enscape save visual settings 3d models

Initially I tried the latest version, but everything was moving very slowly then and changing the servo speed settings did not change that. But if you use an older version, between 2.4.1 and 2.6 (didn't test further), everything works as planned. My...

Here I will set the accessories for the chassis which may be required. By this I mean mainly PCB clips and adapters, but also things that should make "Sammy" more beautiful. ### November 28, 2020: A well-rounded affair Of course, my Sambucca is...

I have merged these pieces and then cut them along the middle so they screw onto the modified railgasm set from the sides. They fit on a ender 3 or 5 build plate diagonally which results in a much cleaner look (in my opinion). Doesn't require support...

Re-meshing available upon request, eg adaptive mesh for lower poly count (this is the default setting and is as supplied), uniform mesh for easier editing, strict quads, tris, mixed, poly increase or decrease, etc. No charge to existing customers of...

Two boxes (12 sets) are 47mm wide, and fit next to tiles. **Corners** Use these around tiles that are on their own in a box. You can scale the height to the height of your tiles. 102mm is the inside of my Rue Morgue Box. Print it on it's side, so...

These settings are put into your slicer (I use Cura). See featured picture above of my test results. When plating in Cura, the outer wall was the part printed with E2. Therefore adjustments were made to its placement relative to the center square. I...

...Just make a good size "square" around that whole area and set the infill to 100%. You could of course just print the whole thing in 100% infill if you really like wasting plastic, but this thing is large and I would certainly recommend against that.

Print Settings Printer: Resolution: Infill: Notes: It may seem a bit counter-intuitive, but do not print this with supports. See the fifth bullet under Here's what I did in the summary above for an explanation. If you plan to use this as an actual...

Setup: Each player chooses a set of 4 same-colored dice. To determine the order of play, each player rolls one die with the highest roll going first, followed by the next highest going next and so on. Use a paper and pencil to record your scores. ...

Now, I don't need to lie on the ground, and I can control my iPhone from my watch.I also think a selfie looks more natural if you set the timer on your phone and take photos using a tripod, rather than holding your arm out with a selfie stick.Plan...

http://www.thingiverse.com/thing:1411956 Please refer to the print setting and images for additional information... and post images of your Happy Hoppers in use for others to see. ... Note: If you like this, check out the rest of my fun and practical...

Print Settings: * Printer: Colido Printrite DIY 3D printer * Rafts: No * Supports: No * Resolution: 0.3 * Infill: 30% Post-Printing: All you need to do is put the 8mm rods together – one long one corner to corner and two half the size for the other...

Print Settings Infill: 20% Notes: All parts can be printed without supports, except for the chin-rest Recommended printing parameters: 4 Shell thickness. 3 top down solid thickness. 20 % infill 0.20mm. layer heights. Post-Printing If you print on...

Layer height should be set to 0.15mm. The layer height is crucial that they are thin because there are only a few thin layers of plastic around the "T" button area. For me, when printing, I used eSUN Advanced PLA+ in 1.75mm on a Taz 6 with an...

I set to in Onshape with an idea, which, as I drew it, developed into two ideas, and then into two finished 3d printed objects. They both seem to work without clogging, and each has its own advantages and disadvantages.This is the second idea, based...

Printer Settings: * Printer Brand: MakerGear * Printer Model: M2 * Rafts: No * Supports: Yes * Resolution: 0.2mm layers * Infill: 30% * Notes: No supports are usually needed for the fan or the AA battery holder, but supports are required for the...

The default settings for TPU are slower than PETG, but this isn't a problem since the part is small anyway. Just schedule the color change, and swap in your PETG when it comes, allowing the print to finish with PETG. An example .3mf is provided, but...

 If needed I could add a  5mm version if I had the specs on the nut. The spacer, lug holes, and adjustable track are all set to 5mm.Print Instructions:     All parts need to be printed in a high temp filament PETG, ABS...

Project details and a full list of credits here: https://www.designthatmatters.org/covid-19 Print instructions3d-printed headband in PLA, roughly 50g/1.75oz per part. Outer envelope of 3d-printed headband is 191mm wide, 148.5mm long, and 52.5mm...

so I thought of using a Hepa filter from a small air purifier on the market and adapt it to my enclosure.The aspirator filter is optional, it is only needed if your case is well sealed and does not allow air exchange.for a case such as built with...

The actress has been playing on TV and film sets since she was 11 years old. One of those confused with Swedish player Alicia Vikander (Tomb Raider) won an Oscar in 2016. She was the first Marvel Series star with a female leader. And soon, he will...

Re-meshing available upon request, such as adaptive mesh for lower poly count (default setting), uniform mesh for easier editing, strict quads, tris, mixed, poly increase or decrease, etc. No charge to existing customers of the product. Many other...

NOTE: The cable drag chain wraps behind one of the beam mounts and will require a little extra length if your chain is set at an optimized length. I put back two links to the chain to cover the extra distance. <hr> Working on publishing the...

It also contains parts to covert your printer to house lipo batteries and be completely portable. Many details below and full companion video here: https://youtu.be/Cv5pEcBI5Hw Parts: Purchase the Monoprice Mini Delta: Amazon:...

In many cases the filenames include suggested print settings, but use common sense (or ask me if you have trouble). The pictures have been ordered in a reasonably sensible order now, with the STL previews being the parts themselves, followed by a...

This model was created based on a textbook assistant I crafted this model following the guidelines in a textbook. assistant The design of this model was inspired by a textbook I referenced. assistant The instruction for creating this model came...

Furthermore, it is a larger design: The 80mm 12V fan provides power to suck in all the bad things coming from the solder. Please also take a look at the print settings and post-processing section for more details. Some video footage of this fume...

It's one fewer set of batteries to worry about, and also you can still focus manually if you wish. You can search for "battery-less electric motor for telescope" on Google to find how to hack the motors, and there are a couple of videos on YouTube,...

Verify it yourself, don't order blindly (These are not affiliate links, but I do work for Adafruit and many of the links point there) ~400g Filament (I used PLA) 87 Keyswitches 87 (I'm using Kailh Purple) 87 Keycaps (I'm using a YMDK 125-key set) 87...

Print Settings Printer Brand: MakerGear Printer: M2 Rafts: Yes Supports: Yes Resolution: 2mm Infill: 30% Notes: The more delicate bone structures don't do well when you scale this model down too far. You can get an interesting conversation piece at...