parts: The Switch Plate mechanism, The Corner "Pulley",...

Estoy seguro de que si se pusieran las pilas podrían volver a crecer mucho.-AUTO TRANSLATE TO ENGLISH-After 3 years of using my mobile charger (huawei P30 PRO) the connector had started to break slightly (surely my cat biting it and dragging on the...

I also made some minor tweaks to make the counters look better for 2 color printing. Use layer height of 0.2mm and set your second color to start at the 14th layer. Update 4/22/2019 -- Treasure, Brick, Exert, and Embalm tokens released! Treasure...

# Print Instructions: Be sure to use supports for the wall pin and the gun holder. Take care to clean the supports and leave a smooth finish on the gun holder. I set this up so the gun points to the right to hide the screw holes. If you want to...

4.) Time to choose colors for printing. Going all lime green, it looked nice because I thought this vibrant tone brought a certain brightness when laid on a dark or otherwise subdued backdrop which always helps capture attention wherever applied...