eg models

Components used: An SG90 9g servo motor: https://www.amazon.fr/AZDelivery-Digitales-Micro-Servo-Parent/dp/B081Z5V3M2 https://boutique.semageek.com/fr/104-micro-servo-tower-pro-sg90.html?search_query=sg90&results=1 a paper clip glue to assemble the...

... this design, but don't want the silly text on the knife strip? Check out the modular version! Modular Wall-Mounted Magnetic Knife Strip

- SD socket is a twin model for normal and micro SD cards, slightly bigger opening will be necessary. https://www.aliexpress.com/item/1557385706.html spm=a2g0s.9042311.0.0.94774c4dNZcdtH - Firmware is modified to handle changes, using Roger...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 custom_corner_resolution = 8 stencil_drawing =...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_corner_resolution = 8 custom_back_extra_port_y_position = 30 custom_top_port_corner_resolution = 8...

 - Click on the "Download" button and you will find the download file in small print coloured light grey below the Model  files. Using Onshape is easy - open the attached link, and double-click on the #BOTTLE_DIAMETER parameter to...

 I have it installed on both my printers and it's really nize.MK3S and (+) versions of the adapter are unique to each model and not interchangeable.Both adapters drop in over the screw heads as shown and get trapped between the extruder body and...

I have not modeled any nut traps in the parts because I think they will weaken them so all bolts here just screw into the plastic. I believe the parts are thick enough that the bolts will not loosen but time will tell._ 1. Completely disassemble...

Deck furniture is always a good way to add interest to a model. You might want to install a waterproof switch somewhere on the exterior to save having to unscrew the whole deck every time to turn it off and on. Enjoy sailing your Pocket Boat,...

The code is a bit messy (especially for the rack), but it should work for most reasonable settings. This way you can also increase the resolution of the 3D models, Due to size constraints they had to be rendered a bit low. Using this bash script you...

I used this 5/8" tall flat bellows available from McMaster Carr:https://www.mcmaster.com/1320K111/These bellows are made for this job and are resistant to oils, lubricants, and heat.The models are designed to fit an Eerie Tools SM-LTHM 7x14 lathe but...

I added some build notes below and a BOM which doesn't include screws, wires, connectors, etc., but has all major components. I planned to revisit this model and release a better version. However I have at least a year's worth of projects in...

A custom-made enclosure specifically designed for the Raspberry Pi computer assistant Assistant assistant A bespoke casing tailored to fit the Raspberry Pi device. assistant Created especially for the Raspberry Pi, this is a one-of-a-kind case. ...

Another thing to note is that there have been a few minor changes to the model since I printed the one in the pic, however I don't think anything changed will cause a problem. The STP file is included for remixing. Just wanted to mention some info...

One intersting thing I probably should have done, is just print the columns on the platforms, would have saved some time, and the hardest assembly step. Next Acquire the Electrical components: Electrical Components Post Printing is very involved,...

Test Print Video here: https://www.youtube.com/watch?v=H8vL2GeMYMQ Previous version here: https://www.thingiverse.com/thing:4650517 As per the previous version a big shout out to Scott3D for his fabulous work on the Hypercube Evo which I have taken...

Note: dimensions are in metric system (in millimeters, mm) and the model adopt A4-size paper sheets (not US-letter). <h3>Assembly instructions</h3> For the 3d printing, we used white resin for both "pointer" and "pointer+wheels". Concerning...

If you need a lot more room (more than a few mm) you may need to update the model to scale it appropriately. (~$1 of filament)</li> </ol> <ol> <li>Light string or rope. Cut it about 5ft 6 inches, or just enough to make a loop on the elbows, running...

Z gap between support interface and model is 0.2 mm For the adapter plate I used standard supports with the same support options Other parts: For convenience, I included the 40 mm fan cap, part cooling duct and BLTouch mount from the original...

Cable clamps bolt to the Extruder mount bolts to keep the cabling tidy, which I've not used yet as I can currently only run 1 of the heaters at present (my A20M control board is a V4.1 model which doesnt have the components fitted to allow for dual...

 My model has had almost no use at this point but I don't think that PLA will be a problem in use, but consider PETG if you have it.HARDWAREUnfortunately we have limited hardware supplies where I live, so there is a strange mis-mash of sizes and...

the older model this was printed from did not have the pockets for the hex nuts so it was threaded directly into the plastic instead. Ive uploaded a reinforced version of the arm that should work better with heavier controllers.i also opened up the...

The shoe lace is optional but it's a good way to secure the handle from unfolding when you don't use it.Print SettingsDon't rotate the models when placing them in your slicer. I have placed the parts in the best orientation possible with surface...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_right_port_corner_radius = 5 custom_left_port_corner_radius = 5 custom_phone_width = 100 custom_bottom_port_corner_radius = 5...

We also offer other variations of this light if needed to fit your specific application, 120-277V AC, 12-24V DC, and 0-10V dimmable models.Our EPL-24-2L-LED-480V LED light fixture is NRTL Listed for United States and Canada approved for use in paint...

We also offer other variations of this light if needed to fit your specific application, 120-277V AC, 12-24V DC, and 0-10V dimmable models.Our EPL-24-2L-LED-347V LED light fixture is NRTL Listed for United States and Canada approved for use in paint...

The retainer is up higher than need be in the video for safety.--------------------------------------------------------------------------------------------------------------All parts printed in PETG, with standard Voron settings for rigidity.0.20...

You can get all 3D-models here: https://www.3dcontentcentral.com/parts/supplier/EFD,-Inc.aspx, I don't include them because I don't know the copyright situation. BLTouch: ------------ I added an adjustable BLTouch mount, for easy homing. No need...

Luckily, this model is not in tune anyway lol. Post-Printing Even at 0.06mm and surface-oriented settings, I have found that the interior surface of 3d printed woodwinds is still not smooth enough to get a really good timbre. To fix it, you could...

For the launcher and the “motor” (= nozzle and adapter) you can find additional info here: https://www.printables.com/model/46571-water-rocket-and-launcher-platform-complete-instru These parts have been proven to be working (see old video). The...