drone pre flight checklist 3d models

Elevator trim switch for a flight simulator. Based off Cygnet / S-Tec style switch shown below: https://www.aircraftspruce.com/catalog/elpages/trimswitch11-15410.php Utilizes #4-40 set screws. I sized the holes in the base and toggles...

Additionally, I added other switches I usually use during the inflight phase to avoid moving around in the cockpit in critical flight phases like taxi, take-off & climb and approach & landing. ... See attached pdf document for material list and...

I'm embarking on a revolutionary project that will electrify enthusiasts and provide an unparalleled experience by crafting a series of open-source flight boxes and modular accessories that can be tailored to any flying preference. ... To gain insight...

Hi This is Gorilla Jet Flight Ares - Last Enemy of Mankind Evolved from Higher Ancestral Beings, Equipped with Powerful Arms and Agile Jumping Abilities The Twin-Turbo Propeller on the Jet Wing Enables Stealth Mode, Rendering Enemies Undetected...

... is a bit too flimsy for serious use. I ended up using my Thrustmaster racing pedals for rudder in flight sims, so I am not sure if I will work on this in the near future. ... Video about the whole setup: https://www.youtube.com/watch?v=na3NeZJYK3g

Human flight mouse Batman, before printing, in the slicer, increase the model at your discretion to the size you need. https://t.me/AlexStormND https://www.patreon.com/AlexStormND https://cults3d.com/en/users/AlexStormND ...

This is a scale model of an american crow in flight. The wingspan is approximately 3ft and is cut into sections that will fit on an ender 3. I don't recommend scaling this down past 1/2 or so as some parts may become too thin. The eye sockets...

NEW VERSION: https://cults3d.com/en/3d-model/various/stinger-v2-rubber-band-launched-free-flight-glider This is a 3D printable toy glider that can be launched by hand or more reliably with a 3D printed rubber band shooter. The plane should be...

this an additional piece for the "turtle beach velocity one" throttle quadrant a flap lever for airliners/general use in flight sim (Other layouts may be available in future) --size and colour-- colour doesn't matter but will match with the rest of...

Here is the model I built for my dad as he requested, so here's the ship that will take us on Flight to Mars. In reality, it was essentially what they would have used in 'Destination: Moon' but they wanted something with a V-2 look. With this model...

A straightforward 30mm flight controller mount that I use to securely attach gyro components to frames lacking the standard 30mm mounting holes. To ensure a precise fit, I've updated the design to correct the centre-to-centre length from 30mm to the...

This is a spiral bird flight diverter, used to avoid birds crashing againts main powerlines. The spiral is about 30cm tall, 80mm diameter on the thick part. This desing is originaly minded for a 15.8mm cable, so it's about 16mm inner diameter on...

... on my creations. I'd love to view people's interpretations of the flight stands, especially with pictures of them being used during games. ...It brings me immense joy to think that individuals are utilizing something I designed in their home games!

Softmount designed specifically for quadcopters' flight controllers features a 3mm hole to securely attach it to the frame screw. The plug fits perfectly into the fc's 3mm holes and locks firmly in place. The distance between the upper and lower...

This MakerTron is built for flight and exploration, with the ability to navigate challenging terrain due to its robust tracks. It was printed at a moderate speed using a standard 15% infill and a raft. To ensure easy assembly, I divided the parts so...

The flight stick alone works great for Warplanes: WWI, but the throttle is not as useful because you have to use your flare gun and drop bombs. I think the throttle will work better in Warplanes: Battles over Pacific. The parts are connected by...

The flight stick alone works great for Warplanes: WWI, but the throttle is not as useful because you have to use your flare gun and drop bombs. I think the throttle will work better in Warplanes: Battles over Pacific. The parts are connected...

... mark on my mind. I ponder: the stark contrast between Icarus's majestic flight towards the sun, his unbridled momentum towards the sky, and his eventual downfall, serves as a poignant reminder of the human desire for freedom and self-determination."

F-15 inspired flight throttle, has been a lot of fun to design and build. Base can lack weight so design is intended to be attached to a mount. Some parts: 2 x 8mm panel mount button 1 x 6.35mm panel mount double throw switch 1 x tdc mini...

Printed hatch for the Dragon Flight 95 RC yacht. Simply drop into the hatch opening and secure with hatch tape, making it a breeze compared to patches. Equipped with a convenient loop that allows you to tie it directly to the servo tray on the boat,...

Case for F4BY v2.1.5 flight controller still usable despite lingering issue with disposable covers for connectors. Disposable covers work fine when they're discarded, but there's no room to accommodate plugs inside the case with a wire harness passed...

This is a remix I made from TheTimGid remix of Akaki Flight Simulator Pedals. I added two holes that allows attaching the pedals to any wood base, adding more stability while gaming. Some tips for printing it: - Don't use raft or brim for...

Model of DJI - A3 - Flight Controller prepared for needs of Sevendof AS for development purpose due to lack of officially released of the geometry by DJI.Released with employer permission under Apache 2.0 License.The model includes the DJI Logo and...

This solution addresses the issue of not being able to see switch labels on the Honeycomb Flight Yoke in low light conditions. I ordered LEDs and resistors from Amazon. Using white PLA was necessary since black filament was unavailable, but painting...

It's a compact and modular flight sim controller. This design allows easy modifications like the levers order (right or left handed). You need : -Screws 3X 6mm Countersunk Bold M6x25 6X 6mm Hexa Bold M6x30 2X 142mm threaded rod M6 4X 4mm...

I use it with FS2020 but it should also work with other flight simulators, as it is recognized in Windows (10 or 11) as a joystick type device. I wanted a robust trim wheel that fits on the Saitek throttle quadrant and also a system that preserves...

This is a model based on the "Sleepless Flight" ship from Destiny. This model is best printed with SLA, but can be printed in FDM as well. However, if the model is printed in FDM, at the current scale, most printers will be unable to handle...

The design uses: ● 1x M8 metal bar 570 mm in length (you could possibly shorten this a little more as there is some excess) ● 1x B10K Potentiometer ● 15x M3 bolts I will follow up with a desk clamp & a ways of mounting this to a flight sim...

I designed this flight controller (FC) adapter for my quadcopter build. My FC is a KK board from Hobbyking that has a 45mm hole spacing, but the frame I bought has a 30.5mm spacing for mounting the FC, probably with an FC like a Naze32 in mind, which...

More Details at BCFPV http://www.bcfpv.com/printed-flight-triple/ Here is my Tricopter frame used to film the following short http://www.bcfpv.com/shoots/ This is a super simple print that makes a very light and surprisingly strong frame which folds....