flight stands for transformers 3d models

A bracket for the Adafruit VL6180X (https://www.adafruit.com/product/3316) or the VL53L0X Time of Flight Distance Sensor. In fact it will hold any breakout board using the 0.8 X 0.7 in form factor, that has the communications pins in the same...

This is an updated version of the basic framework from EMaglio's renowned quad configuration, enhanced with attachment points specifically designed to accommodate standard 30.5mm-attached flight control systems.

This design tweaks EMaglio's popular quad layout, bringing forth new functionality with added attachment points specifically engineered to support standard 30.5mm sized flight control units, further elevating their usability and versatility.

you shouldn't try to print several at stands at once, as the printer will drag the thin stand to the side when moving the extruder from one stand to another. print this with 100% infill to make the base get some weight to it to make the planes...

This is a G1000 master panel for your homemade flight simulator. This model was inspired by the G1000 10.4" flight simulator panel made by FlightSimMaker. (https://www.thingiverse.com/thing:4019943). The panel has the following; a Standby battery...

https://www.printables.com/social/287681-gutbomb/about Introduction ----------------------------------------------------- I've wanted a trim wheel for flight sim stuff for years but the old Saitek model isn't made anymore and examples on eBay are...

I've wanted a trim wheel for flight sim stuff for years but the old Saitek model isn't made anymore and examples on eBay are rare and cost a fortune so I decided to make my own.This is built with an Arduino Leonardo, some 3d printed parts, and a...

Introducing a customized swivel clamp case crafted specifically for Hobby King KK 2.0 multirotor flight controller board (XL-RCP7.0). This innovative design includes three components: the base, main case, and lid. Designed with ease of maintenance in...

C-RTK GPS Flight Controller GPS with Protective Shell for PIX PX4 Pixhawk pixhackHigh-precision positioning: Many drone applications require higher accuracy than traditional GNSS offerings, such as drone mapping, agricultural surveying, and high...

This solution is specifically designed for the following: Virpil CM2 or CM3 base Virpil 200mm extension pipe AND Virpil Z extension The Counter Weight works near 0 degrees for the Constellation Alpha grip. Mine was 0.1 degrees off center which I...

... sides, and a 3mm stand port on the bottom (not pictured)! The Weaponized Energon Cube is also loosely based on the storage containers for Energon from Transformers: Prime, but is meant to look more like a cube of Energon modified into a blaster.

### Description **If you print in the orientation provided, you shouldn't need supports.** **Also included in the photos is my [Case for ElectroCookie Mini PCB Prototype Board](https://www.thingiverse.com/thing:5320880).** This housing is designed to...

This is a Garmin GTN 750 Frame for use in a Flight Simulator cockpit. Credit to Håkon Furdal for his detailed 2D technical drawings which allowed me to make this file. All measurements were to scale when this thing was made, but it can be scaled in...

I found the center detent on my Thrustmaster T.Flight Hotas X to be completely unnecessary. I would much rather have no detent or, better yet, have a mil power detent! Some people have removed the detent by filing down the little nub that engages...

The flight base is sized to accommodate Micro-Machine ships, like the A wing; the painted ship has a scaled up appearance but prints well at small sizes. To ensure precise curves, full support was used during printing. ...This creation was entered into...

This tool is used to slice O-rings from nylon tubing for indoor free flight rubber powered models. Three slicers are presented. These slicers cut very uniform thickness O-rings for repeatable results.The small slicer is used to cut Dubro 511 tubing,...

My custom flight sim control setup occasionally interferes with other games, so I prefer to disconnect it when not in use. I designed these adapters after repeatedly attempting to take off in a WWII warbird without properly connecting my rudder...

I use it for X-Plane 11 myself.\r\nThe following items are used to make this box work:\r\n\r\nCable: Check out these awesome jump wires on Amazon -...

100% functional A320 throttle quadrant for flight simulator. It's my own design, made for myself. Sold many of them on my country but now I'm not able to continuie with the project so I decided to open it. I made a full instructive with pictures...

Here's a rudder and elevator trim controller for flight simulators (Flightgear, X-Plane, MS Flight Sim etc). Designed to match with the Logitech/Saitek yoke/throttle quadrant. Can be mounted to the left side of the quadrant. Version 2 now...

I am equipping my flight simulator with a Bendix King KMA 28 system. Electronics include: Tactile buttons, 10 of them measuring 6 by 6 by 8 millimeters each; green LEDs, 13 in total, with 3 millimeters in length and varying numbers of 5 millimeters...

This is an OpenSource Yoke to be used with flight simulators! Due to a bug in Thingiverse's website (never emailed me back!), the first version exists only as a link and was not posted on my maker page or in searches. This is a re-upload to...

Thank you Tom Stanton for designing this awesome flight simulator project. However, some of the parts used in the project are quite hard to obtain. So I designed a few hacks to get around that issue and make it work with more easily obtainable parts....

This is an OpenSource Yoke to be used with flight simulators!Due to a bug in Thingiverse's website (never emailed me back!), the first version exists only as a link and was not posted on my maker page or in searches. ...This is a re-upload to resolve...

I've been messing around with the idea of making a throttle housing for my flight simming, and I printed some awesome throttle and mixture knobs (big thanks to AlbEagle). I wanted to get them integrated into something that was printable and useful...

The goal was to make CaptainBob's keyswitch easier to assemble: * Uses a keyed slot to position the lock body rather than the captive nut, which made it difficult to tighten properly while keeping desired lock alignment * Integrates the metal...

This mod is the follow-up for the 180 degree rotation mod that was applied to the Saitek Pro Flight Yoke. More info about the earlier mod can be found here: https://www.thingiverse.com/thing:4596632 This is the holder for the Leo Bodnar's BU0836A...

I have a cup holder in my chair that is exactly where the joystick would stand well. So I adjusted the mount so that it fits exactly. ...I don't know if anyone has exactly the right criteria, but maybe this model will serve someone as a good inspiration...

This is all about giving them a run for their money.

The platform should be glued to the risers for stability as the hole is not very deep. For reference, I find the 1.7mm bases with the 40mm risers work best for me. I expect 10 Risers will suffice for a game. For bases, I've printed: 2x Red 8x Yellow...